Hitachi CP-X935E specifications For the Customers in U.K

Page 2

FOR THE CUSTOMERS IN U.K

THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U.K PLEASE REFER TO THE NOTES ON THIS PAGE.

IMPORTANT FOR UNITED KINGDOM

WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND LABELS

The mains lead on this equipment is supplied with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA or BSI approved BS 1362 fuse must be used of the same rating. If the fuse cover is detachable never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug. Fuse covers are available from your dealer.

DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.

Should it be necessary to change the mains plugs, this must be carried out by a competent person, preferable a qualified electrician.

If there is no alternative to cutting off the mains plug, ensure that you dispose of it immediately, having first removed the fuse, to avoid a possible shock hazard by inadvertent connection to the mains supply.

WARNING: THIS EQUIPMENT MUST BE EARTHED

IMPORTANT:

The wires in the mains lead are coloured in accordance with the following code:

Green and Yellow=Earth, Blue=Neutral, Brown=Live.

Green & Yellow to Earth

Brown to Live

 

Fuse

Blue to Neutral

Cord Clamp

As these colours may not correspond with the coloured makings identifying the terminals in your plug, proceed as follows:

The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is

marked with the letter E or by the earth symbol

 

 

or coloured Green or Green and Yellow.

 

 

 

 

The wire coloured Blue must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.

2

Downloaded from www.Manualslib.com manuals search engine

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Outline FeaturesContents Operating GuideFor the Customers in U.K Before use Video signal cablesPower cord Instructions to UsersDo not use power supplies other Than that specified Do not look directly at the lens when Lamp is litDo not install this unit in an unstable place If any abnormality occursHandle the power cord carefully Be careful in handling the power cordCleaning Do not step on this unit or do not put a Heavy object on itDo not place this unit where it gets hot When you are not going to use For a long timeClean inside the unit at least once two years VolumeContents of shipping box Names and functions of each partRGB/VIDEO Remote control transmitter Disk PADNames and functions of each part Laser ApertureHow to use foot adjusters InstallationExample of the projector and screen installation To project the picture ∙ The on indicator will light up orangeBasic operations For 3 secondsStandby mode To turn off the powerIndicator lights up orange PLUG&PLAYFreeze Function Magnifying FunctionMemory function Adjustments and functionsTo return to the initial setting ∙ On-screen menus are displayed on the screenManual Operation SET UPHow to use the SET UP menu Input Auto-adjustmentDuring AUTO-adjustment Auto Confirm ScreenBlank ImageOPT RevealConnection to the video signal terminals Connection to the RGB signal terminalText Example of computer signalResolution Standard Display Dots KHz Computer/signal Vertical Timing lines Initial set signalsComputer/signal Horizontal Timing µs Horizontal Timing µsConnection to the control signal terminal Control signal terminalSerial mouse PS/2 mouseADB Mac mouse Communication Control command tableControl command table RS232C cable ReferenceVideo System Auto AdjustControl data table Color BalanceProcedure of default setting the Projector status Procedure of getting the Projector statusProcedure of setting the Projector status Example of command errorAC Inlet Computer Note type Example of system setupConnecting various equipment ComputerDesk typeCleaning the air filter Air filterLamp How to replace lampRemove the lamp cover Option lamp Lamp unit CP-X935W/E DT00201Message ActionMessage table Blink in the following casesAudio Dimension diagramVideo Batteries LR6
Top Page Image Contents