Hitachi CP-X1200 user manual Be careful in handling the light source lamp

Page 5

Safety Precautions (continued)

WARNING

Be careful in handling the light source lamp.

The projector uses a high-pressure mercury glass lamp made of glass. The lamp can break with a loud bang, or burn out. When the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

Please carefully read the section “Lamp”.

Be careful in handling the power cord and external connection cables. If you keep using a damaged the power cord or cables, it can cause a fire or electrical shock. Do not apply too much heat, pressure or tension to the power cord and cables.

If the power cord or cables is damaged (exposed or broken core wires, etc.), contact your dealer.

•Do not place the projector or heavy objects on the power cord and cables. Also, do not place a spread, cover, etc, over them because this could result in the inadvertent placing of heavy objects on the concealed power cord or cables.

•Do not pull the power cord and cables. When connecting and disconnecting the power cord or cables, do it with your hand holding the plug or connector.

•Do not place the cord near the heater.

•Avoid bending the power cord sharply.

•Do not attempt to work on the power cord.

Be careful in handling the battery of the remote control.

Incorrect handling of the battery could result in fire or personal injury. The battery may explode if not handled properly.

•Keep the battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.

•Do not allow the battery in a fire or water.

•Avoid fire or high-temperature environment.

•Do not hold the battery with the metallic tweezers.

•Keep the battery in a dark, cool and dry play.

•Do not short circuit the battery.

•Do not recharge, disassemble or solder the battery.

•Do not give the battery a physical impact.

•Use only the battery specified in the other manual of this projector.

•Make sure the plus and minus terminals are correctly aligned when loading the battery.

•If you observe a leakage of the battery, wipe out the flower and then replace the battery. If the flower adheres your body or clothes, rinse well with water.

•Obey the local laws on disposing the battery.

4

Image 5

Contents CP-X1200 / CP-X1250 About The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Arrangement Contents Of PackageIf using a M1-D input to mouse control Connecting Your DevicesIf using a BNC input ComputerProjectorIf using a component signal If using a s-video signalMonitorProjector SpeakerProjectorAdjusting The Projectors Elevator Connecting The Power SupplyPeople. The laser beam can cause vision problems Preparing Remote ControlTrademark Acknowledgment Preparation Projector FeaturesContents Projector Part NamesProjector Front/Right Audio in 1 port E Audio in 2 portControl Buttons Remote ControlRemote Control Arrangement Setting Up100 Adjusting The Projectors ElevatorUsing The Lens Shift Buttons Connecting Your Devices Examples of connection with a computer Audio Scart Audio IN-L Video If using a Scart RGB inputCR/PR Scart CB/PB Connecting The Power Supply Putting Batteries Remote ControlAbout The Laser Pointer Using The Remote ID Feature Operating The Remote ControlUsing The Mouse/Keyboard Control Function Turning Off The Power Power ON/OFFTurning On The Power Operating Selecting An Input SignalAt a M1-D signal Using The Automatic Adjustment FeatureAt a RGB signal not M1-D At a video signal At a RGB signalCorrecting The Keystone Distortion Adjusting The Picture PositionPosition Use the cursor buttons Dialog and complete this operationTemporarily Blanking The Screen Adjusting The VolumeMuting The Sound Press the Magnify Button Using The Magunify FeatureFreezing The Screen Selecting An Audio Input Displaying The Child WindowEx. Turning off the built-in speaker Multifunctional SettingsUsing The Menu Functions Main Menu PICTURE-1 Menu SAVE1 SAVE2 SAVE3 SAVE4 PICTURE-1 MenuLOAD1 LOAD2 LOAD3 LOAD4 Size PICTURE-2 MenuPosition Color Space Input MenuComponent 3D-YCSInput Menu Power OFF AdjustPower on Auto MenuRGB BNC Auto MenuSearch Video ComponentBlank Screen MenuStart UP Menu PositionMessage How to register your picture as the MyScreenScreen Menu Option Menu Option Menu Network Menu SetupDhcp OFFEx. Case of IP Address = Network Setting UpClick Return to top Click Reboot to complete this operation Lamp Knob Replacing The LampDealer to replace the lamp Caring For The Air Filter Air FilterOther Care Caring For The Cabinet And Remote ControlCaring For The Inside Of The Projector Caring For The LensRelated Messages TroubleshootingRelated Messages Regarding The Indicator Lamps Regarding The Indicator Lamps Phenomena That May Easily Be Mistaken For Machine Defects Such as by a power outage blackout, etcSound is muted Phenomena That May Easily Be Mistaken For Machine DefectsSpecifications Warranty And After-ServiceTechnical DimensionsVesa Example Of Computer SignalVesa Text Initial Set Signals Dia. Stereo mini jack MVrms, 57k Ω terminator Connection To The PortsMini Din 4 pin jack VideoRTS D-Sub 9 pin RS-232C portPlug Jack RJ-45 10BASE-T jackRS-232CCommunication Connecting The CableCommunications Setting Requesting projector status Get command Command Data Chart Français Command Data ChartBe EF EF F6 Be EF EC D9 Auto RGB Turn on Be EF Be EF BA D2 RGB Be EF Be EF RGB