Hitachi CP-X935E Be careful in handling the power cord, Do not block the ventilation holes

Page 5
Pull out the power plug from the power outlet.

Warning

Be careful in handling the power cord.

Do not scratch, damage or process the power cord. Do not bend it forcibly. Also do not put a heavy object on it, do not heat it and do not pull it. If you do, the power cord may be damaged and it may cause a fire, electric shock, etc.

Do not pull the cord.

Do not put a heavy object on it.

Do not damage the cord.

Do not put it near a heating

device.

Be careful that this unit is not placed

on the power cord. The power cord may be damaged and it may cause a fire, electric shock, etc. If the cord is covered with a carpet, etc. a heavy object may be put on it without your realizing it.

If the cord is damaged (core wire is exposed, disconnected, etc.), ask

your dealer to replace it. It may cause a fire, electric shock, etc.

Check that no dirt adheres to the

power plug and fully insert without any play. If dirt adheres or the connection is incomplete, it may cause a fire, electric shock, etc.

The outer shield of power cord must be connected to ground.

If you do not, it may cause a electric shock.

ENGLISH

Caution

Do not step on this unit or do not put a

heavy object on it.

Do not step on this unit. Especially pay attention if children are present. If you do, the unit may fall over or may be broken causing an injury.

Do not put a heavy object on this unit. If you do, the unit may fall due to its imbalance or it may drop, causing an injury.

Do not block the ventilation holes.

Do not block the ventilation holes. If the ventilation holes are blocked, the heat inside may build up and it may cause a fire. Do not use this unit in the following ways: On its side. In a poorly ventilated, narrow place. On a carpet or bedspread. Covered with a tablecloth. Place this unit so that the ventilation holes are kept 50cm or more away from the wall.

Cleaning

Be sure to pull out the power plug

 

from the power outlet for safety

Pull out the power

when cleaning.

plug from the

power outlet.

Set the caster stoppers.

When this unit is installed on the table with casters, set the caster stoppers. If the table moves, it may fall over, causing an injury.

Do not place this unit in a moist or dusty place.

Do not place this unit in a moist or dusty place. It may cause a fire, electric shock, etc.

Do not place this unit where it would be exposed to soot or steam, near a cooking stove or humidifier, etc. It may cause a fire, electric shock, etc.

Handle the power cord carefully.

Do not bring the power cord near a heating device. The shield of the cord may melt and it may cause a fire, electric shock, etc.

Do not insert / disconnect the power plug with wet hands. It may cause an electric shock.

When the power plug is to be disconnected, do not pull the power cord. The power cord may be damaged and it may cause a fire, electric shock, etc. Be sure to hold the power plug.

Caution when carrying it.

When this unit is to be moved, apply a cover to the lens and be sure to disconnect the power plug from the power outlet and check that all external connection cords are removed before moving it. If not, the cord may be damaged and it may cause a fire, electric shock, etc.

5

Downloaded from www.Manualslib.com manuals search engine

Image 5
Contents Contents FeaturesOutline Operating GuideFor the Customers in U.K Power cord Video signal cablesBefore use Instructions to UsersDo not install this unit in an unstable place Do not look directly at the lens when Lamp is litDo not use power supplies other Than that specified If any abnormality occursCleaning Be careful in handling the power cordHandle the power cord carefully Do not step on this unit or do not put a Heavy object on itClean inside the unit at least once two years When you are not going to use For a long timeDo not place this unit where it gets hot VolumeNames and functions of each part Contents of shipping boxRGB/VIDEO Disk PAD Remote control transmitterLaser Aperture Names and functions of each partHow to use foot adjusters InstallationExample of the projector and screen installation Basic operations ∙ The on indicator will light up orangeTo project the picture For 3 secondsIndicator lights up orange To turn off the powerStandby mode PLUG&PLAYMagnifying Function Freeze FunctionTo return to the initial setting Adjustments and functionsMemory function ∙ On-screen menus are displayed on the screenManual Operation SET UPHow to use the SET UP menu During AUTO-adjustment Auto-adjustmentInput Auto Confirm ScreenOPT ImageBlank RevealConnection to the RGB signal terminal Connection to the video signal terminalsText Example of computer signalResolution Standard Display Dots KHz Computer/signal Horizontal Timing µs Initial set signalsComputer/signal Vertical Timing lines Horizontal Timing µsControl signal terminal Connection to the control signal terminalSerial mouse PS/2 mouseADB Mac mouse Control command table Control command tableCommunication RS232C cable ReferenceControl data table Auto AdjustVideo System Color BalanceProcedure of setting the Projector status Procedure of getting the Projector statusProcedure of default setting the Projector status Example of command errorConnecting various equipment Example of system setupAC Inlet Computer Note type ComputerDesk typeAir filter Cleaning the air filterRemove the lamp cover How to replace lampLamp Option lamp Lamp unit CP-X935W/E DT00201Action MessageBlink in the following cases Message tableVideo Dimension diagramAudio Batteries LR6