Hitachi CP-X935E specifications Message, Action

Page 30

Lamp (continued)

5

Install the lamp cover and fix it using screws.

￿ To prevent burn, install the lamp cover and secure it using the screws.

 

￿ Do not turn on the power with lamp cover removed.

 

Lamp cover

 

 

 

Whenever the lamp is replaced, reset the total operation time of the lamp.

Do not reset if the lamp has not been replaced.

Screw

2. Reset the lamp time

Pleasecarry out the following operationwithin 10 minutes from power on, if you replacedthe lamp after

2,000 hours.

MAGNIFY VOLUME

3

2

OFF

 

 

 

 

POSITION ON

LASER

 

 

STANDBY/ON

 

 

 

 

 

 

 

 

INPUT

 

 

 

 

MUTE

 

 

1

 

MENU

RESET

RIGHT

 

3

MENU ON

MOUSE ON

1, 2

 

 

 

RESET

BLANK

TIMER

 

 

RGB

VIDEO

 

 

 

INPUT

 

 

 

1)Pressthe RESET button on projector for 3 secondsor remote control TIMER button for 3 seconds and display the total lamp used time.

￿When accumulatedoperation time of the lamp reaches1700 hours, the following display will appear at the bottom of the screen.

2)Pressthe RESET button on projector or remote control MENU ON button during displaying the lamp used time.

3)Select the ￿0￿ on the screen using the MENU () button or DISK PAD.

LAMP 1700 h

LAMP 1700 ￿￿♦ 0 ￿¡CANCEL

Message table

On-screen display

The following messages are displayed on the screen.

MESSAGE

Action

 

 

CHANGE THE LAMP

Accumulated operation of lamp has exceeded 1,700 hours. It is recommended

AFTER REPLACING LAMP,

to replace lamp. Replace with new lamp. If accumulated operation reaches

RESET THE LAMP TIMER.

2,000 hours, lamp will automatically turn off. * 1

CHANGE THE LAMP

Lamp has 1,979 hours on it.

AFTER REPLACING LAMP,

Call a maintenance person. * 1

RESET THE LAMP TIMER.

Time is 20 ~ 0. (count down.)

THE POWER WILL TURN

 

OFF AFTER 20 Hr.

 

 

 

Blinking of

When the lamp has 2,000 hours or more on it, the message will blink, and the

CHANGE THE LAMP

power will turns off after 10 minutes.* 2

 

 

NO INPUT IS DETECTED

Signal is hot input. (See page 19, 20)

 

 

SYNC IS OUT OF RANGE

The horizontal frequency of the input signal exceeds the range of the projector,

it cannot be displayed. (See page 20, 21)

 

 

 

*1 This message are not displayed after 3 minutes.

But this message are displayed when you turn on the power again.

*2 It is possible to again turn on the power, however the power will go off after about 10 minutes.

Downloaded from www.Manualslib.com manuals search engine

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Outline FeaturesContents Operating GuideFor the Customers in U.K Before use Video signal cablesPower cord Instructions to UsersDo not use power supplies other Than that specified Do not look directly at the lens when Lamp is litDo not install this unit in an unstable place If any abnormality occursHandle the power cord carefully Be careful in handling the power cordCleaning Do not step on this unit or do not put a Heavy object on itDo not place this unit where it gets hot When you are not going to use For a long timeClean inside the unit at least once two years VolumeContents of shipping box Names and functions of each partRGB/VIDEO Remote control transmitter Disk PADNames and functions of each part Laser ApertureInstallation Example of the projector and screen installationHow to use foot adjusters To project the picture ∙ The on indicator will light up orangeBasic operations For 3 secondsStandby mode To turn off the powerIndicator lights up orange PLUG&PLAYFreeze Function Magnifying FunctionMemory function Adjustments and functionsTo return to the initial setting ∙ On-screen menus are displayed on the screenSET UP How to use the SET UP menuManual Operation Input Auto-adjustmentDuring AUTO-adjustment Auto Confirm ScreenBlank ImageOPT RevealConnection to the video signal terminals Connection to the RGB signal terminalExample of computer signal Resolution Standard Display Dots KHzText Computer/signal Vertical Timing lines Initial set signalsComputer/signal Horizontal Timing µs Horizontal Timing µsConnection to the control signal terminal Control signal terminalPS/2 mouse ADB Mac mouseSerial mouse Communication Control command tableControl command table RS232C cable ReferenceVideo System Auto AdjustControl data table Color BalanceProcedure of default setting the Projector status Procedure of getting the Projector statusProcedure of setting the Projector status Example of command errorAC Inlet Computer Note type Example of system setupConnecting various equipment ComputerDesk typeCleaning the air filter Air filterLamp How to replace lampRemove the lamp cover Option lamp Lamp unit CP-X935W/E DT00201Message ActionMessage table Blink in the following casesAudio Dimension diagramVideo Batteries LR6
Top Page Image Contents