Hitachi IPJ-AW250NM Turning on the MyScreen Password, Turning off the MyScreen Password

Page 74
ENTER PASSWORD box
(large)
ENTER NEW PASSWORD
box (small)

SECURITY menu

Item

Description

MyScreen

PASSWORD

The MyScreen PASSWORD function can be used to prohibit access to the MyScreen function and prevent the currently registered MyScreen image from being overwritten.

1 Turning on the MyScreen PASSWORD

1-1 Use the ▲/▼ buttons on the SECURITY menu to select MyScreen PASSWORD and press the ► button to display the MyScreen PASSWORD on/ off menu.

1-2 Use the ▲/▼ buttons on the MyScreen PASSWORD on/off menu to select ON. The ENTER NEW PASSWORD box (small) will be displayed.

1-3 Use the ▲/▼/◄/► buttons to enter the password. Move the cursor to the right side of the ENTER NEW PASSWORD box (small) and press the ► button to display the NEW PASSWORD AGAIN box, enter the same PASSWORD again.

1-4 Move the cursor to the right side of the NEW PASSWORD AGAIN box and press the ► button to display the NOTE NEW PASSWORD box for about 30 seconds, please make note of the password during this time.

Pressing the ENTER button on the remote control or ► button on the projector will return to MyScreen PASSWORD on/off menu.

When a password is set for MyScreen:

•The MyScreen registration function (and menu) will be unavailable.

•The MyScreen Lock menu will be unavailable.

•The START UP setting will be locked on MyScreen (and the menu will be unavailable).

Turning the MyScreen PASSWORD off will allow normal operation of these functions.

•Please do not forget your MyScreen PASSWORD.

2 Turning off the MyScreen PASSWORD

2-1 Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off menu.

2-2 Select OFF to display the ENTER PASSWORD box (large). Enter the registered password and the screen will return to the MyScreen PASSWORD on/off menu.

If an incorrect PASSWORD is input, the menu will close. If necessary, repeat the process from 2-1.

3 If you have forgotten your password

3-1 Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off menu.

3-2 Select OFF to display the ENTER PASSWORD box (large). The 10 digit Inquiring Code will be displayed inside the box.

3-3 Contact your dealer with the 10 digit Inquiring Code. Your password will be sent after your user registration information is confirmed.

(continued on next page)

74

Page 73 Page 75
Image 74
Page 73 Page 75
Contents
Thank you for purchasing this projector About this manualProjector Trademark acknowledgmentContents Features Checking the contents of packageHOT Part namesProjector LargeHdmi Computer IN2 Control panel STANDBY/ON buttonButtons Focus +/- buttons 1415MY Button 1 button MY Button 2 button Keystone button Down button Volume + buttonComputer button Zoom button Zoom + button Position button 26Setting up ArrangementArrangement Connecting with your devices About Plug-and-Play capability VCR/DVD/Blu-ray Disc Player ComputerConnecting with your devices Monitor Microphone system USB storage DeviceAccess point Computer HdmiSecurity bar Anti-theft chain or wire Connecting to a power supplyUsing the security bar and slot Security slotUsing the cable cover About the remote control signal Remote controlInstalling the batteries Hitachi MAXELL, Part No.LR6 or R6PUSB Type B port Changing the frequency of remote control signalUsing as a simple PC mouse & keyboard Exchanging the tip of the pen Installing the batteryInteractive pen Hitachi MAXELL, Part No. LR03STANDBY/ON button Power indicator Power on/offTurning on the power Turning off the power Operating Adjusting the volumeSelecting an input signal Temporarily muting the soundVideo button Press the MY Source / DOC. Camera button onComputer button MY SourceFor an Hdmitm signal Searching an input signalFor a computer signal Selecting an aspect ratioZoom button Adjusting the projectors elevatorAdjusting the zoom and focus Zoom + buttonFor a component video signal Using the automatic adjustment featureFor a video signal and s-video signal Focus buttonPosition button Adjusting the positionCorrecting the keystone distortions Keystone buttonUsing the magnify feature Magnify ON/OFF buttonFreeze button Temporarily freezing the screenTemporarily blanking the screen Blank buttonAdvanced Menu Using the menu functionESC button Reset button Enter buttonIndication in OSD On Screen Display Indication MeaningAspect DescriptionInteractive ZoomReset Picture ModeECO Mode MirrorInteractive menu Contrast Picture menuBrightness GammaCustom Custom MIDLOW ColorOFF SharpnessPresentation Active IrisImage menu For a computer signalFor an Hdmitm signal Position Signal, the range of this adjustment depends on Over ScanSelected will reset the H Position to the default setting USB Type B or Hdmi portSize PhaseAuto Adjust ExecuteHigh MID LOW Input menuTV Film OFF Video NRHdmi Range Video FormatHdmi Format Frame Lock Auto Sync on G OFFComputer Resolution Left MID Right Setup menuShift No Input is Detected Sync is OUT of Range Invalid Scan FreqPerfect FIT Input button On OFFNormal Saving Normal ECONormal Hinvert Vinvert Speaker VolumeAudio menu Audio SourceMIC Level MIC VolumeHdmi Audio High LOWScreen menu English Français Deutsch EspañolMyScreen registration is finished Capturing error has occurred. Please try againMyScreen MyScreen Lock MessageSource Name Template Mode Description Closed CaptionDisplay ChannelComputer IN2 LAN USB Type a Video Video Hdmi USB Type B Direct PowerOption menu Mouse USB Display Auto PowerOFF USB Type BLamp Time Cancel OKCancel MY Button No Messenger Data appearsZoom Turns the D-ZOOM mode on/off. When the D-ZOOM Active Iris Changes the active iris modePicture Mode Changes the Picture Mode Mode is on, use the / cursor buttons to adjustGhost ServiceFAN Speed Filter MessageLens Door Open KEY LockLens Door Lock Lens Door CloseControl port Remote Freq1NORMAL 2HIGH Communication Type Serial SettingsBaud Rate Service ParityResponse Limit Time Transmission MethodFactory Reset InformationDhcp SetupNetwork menu IP Address DefaultSetup Gateway SubnetProjector Name MY Image AMX D.D Presentation Quit Presenter User Name Section SwitchingMulti PC Guide Enter to the Security menu PasswordSecurity menu SecurityMyScreen Turning on the MyScreen PasswordTurning off the MyScreen Password Turning off the PIN Lock PIN LockTurning on the PIN Lock If you have forgotten your PIN codeTurning off the Transition Detector Transition DetectorTurning on the Transition Detector Turning off the MY Text Password MY Text PasswordTurning on the MY Text Password MY Text WritingSystem requirements Presentation toolsInteractive Function ApplicationInteractive Function Connection during use Using the pen Preliminary preparationBasic pen operation Customizing the penUsing StarBoard Software Supported format PC-LESS PresentationSupported storage media Supported file formatThumbnail mode Thumbnail menu Selected image Thumbnail imagesDown Setup menu for the selected imageOperating by buttons or keys Enter InputOperating by the menu on the Thumbnail screen PC-LESS Presentation Full Screen Mode Slideshow mode Control Projector SoftwarePlay Playlist Example of playlist.txt filesUSB Port USB cable 1 piece USB DisplayHardware and software requirement for computer Right-Click menu Floating menuOptions window Type number DT01181 MaintenanceReplacing the lamp Replacing the lampHigh Voltage High Temperature Lamp warningStitched side On next Cleaning and replacing the air filterType number UX37191 Filter set Cleaning and replacing the air filter 100101 Replacing the internal clock batteryHitachi MAXELL, part number CR2032 or CR2032H Cleaning cloth 102Maintenance of the pen Caring for the cabinet and remote controlMaintenance of the pen sensors horns Inside of the projectorOther care 104An improper signal is input TroubleshootingThere is no input signal Related messages106 Internal temperature is risingButton operation is not available Regarding the indicator lamps Has become heated It is time to clean the air filterThere is a possibility that the interior portion Lens door is not opened properlyResetting all settings Audio SOURCE/SPEAKER setting is not correct Signal cables are not correctly connectedVolume is adjusted to an extremely low level Mode selected for Hdmi Audio is not suitableProjector is operating in Eco mode Color settings are not correctly adjustedColor Space setting is not suitable Frame Lock function cannot work on the current Input signalCommunication Type for the Control port is Computer cannot start up in the current hardwareSaving function is working Set to Network BridgeIs the USB cable connected correctly? Is the use of USB cables disabled?Is the power of the projector turned on? Is the system started up in the correct sequence?Are you using more than one pen at the same time? This may be due to poor contact of the batteryHas the battery run out? Is the volume from the speaker of the projector too loud?Is alignment of the pen position correctly performed? StarBoard Software files may be corrupted, orIs the tip of the pen worn out? Is the projector inclined?Is the computer image projected within the area Screen? Is the projector correctly installed?Is a part of the image enlarged using the Magnify Function? 117 SpecificationsEnd User License Agreement for the Projector Software
Related manuals
Manual 2 pages 39.75 Kb
Top Page Image Contents