Hitachi CPX960WE Connection to the video signal terminals, Connection to the RGB signal terminal

Page 22

Connection to the video signal terminals

1. Input signals

	Brightness signal	1.0V p-p, 75	£2terminator
S-VIDEO signal		0.286V p-p(burst signal), 75 £2 terminator
	Color signal	0.286V p-p(burst signal), 75 £2 terminator
VIDEO	signal	1.0V p-p, 75	£2terminator
	Input	200mV rms,	20k £2or less (max. 3.0V p-p)
Audio	signal
	Output	0-200mVrms,	1k

2. Signal	input jacks
			Color	signal		Brightness signal
			Color	signal
			Ground			Ground
				S-VIDEO input (mini DIN 4-pin)
_Caution_	The	priority	sequence	of the	video input	jacks is as follows.
	(1)	S-VIDEO	input jack		(2) RCA	jack input jack
	When video signals are being projected, the audio input by the video is output to the audio
	output jack		(RGB/V1DEO).

Connection to the RGB signal terminal

1. Input signals

Video signal

Horizontal sync signal

Vertical sync signal

Compound sync signal

Input

Audio signal

Output

2. Signal input jacks

1Video input (red)

2Video input (green)

3Video input (blue)

4N.C

5N.C

6Ground (red)

7Ground (green)

8Ground (blue)

Analog, 0.7V p-p, 75 £2terminator (positive polarity) TTL level (positive/negative polarity)

TTL level (positive/negative polarity)

TTL level

200mV rms, 20k £2or less (max. 3.0V p-p)

O~200mVrms, 1k £2

9N.C

10 Ground

11 N.C

12 DDC jack (Display Data Channel)

13 Horizontal sync signal/compound sync signal

14 Vertical sync signal

15 DDC jack (Display Data Channel)

51

,0(OoOoOo&

1511

D-sub 15-pin shrink jack

22

Image 22

Contents Contents FeaturesOutline Page Before Use Avoid shock or impact on Do not install on an unstable surfaceProjector Do not position the power Cord under the projector. This can Do not allow the laser beam to enter EyesUse the caster brakes Do not touch the power plug with wet hands because thisWhen disconnecting Power plug, do not pull on the power Do not place heavy objects on this ProjectorMoving the projector Checking the package Contents Names and functions of each partNames and functions of each part Audio OUTVideo RGB Remote control transmitterP button *2 LaserBattery Cover TCaution Battery usage cautions BatteryCover Using the adjusters InstallationTypical LCD Projector and Screen Installation ToD view Side viewBasic operations To projectPlug & Play Turning off the powerPress the STANDBY/ON button for approximately 1 sec Freeze Cancelling the Freeze functionBasic operations Press the Freeze buttonMoving the display area Changing the magnification ratioReturning to normal display Adjustments and functions Returning to the initial settingsAdjustment item Adjustments and functionsUsing the Setup Menu Moves the image up and downSystem. When the screen is unstble no color Adjustment item Adjustment descriptionVideo Blank KeystoneStart UP Auto OFF TimerCOM. Speed Sync onInput signals Connection to the video signal terminalsConnection to the RGB signal terminal Signal Input jacksResolution Connectiontothe RGBsignalterminalExample of computer signal Signal mode Display ModeHorizontal signal timing Computer/Signal Timing Initial set signalsVertical signal timimg lines Connecting the USB Mouse Connection to the control signal terminalMouse functions Mouse cable Product name ModelSerial mouse Signal JackMouse RS232C communication 610Size Command Data ChartSystemvideo Color Balance RWhen data sent by the projector cannot be understood Requesting projector statusCleaning the Air filter Example of system setupFilterModel Lamp Screen displaysSymptom Possible cause When you think something wrongIndicators Message tableDimensional Diagram ControlAbout after-service About the warranty and after-serviceAbout the warranty About repairs during the warranty period