Hitachi CP-X995W user manual Air Filters, Other Maintenance

Page 20

MAINTENANCE (continued)

Air Filters

Cleaning Air Filters

This projector uses 2 air filters. These air filters should be cleaned as described below at intervals of approximately 100 hours.

1.Switch the projector power supply OFF, and remove the power cord from the power outlet.

2.Remove the filter cover and the air filter.

3.Clean the air filter with a vacuum cleaner.

4.Set the air filter and the filter cover.

Replacing the Air Filter

filter cover

filters

ENGLISH

Replace the air filter if contamination cannot be removed, or if it is damaged.

1.Switch the projector power supply OFF, and remove the power cord from the power outlet.

2.Remove the filter cover and the old filter.

3.Set the new filter and the filter cover.

CAUTION • Switch power OFF and remove the power cord from the power outlet before beginning maintenance work. Please read the separate “SAFETY

INSTRUCTIONS” thoroughly to ensure that maintenance is performed correctly.

Replace the air filter if contamination cannot be removed, or if it is damaged. Contact your dealer in such case. For the optional air filter, see the item “Optional Parts” of the Table 12.

Do not use the equipment with the air filter removed.

When the air filter is clogged with dust etc. the power supply is switched OFF automatically to prevent the temperature rising inside the projector.

Other Maintenance

Maintenance Inside the Equipment

For safety reasons, ensure that the equipment is cleaned and checked by the dealer once every two years. Maintaining the equipment by yourself is dangerous.

Cleaning the Lens

Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.

Cleaning the Cabinet and Remote control transmitter

Gently wipe with a soft cloth. If dirt and stains etc. are not easily removed, use a soft cloth dampened with water, or water and a neutral detergent, and wipe dry with a soft, dry cloth.

CAUTION • Switch power OFF and remove the power cord from the power outlet before beginning maintenance work. Please read the separate “SAFETY

INSTRUCTIONS” thoroughly to ensure that maintenance is performed correctly.

Do not use detergents or chemicals other than those noted above (e.g. benzene or thinners).

Do not use cleaning sprays.

Do not rub with hard materials, or tap the equipment.

NOTE When this projector is brought into a warm room from a cold outdoor, condensation can take place on the projection lens and mirror inside, blurring the screen and reducing your eyesight, but do not worry. The condensation will disappear and the screen will return to a normal condition no sooner than the projector acclimates to the surrounding temperature.

ENGLISH-19

Image 20
Contents CP-X990W / CP-X995W Contents Before USE FeaturesContents of package Before USE Part NamesENGLISH-4 Loading the Batteries Installation Installation of the Projector and ScreenAngle Adjustment Installation ReferenceCabling InstallationCabling Plug & Play Power ConnectionExample of System Setup Power on Power OFFOperations StandbyBasic Operation Description OperationsBasic Operation Select Mode of P.IN P. Display Press the PinP button Set / Clear Keystone Mode Press the Keystone buttonNormal menu Single menu Menu Display Start/Stop Press the Menu buttonSetup Menu Setup MenuInput Menu Input Menu DescriptionRGB BlackImage Menu Image Menu DescriptionMyScreen MirrorOptions Menu Options MenuSelect Menu Background Color Select with Operation Start/Stop PressNo Signal Menu No Signal MenuLamp Life MaintenanceLamp Replacing the Lamp MaintenanceResetting the Lamp Timer Other Maintenance Air FiltersTroubleshooting Message ContentsOSD Message OSD MessageTroubleshooting Indicators MessageIndicators Message IndicatorSymptom Possible cause Remedy SymptomSymptom Specifications SpecificationsWarranty and AFTER-SERVICE Technical Dimension DiagramSignal Connector Pin Assignment Example of computer signal TechnicalInitial set signals Connection to the Mouse Control PS/2, ADB or Serial MouseUSB Mouse PS/2 MouseADB Mouse Serial MouseCommunications setting Command dataRS-232C communication ProtocolRequesting projector status Get command Changing the projector settings Set commandUsing the projector default settings Reset Command Increasing the projector setting value Increment commandCRC Be EF BA D2 Be EF FD D3 Be EF Ntsc PAL RGB Be EF For the Customers in Canada Pour les utilisateurs au Canada Regulatory NoticesFCC Statement Warning Hitachi Europe GmbH Hitachi Sales Europe GmbHHitachi Business Systems Nordic Hitachi France
Related manuals
Manual 39 pages 2.17 Kb