Hitachi CPX960WE user manual Message table, When you think something wrong, Indicators, Remedy

Message table (continued)

Indicators

The POWER indicator, LAMP

POWER		LAMP
indicator		indicator
Lights orange		Turns	off
Flashes	green	Turns	off
Lights	green	Turns	off
Flashes	orange	Turns	off

indicator and TEMP indicator light or blink in the following cases.

TEMP			Message	Processing	/
indicator
Turns	off	Standby	status
Turns	off	Warming	up
Turns	off	Operation	status ,1
Turns	off	Cool down

							Wait some time (approx. 20 min.) before
Lights	red	Lights	red	Turns	off	The lamp does not light. *2	turning the power on again, If the
							indicator still lights, the lamp may have
							failed and. Replace with a new lamp.
Lights	red	Flashes	red	Turns	off	A lamp has not been inserted	Firmly insert the lamp as far as possible
						or the lamp cover is missing,	and screw the lamp cover in place,
Lights	red	Turns	off	Flashes	red	The coolingfan is notoperating.	Contact	your	dealer,
Flashes	red	Flashes	red	Turns	off	The totallamp time has	Contact	your	dealer,
						exceededthe replacementtime.

When the LAMP e!' TEMP indicator lights or flashes, turn off the MAIN POWER switch before proceeding. If the problem still persists, contact your dealer or service company.

*1: When the cooling fan is stopped and the interior becomes overheated, the power will tam off automatically to allow cooling (the indicator will turn off). In such cases, turn offthe projector power, allow the set to cool and then tam the projector power on again. The lamp will then ligN. If the lamp does not light, contact your dealer or service company.

*2: In some cases, when the air holes becomes blocked and the interior temperature rises, the lamp will be turned off for protection and the LAMP iMicator will flash red. In such cases, turn offthe MAIN POWER switch, allow the set to cool (for approx. 20 min.) and then turn the power on again.

When you think something wrong

Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then

contact your dealer.

Symptom			Possible cause
The power is not		,The	main power switch is not turned on.
turned on.		,The	power cord is disconnected.
No video or audio.		,The	input is not correctly set.
		•No signal input.
Video is present	but	,The	projector is not correctly connected.
no audio.		,The	volume is seet to minimum.
		•Mute is turned on.
		•Audio is switched to Video when P in P is on.
Audio is present	but	,The	projector is not correctly connected.
no video.		,The	brightness adjustment knob is rotated
		fully	clockwise,
		•The	lens cap is still on.
Colorsare pale and		Color density and color matching are not
colormatching is poor.		correctly adjusted.
Images are dark.		,Brightnessandcontrastare notcorrectlyadjusted.
		•The lamp is nearing the endof its servicelife.
Video is blurred.		Focus or H PHASE is out of adjustment.
The LAMP indicator		Lamp failure.
lights red.
The TEMP indicator		Internal overheating.
lights red.

		Remedy	Page
,Tom on the main power switch.			P.13
,Plug the powercord into an AC poweroutlet.			P.9
,Use the	projector	or remote control to set.	P.8.10,
			13,19
,Connect	correctly.		P.9.31
,Connect	correctly.		P.9.31
,Press VOLUME + on the remote control or display			P.10.18
the menu screen and adjust the volume.
,Press the MUTE button.			P.8.10
,DisplaystheVolumebarandswitchestheAudioinput.			P.10
,Connect	correctly.		P.9.31
,Select BRIGHT with the MENU button and then			P.17
press the (@) ) key.
,Remove the lens cap.			P.13
Adjust the video.			P.18
,Adjust the video.			P.18
,Replace with a new lamp.			P.32
Adjust the focus or H PHASE.			P.13.18
Wait approximately		20 min. and then turn the	P.33
power on again.
,Make surethe ventilation openingsare notblocked.			P.31.32
,Clean the air filter.
•Lowertheambienttemperatureto 35degreesC orless.

A bright dot may be seen in the picture. This is a phenomenon peculiar to the liquid crystal and is not a problem.

33