JBL DD66000 manual Passive Connecting Method, II. Bi-Wire Connecting Method

Page 27

Project EVEREST DD66000

bi-wire and bi-amp connections. Read the following explanations and connect in the suitable method.

I. Passive Connecting Method

The passive method requires one amplifier and one set of wires. Connections are made to either the upper terminals or the lower terminals . Do not remove the shorting straps.

II. Bi-Wire Connecting Method

The bi-wire connection method requires one amplifier and two sets of speaker wires. By removing the shorting straps, connections may be made to the individual network sections using four connectors, high frequency wires to the upper terminals and low frequency wires to the lower terminals.

III. Bi-Amp Connecting Method

The bi-amp connection method requires two amplifiers, one for the low frequency and one for the high frequency unit, and a crossover network. By removing the shorting straps, connections may be made in the following way. Wires from the high frequency amplifier are connected to the upper terminals, and wires from the low frequency amplifiers are connected to the lower terminals.

Project EVEREST DD66000 is shipped with twisted pair shorting straps installed. In case bi-wire or bi-amp connection method is to be employed, remove the straps from the terminals referring to figures below and retighten the terminals. If the amplifiers are connected to the Project EVEREST DD66000 loudspeakers in the bi-wire or bi-amp mode with the shorting straps still on, the amplifier outputs will be shorted which could result in costly amplifier damage when power is switched on.

∙In case shorting straps are used, make sure the conductors and sleeves of straps are firmly fastened by the terminals.

∙For safety and firm connection, cable termination with either spade or

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Project Everest DD66000 Users Guide Table of Contents Chapter Defining the Project Concept Project Everest DD66000 Page Project Everest DD66000 Chapter Project Everest DD66000 1501AL section view 1501AL Low Frequency Driver476Be section view 476Be High Frequency Compression Driver and HornPage 045Be-1 section view 045Be-1 Ultra-High Frequency Compression Driver and HornDD66000 system impedance Internal Crossover NetworkUnpacking the Project Everest DD66000 System Grille Removal Selecting Cable Amplifier Recommendations Placement and Set-up Considerations Floor Requirements System Orientation Project Everest DD66000 Switch OperationsHF Drive / LF Drive LF Level HF LevelBattery Installation Project Everest DD66000 Project Everest DD66000 Connections Passive Connecting Method II. Bi-Wire Connecting MethodIII. Bi-Amp Connecting Method Final Checklist Project Everest DD66000 Care and Maintenance Troubleshooting and Service Guide Project Everest DD66000 Register Project Everest DD66000 System Specifications USA JBL and Harman International

DD66000 specifications

The JBL DD66000 is a flagship model in the world of high-fidelity loudspeakers, designed to deliver an exceptional listening experience for audiophiles and music enthusiasts alike. With its rich heritage rooted in decades of acoustic engineering expertise, the DD66000 represents the pinnacle of JBL's commitment to superior audio performance.

One of the standout features of the DD66000 is its innovative three-way speaker configuration. This includes a 15-inch bass driver, a 4-inch midrange driver, and a high-frequency compression driver that produces crystal-clear treble. This arrangement allows for a wide frequency response, ensuring that every note, from the lowest lows to the highest highs, is reproduced with remarkable accuracy and detail.

The DD66000 boasts advanced technologies that enhance its performance. The Integrated Waveguide Technology ensures that sound is evenly distributed throughout the listening space, creating a spacious and immersive soundstage. This technology minimizes distortion and ensures that the sound maintains its clarity, even at high volumes. Additionally, the dual high-frequency compression drivers provide extended dynamic range, allowing the speaker to handle both quiet and loud passages seamlessly.

Another key characteristic of the JBL DD66000 is its robust build quality. The speaker is encased in an elegantly crafted cabinet that not only minimizes resonance but also adds to its aesthetic appeal. The sleek design incorporates high-quality materials, giving it a premium look that complements any audio setup.

The DD66000 is also versatile in its connectivity options. Designed to work seamlessly with various audio components, it features compatibility with both analog and digital sources. Audiophiles can enjoy their favorite music in high-resolution formats, ensuring that every detail is captured and enjoyed.

In summary, the JBL DD66000 is a masterful integration of advanced technology and superior craftsmanship. With its three-way configuration, cutting-edge sound dispersion technology, and solid build quality, it stands out as a premier choice for serious listeners. Whether used in a dedicated home theater or a high-end audio setup, the DD66000 promises to deliver an unrivaled listening experience, making it a worthy investment for those who demand the best in audio fidelity.
Top Page Image Contents