JBL DD66000 manual Placement and Set-up Considerations

Page 19

Project EVEREST DD66000

CHAPTER 7

Placement and Set-up Considerations

The Project EVEREST DD66000 loudspeaker system is designed to be less affected by room acoustics than conventional imaging systems. However, it is very sensitive to overall symmetry, proximity to walls, ceilings and corners.

Ideally, any listening room should contain a combination of live surfaces (e.g., walls and windows) and absorbent surfaces (e.g., drapes, carpets, upholstery). If the distance between floor to ceiling is low, it is preferable that one surface has an absorbent covering. With Project EVEREST DD66000, it is most important to be able to accommodate the optimum listening area that is defined by the 100° horizontal/60° vertical coverage pattern of the horn.

In order to obtain the best stereo effect, the speakers should be placed at the same distance from the listening position.

The distances to the right and left speakers are determined by the relationship between the

distance from the listening position to the speakers and the angles of the speakers (refer to the figure on the right). The imaging qualities enable the speakers to be placed relatively far apart from each other, but this weakens center imaging such as vocal. By increasing the inward angle of the

speakers toward the listener will improve the center imaging.

The listener should be centered in front of the speakers and furniture should be of an appropriate height so that when the listener is sitting, the ear level is on a vertical plane with the high-frequency horn (approximately

90 cm/ 35.5 in) as illustrated on the right.

The surrounding environment for the speakers affect bass sound quality. Placing the speakers close to wall behind them or side walls bring about abundance of bass, but too close distance will result in dull bass. On the other hand, too much distance will reduce the mass of bass but result is in

Image 19
Contents Project Everest DD66000 Users Guide Table of Contents Chapter Defining the Project Concept Project Everest DD66000 Page Project Everest DD66000 Chapter Project Everest DD66000 1501AL section view 1501AL Low Frequency Driver476Be section view 476Be High Frequency Compression Driver and HornPage 045Be-1 section view 045Be-1 Ultra-High Frequency Compression Driver and HornDD66000 system impedance Internal Crossover NetworkUnpacking the Project Everest DD66000 System Grille Removal Selecting Cable Amplifier Recommendations Placement and Set-up Considerations Floor Requirements System Orientation Project Everest DD66000 Switch OperationsHF Drive / LF Drive LF Level HF LevelBattery Installation Project Everest DD66000 Project Everest DD66000 Connections II. Bi-Wire Connecting Method Passive Connecting MethodIII. Bi-Amp Connecting Method Final Checklist Project Everest DD66000 Care and Maintenance Troubleshooting and Service Guide Project Everest DD66000 Register Project Everest DD66000 System Specifications USA JBL and Harman International

DD66000 specifications

The JBL DD66000 is a flagship model in the world of high-fidelity loudspeakers, designed to deliver an exceptional listening experience for audiophiles and music enthusiasts alike. With its rich heritage rooted in decades of acoustic engineering expertise, the DD66000 represents the pinnacle of JBL's commitment to superior audio performance.

One of the standout features of the DD66000 is its innovative three-way speaker configuration. This includes a 15-inch bass driver, a 4-inch midrange driver, and a high-frequency compression driver that produces crystal-clear treble. This arrangement allows for a wide frequency response, ensuring that every note, from the lowest lows to the highest highs, is reproduced with remarkable accuracy and detail.

The DD66000 boasts advanced technologies that enhance its performance. The Integrated Waveguide Technology ensures that sound is evenly distributed throughout the listening space, creating a spacious and immersive soundstage. This technology minimizes distortion and ensures that the sound maintains its clarity, even at high volumes. Additionally, the dual high-frequency compression drivers provide extended dynamic range, allowing the speaker to handle both quiet and loud passages seamlessly.

Another key characteristic of the JBL DD66000 is its robust build quality. The speaker is encased in an elegantly crafted cabinet that not only minimizes resonance but also adds to its aesthetic appeal. The sleek design incorporates high-quality materials, giving it a premium look that complements any audio setup.

The DD66000 is also versatile in its connectivity options. Designed to work seamlessly with various audio components, it features compatibility with both analog and digital sources. Audiophiles can enjoy their favorite music in high-resolution formats, ensuring that every detail is captured and enjoyed.

In summary, the JBL DD66000 is a masterful integration of advanced technology and superior craftsmanship. With its three-way configuration, cutting-edge sound dispersion technology, and solid build quality, it stands out as a premier choice for serious listeners. Whether used in a dedicated home theater or a high-end audio setup, the DD66000 promises to deliver an unrivaled listening experience, making it a worthy investment for those who demand the best in audio fidelity.