Hitachi cp-s318 Related Messages, What To Do When You Think A Machine Defect Has Occurred

Page 37
WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED

CP-S317/327W/Vol2-E責了03.5.27 2:31 PM ページ 7

WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED

Related Messages

When the unit's power is ON, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below.

Message

Description

 

 

CHANGE THE LAMP

Lamp usage time is approaching 2,000 hours. (Note 2)

AFTER REPLACING LAMP,

Preparation of a new lamp, and an early lamp change, is

recommended. After you have changed the lamp, please be

RESET THE LAMP TIMER.

(Note 1)

sure to reset the lamp timer.

 

 

CHANGE THE LAMP

Lamp usage time is approaching 2,000 hours. A lamp change

within ＊＊ hours is recommended. (Note 2)

AFTER REPLACING LAMP,

When lamp usage reaches 2,000 hours, the power will

RESET THE LAMP TIMER.

automatically be turned OFF. Please change the lamp by

THE POWER WILL TURN OFF

referring to “THE LAMP” in Vol.1 (Basic). After you have

AFTER ＊＊ hr.

changed the lamp, please be sure to reset the lamp

(Note 1)

timer.

 

 

CHANGE THE LAMP

As lamp use has reached 2,000 hours, the power will soon be

automatically turned OFF. (Note 2)

AFTER REPLACING LAMP,

Please immediately turn the power OFF, and follow the

RESET THE LAMP TIMER.

instructions in the “THE LAMP” section of the separate booklet,

THE POWER WILL TURN OFF

Vol.1 (Basic).

After you have changed the lamp, please be sure to reset the

AFTER 0 hr.

 

lamp timer.

CLEAN THE AIR FILTER

A note of precaution when cleaning the air filter.

AFTER CLEANING AIR FILTER,

After cleaning the filter, operate FILTER TIME of the OPTION

RESET THE FILTER TIMER.

Menu, and perform reset of the filter timer.

 

 

NO INPUT IS DETECTED

There is no input signal.

Please confirm the signal input connection, and the status of the

ON ＊＊＊

signal source.

 

 

 

SYNC IS OUT OF RANGE

The horizontal or vertical wavelength of the inputted signal is

outside of the response parameters of this unit. Please confirm

ON ＊＊＊ fH ＊＊＊＊＊kHz fV ＊＊＊＊＊Hz

the specs for this unit or the signal source specs.

 

 

 

The internal portion temperature is rising. Please turn the power

 

OFF, and allow the unit to cool down for approximately 20

 

minutes. After having confirmed the following items, then please

CHECK THE AIR FLOW

resent the power to ON.

 

• Is there blockage of the air passage aperture?

 

• Is the air filter dirty?

 

• Does the peripheral temperature exceed 35°C?

 

 

NOTES

Note 1: Although this message will be automatically disappeared after around 3 minutes, it will be reappeared every time the power is turned ON.

Note 2: Lamps have a finite product life. Lamps are characterized by the fact that, after long hours of usage, a lamp will no longer light up, or the lamp will break or burst, etc. This unit is equipped with an automatic shut-down function, such that the power will automatically be turned OFF when lamp usage time has reached 2,000 hours. Please be aware, however, that among lamp types, there are major differences in product lifetimes; a lamp may thus fail to light even prior to the functioning of the automatic shut-down function of this unit.

7

Page 36 Page 38
Image 37
Page 36 Page 38
Contents MANUALE DISTRUZIONI Vol.1 Informazioni di base CP-S318W/CP-X328WBRUKERHÅNDBOK Vol.1 Grunnleggende ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS NORSK PORTGÊSSETTING UP CONTENTSCONNECTING USING THE REMOTEUltra High Brightness PROJECTOR FEATURESKeystone Distortion Correction Partial Magnification FunctionConnect your devices to the projector 3 Connect the power cord8 ～ Insert the batteries into the remoteTHE PROJECTOR PART NAMESTHE REMOTE CONTROL Adjusting the Projectors Elevator Feet SETTING UP THE PROJECTORPress and hold in the elevator 1 buttons Raise or lower the projector to theIf 43 aspect ratio Adjusting the Screen Size and Projection DistanceIf 169 aspect ratio Indicates the corresponding reference page CONNECTING YOUR DEVICESNOTE About Plug-and-Play Capability Ports and CablesConnecting to a Computer CONNECTING YOUR DEVICES continuedLaptop computer Desktop computerConnecting to a VCR Connecting to a DVD PlayerDVD player If using a componentDisplay monitor Connecting to a Display MonitorRGB OUT RGB IN Putting batteries into the remote control unit USING THE REMOTE CONTROLOperating the remote control 3 Closecover the batteryPrecautions TURNING ON THE POWERMake sure that the power cord is firmly and Turn on the projectors powerUsing the remote control If selecting RGB input Press the RGB button Selecting an Input SignalUsing the projectors control panel Press the INPUT button Use the zoom ring to adjust thepanel or remote control TURNING OFF THE POWERcontrol panel or remote control Check that the POWER indicator stopsPress the VOLUME button ADJUSTING THE VOLUMEbuttons to adjust the volume1 Press the POSITION button ADJUSTING THE POSITIONUse the the positionAutomatic Adjustment for RGB Input USING THE AUTOMATIC ADJUSTMENT FEATUREAutomatic Adjustment for Video Input Press the AUTO buttonPress the KEYSTONE button CORRECTING KEYSTONE DISTORTIONSbuttons to select the direction of distortion to correctFREEZING THE SCREEN USING THE MAGNIFY FEATUREPress the MAGNIFY ON button press the POSITION button again to confirm yourSELECTING THE ASPECT RATIO SIGNAL SEARCHINGTEMPORARILY BLANKING THE SCREEN 1 Press the SEARCH button2 Select a menu using the USING THE MENU FUNCTIONSSelect an item using the buttons to adjust the levelOPERATING THE PC SCREEN You can use the remote control as a simplified mouse or keyboardPS/2, ADB, Serial Mouse Control USB Mouse/Keyboard ControlTHE LAMP Replacing the lamp THE LAMP continuedApply a vacuum cleaner to Turn off the projector, and unplug the power cordto clean the air filter Turn on the projector, and use the menu to reset the filterTurn on the projector power, and using the menu, reset the Turn off the projector, and unplug the power cord. Prepare afilter timer THE AIR FILTER continuedOTHER CARE Caring for the cabinet and remote control transmitterCaring for the inside of the projector Caring for the lensCP-S317/327W/Vol2-E責了 03.5.27 230 PM ページ MAIN Menu MULTIFUNCTIONAL SETTINGSMAIN Menu PICTURE 2 Menu PICTURE 1 MenuPICTURE1 Menu PICTURE2 MenuINPUT Menu MULTIFUNCTIONAL SETTINGS continuedINPUT Menu SCREEN Menu SCREEN MenuOPTION Menu OPTION MenuWHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED Related MessagesFlashing of the green lamp Regarding the Indicator LampsThe green lamp is lighted Flashing of the orange lampPhenomena That May Easily Be Mistaken for Machine Defects WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED continuedDimension Diagram SPECIFICATIONSSpecification WARRANTY AND AFTER-SERVICE TECHNICAL SIGNAL CONNECTOR PIN ASSIGNMENTCP-S318/328W/TECHNICAl責了 03.5.27 239 PM ページ Resolution EXAMPLE OF COMPUTER SIGNALSignal mode fH kHzThe following signals are used for the initial settings INITIAL SET SIGNALSADB Mouse CONNECTION TO THE MOUSE CONTROLUSB Mouse PS/2 Mouse3 Command data Communications settingCommand data chart RS-232C COMMUNICATIONChanging the projector settings Set command Requesting projector status Get commandUsing the projector default settings Reset Command Increasing the projector setting value Increment commandCommand data chart Command data chart continued H.Phase DefaultContrast KeystoneHCP-S318/328W/TECHNICAl責了 03.5.27 239 PM ページ FCC Statement Warning REGULATORY NOTICESFor the Customers in CANADA Pour les utilisateurs au CanadaQR57451
Top Page Image Contents