Hitachi PW1 user manual Operating Instructions, Turning Power On and Off, Indicating lamp

Page 17

OPERATING INSTRUCTIONS

Indicating lamp

Main power switch

Turning Power On and Off

•To turn the monitor power ON, press the main power switch on the monitor main unit to ON, and then press the SUB POWER button or the ON/OFF or ON button on the remote control.

•To turn the monitor power OFF, press the SUB POWER button or the ON/OFF or OFF button on the remote control, and then press the main power switch on the monitor main unit to OFF.

•During normal use, the main power switch is set in the ON position, and the monitor can then be turned ON/OFF using the SUB POWER button or the ON/OFF button on the remote control.

									Indicating lamp
									Indicating lamp


									Indicating	Power status	Operating
									lamp	Power status	Operating
									lamp

									Off	Off	When the main power switch is set
									Off	Off	to OFF.
											to OFF.

											When the main power switch is
										Off	ON, and the OFF button on the


									Lights red		remote control or the SUB POWER
										(standby)

											button on the underside of the
											button on the underside of the
											front of the frame is OFF.
											front of the frame is OFF.

											When the main power switch is
											ON, and the ON button on the
									Lights green	On	remote control or the SUB POWER
											button on the underside of the
											front of the frame is ON.

											When the main power switch is
SUB-POWER button											ON, and the ON button on the
										Off	remote control or the SUB POWER
									Lights orange	Off	button on the underside of the
									Lights orange	(Power Save)	button on the underside of the
										(Power Save)	front of the frame is ON.
											front of the frame is ON.
											However, the state in POWER
											SAVE mode

	POWER OFF
	button
	POWER ON	POWER ON/OFF
	POWER ON	button
	button	button
	button
		VOL
		RGB 1 RGB 2 MUTE VOL

AV1 AV2 AV3 AV4

AUTO PinP SIZE RECALL

MENU

When the indicating lamp lights in orange or the message “No Sync. Signal”, “Power Save” or “Invalid Scan Freq.” appears on the screen, there is something unusual about the status of reception.

See “Power Save Mode” or “Symptoms That Seemingly Appear to be Failures.” 25 27

ATTENTION

•Avoid repeatedly turning the monitor on and off at short time intervals. Failures might result from such operation.

•Turn off the main power switch before leaving the monitor out of use for an extended period of time.

•If a power failure occurs while the main unit is running, it would be powered on upon recovery from the failure. Turn off the unit main power switch before leaving the main unit.

OK

ID

ID SET

16

Image 17

Contents 42HDM70 English Power Source Important Safety InstructionsPrevention of Screen Burn Disposal of this product may require specific instructionsPublic Viewing of Copyrighted Material Read before operating equipmentFeatures Contents About the Symbols Safety InstructionsBe cautious of the power cord connection Safety InstructionsBe sure to keep safety ground connection Be careful in handling the battery of the remote controlRemove the power cord for complete separation Avoid a high temperature environmentInstallation environment How to view the monitorPrecaution during transportation Precautions for the cable connectionDo not physically impact the remote control Set the sound volume at a suitable levelFCC Federal Communications Commission Statement Warning Main Unit Component NamesLoading Batteries Component Names Remote controlHandling the Remote Control Installation Installation InstructionsAnti-tumble measures Securing to a wall or pillarMonitor rear panel Installation InstructionsConnecting to a PC English Operating Instructions Turning Power On and OffIndicating lamp IndicatingInput Switching Operating Instructions Volume AdjustmentWhen a button is pressed, the volume adjustment Audio MuteInput Signal Screen Display Size SwitchingDisplay area selection diagram RGB input Operating InstructionsAutomatic Adjustment of Screen Position and the Clock Operating Instructions Using the Menu ScreenOn-screen display system Independent Operation of Multiple Monitors ID NoPicture Menu Audio Menu Timer Menu60Min Function MenuSetup Menu Language Menu Other FeaturesAutomatic Store Menu Display Registration conditionPower Save Mode Other Features Signal CheckWhen the RGB1, RGB2 input is selected Status Display ActionMethods to Reduce the Occurrence of Image Retention Image Retention of Plasma DisplayAbout screen defects About residual imagesSymptoms That Seemingly Appear to be Failures TroubleshootingSymptom Point to check Check the way the signal cable is connectedSymptom Point to check Example Troubleshooting Actions to Correct Abnormal DisplaysSignal Input Product SpecificationsRGB terminal D-sub 15-pin connector Pin Input signalRecommended Signal List Product Specifications Signal InputWith Digital RGB signal input RGB1 input Pin Input signalXGA Product Specifications Recommended Signal ListWith Analog RGB signal input RGB2 input Supplement An example of connecting video imaging devices Connecting to a Video Imaging DeviceWith DVI-STB and RGB component setup Optional Video Unit FunctionFull Display size selection diagramAV1 AV2 AV3 RGB2 RGB1 AV4 Position + Using a wide-screen monitorPictures Split Operating Instructions Displaying Multi PictureYNR YNR Operating Instructions Picture MenuCNR LTIItem is added to the Menu shown AV4 AV1AV2 AV3 RGB1 Operating Instructions Setup MenuAV1 AV2 AV3 AV4 Video input Pin Signal Input connector pin specificationsScart connector pin specifications With component input AV1, AV2 and RGB2-component input With R, G, B Video input AV2 and AV4 inputKHz MHz 525Remarque QR58563