Hitachi 42PD5000 Connecting Antenna, Precautions when connecting the antenna, Monitor rear panel

Page 48

INSTALLATION INSTRUCTIONS

Connecting Antenna

Make sure that the power switch of the monitor is turned off.

Speaker (R)

Monitor rear panel

Speaker (L)

antenna

20 18 16 14 12 10 8 6 4 2

21 19 17 15 13 11 9 7 5 3 1

Precautions when connecting the antenna

•Please use a coaxial cable which is free from interference to connect the antenna. Avoid using a parallel flat feeder wire as interference may occur, causing reception to be unstable and stripe noise to appear on the screen.

•Avoid using indoor antenna as this may be affected by interference. Please use CATV net or outdoor antenna.

•Keep the power cord as far away from the antenna wire as possible.

If there are noise appearance in the picture of VHF-Low band channel, please use the double-shielded cable (not provided) for RF LEADS to reduce the noise.

Image 48

Contents 32PD5000 42PD5000 42PMA500 Remarque English Features Contents Safety Instructions About the SymbolsBe cautious of the power cord connection Be sure to keep safety ground connectionBe careful in handling the battery of the remote control To Earth Fuse Blue to Neutral Cord ClampSafety Instructions Precautions for the cable connection Precaution during transportationDo not physically impact the remote control Set the sound volume at a suitable levelComponent Names Main UnitRemote control Handling the Remote ControlLoading Batteries Installation Instructions InstallationAnti-tumble measures Securing to a wall or pillarConnecting to a PC Monitor rear panelPage Turning Power On and Off Operating InstructionsOperating Instructions Volume Adjustment Input SwitchingWhen a button is pressed, the volume adjustment Audio MuteSize Switching Input Signal Screen DisplayDisplay area selection diagram RGB input Using the Menu Screen On-screen display system Automatic Adjustment of Screen Position and the ClockOperating Instructions Independent Operation of Multiple Monitors ID NoPicture Menu Timer Menu Off Timer Min 30Min 60Min 120Min 90Min On TimerAudio Menu Selected charactersFunction Menu Setup Menu MovieOther Features Language MenuAutomatic Store Menu Display Registration conditionOther Features Signal Check Power Save ModeWhen the RGB, RGB2 input is selected Status Display ActionImage Retention of Plasma Display Methods to Reduce the Occurrence of Image RetentionAbout screen defects About residual imagesTroubleshooting Symptoms That Seemingly Appear to be FailuresSymptom Point to check Check the way the signal cable is connectedEnglish Troubleshooting Actions to Correct Abnormal Displays ExampleProduct Specifications Signal InputRGB terminal D-sub 15-pin connector Pin Input signalProduct Specifications Signal Input Recommended Signal ListWith Digital RGB signal input RGB1 input Pin Input signalWith Analog RGB signal input RGB2 input Supplement Connecting to a Video Imaging Device An example of connecting video imaging devicesWith DVI-STB and RGB component setup Optional Video Unit FunctionDisplay size selection diagram When you want toInput signal Display screen Remarks AV1 AV2 AV3 RGB2 RGB1 AV4Using a wide-screen monitor Position +Operating Instructions Displaying Multi Picture Pictures SplitTime will display 2 pictures YNR Film Mode PAL Comb Filter Operating Instructions Picture MenuBlack Enhancement Auto Colour Colour Management MagentaRed YellowSystem Colour System Video InputAV2 1st step AV2 2nd step Audio Input Scart OutputRGB2 1st step RGB2 2nd stepVideo input Input connector pin specifications Scart connector pin specificationsPin Signal PinProduct Specifications Recommended Signal List With R, G, B Video input AV2 and AV4 inputWith component input AV1, AV2 and RGB2-component input KHz MHz Remote control provided for the optional tuner unit Optional Tuner Unit FunctionYou may recall the picture mode by Picture mode is changed in followingPress this button to change input Surround On or Off Mode Pressing this button. Each time pressedButtons for Teletext Mode Connecting Antenna Precautions when connecting the antennaMonitor rear panel During TV mode TV AV1 AV2 AV3 RGB2 RGB1 AV4Auto Full Zoom 149Zoom C149L Activating the Split mode from the TV screen Multi Picture button Multi Mode button ButtonPictures Split 4 pictures 12 pictures Select buttonsSound mode Off-timerPictures Display will go out in approximately 6 seconds TV positionPicture Freezing Freeze buttonSplit Strobe During TV mode AbcdeOperating Instructions Setup Menu During Video signal inputAuto Off Other Functions A2 / Nicam / Sound MultiplexBilingual / Dual sound broadcast Stereo sound broadcastMode button Index button TV / Text button Cancel button Operating Instructions Other FunctionsDVD Player Selection ExampleSymptom Possible reason Remedy Snowy picture poor soundMultiple images sound O.K Intermittent interferenceRF input Input signals Input terminals To dealers and shops Parts packingParts for CL37-PD2100 only Required general Disassembly Prohibited GeneralForbidden General Installation on a wooden wall Installation on a concrete wallDo not install Locations where thereM6 x 18 screw x Cutout Wall-mount metal top CenterBottom Wall-mount metalMounting the wall-mount unit on the wall Installing the TV-mount metals Wire clampsRemove the stand Remove the 4 screws Remove the screws CL37-PD2100 StandTV-mount metal M6 x 18 screws M6 x 18 screws Bracket 1st TV-mount Metal hole2nd TV-mount metal hole 5th TV-mount metal hole External Dimensions Angle adjustmentMass Main materialModel Serial Number DEALER/STORE Date Purchased Hitachi Atago Building

Related manuals

Manual 76 pages 6.24 Kb