Hitachi PW1 user manual FCC Federal Communications Commission Statement Warning

Page 11

SAFETY INSTRUCTIONS(continued)

• FCC (Federal Communications Commission) STATEMENT WARNING

For model 42HDM70

WARNING : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a paricular installation. If this equipment does cause harmful inerference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from where the receive is connected.

-Consult the dealer or an experienced radio / TV technician for help.

Instructions to Users : This equipment complies with the requirements of FCC (Federal Communication Commission) regulations, provided that following conditions are met.

Video inputs : The input signal amplitude must not exceed the specified level.

CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

 

Declaration of Conformity

 

According to 47CFR, Part 2 and 15 for

 

Class B Personal Computers and

 

Peripherals; and / or

 

CPU Boards and Power Supplies used

 

with Class B Personal Computers:

We:

Hitachi America, Ltd. Home Electronics Division

Located at: 900 Hitachi Way. Chula Vista, CA 91914, U.S.A.

Telephone: 1-800-HITACHI

Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device. Each product marketed, is identical to the representative unit tested and found to be compliant with the standards. Records maintained continue to reflect the equipment being produced can be expected to be within the variation accepted, due to quantity production and testing on a statistical basis as required by 47CFR § 2.909. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The above named party is responsible for ensuring that the equipment complies with the standards of 47CFR § §1 5.101 to 15.109.

Trade name:

Plasma Display Monitor

Model Number:

42HDM70

10

Image 11
Contents 42HDM70 English Power Source Important Safety InstructionsRead before operating equipment Disposal of this product may require specific instructionsPrevention of Screen Burn Public Viewing of Copyrighted MaterialFeatures Contents About the Symbols Safety InstructionsBe careful in handling the battery of the remote control Safety InstructionsBe cautious of the power cord connection Be sure to keep safety ground connectionHow to view the monitor Avoid a high temperature environmentRemove the power cord for complete separation Installation environmentSet the sound volume at a suitable level Precautions for the cable connectionPrecaution during transportation Do not physically impact the remote controlFCC Federal Communications Commission Statement Warning Main Unit Component NamesLoading Batteries Component Names Remote controlHandling the Remote Control Securing to a wall or pillar Installation InstructionsInstallation Anti-tumble measuresMonitor rear panel Installation InstructionsConnecting to a PC English Indicating Turning Power On and OffOperating Instructions Indicating lampAudio Mute Operating Instructions Volume AdjustmentInput Switching When a button is pressed, the volume adjustmentOperating Instructions Size SwitchingInput Signal Screen Display Display area selection diagram RGB inputIndependent Operation of Multiple Monitors ID No Operating Instructions Using the Menu ScreenAutomatic Adjustment of Screen Position and the Clock On-screen display systemPicture Menu Audio Menu Timer Menu60Min Function MenuSetup Menu Menu Display Registration condition Other FeaturesLanguage Menu Automatic StoreStatus Display Action Other Features Signal CheckPower Save Mode When the RGB1, RGB2 input is selectedAbout residual images Image Retention of Plasma DisplayMethods to Reduce the Occurrence of Image Retention About screen defectsCheck the way the signal cable is connected TroubleshootingSymptoms That Seemingly Appear to be Failures Symptom Point to checkSymptom Point to check Example Troubleshooting Actions to Correct Abnormal DisplaysPin Input signal Product SpecificationsSignal Input RGB terminal D-sub 15-pin connectorPin Input signal Product Specifications Signal InputRecommended Signal List With Digital RGB signal input RGB1 inputXGA Product Specifications Recommended Signal ListWith Analog RGB signal input RGB2 input Supplement Optional Video Unit Function Connecting to a Video Imaging DeviceAn example of connecting video imaging devices With DVI-STB and RGB component setupFull Display size selection diagramAV1 AV2 AV3 RGB2 RGB1 AV4 Position + Using a wide-screen monitorPictures Split Operating Instructions Displaying Multi PictureYNR LTI Operating Instructions Picture MenuYNR CNRItem is added to the Menu shown AV4 AV1AV2 AV3 RGB1 Operating Instructions Setup MenuAV1 AV2 AV3 AV4 Video input Pin Signal Input connector pin specificationsScart connector pin specifications 525 With R, G, B Video input AV2 and AV4 inputWith component input AV1, AV2 and RGB2-component input KHz MHzRemarque QR58563