Epson E02 manual Installation Precautions

Page 17

UB-E02 Technical Reference Guide

Chapter 2

Installation

2.1 Installation Precautions

WARNING

❏Before installing, disconnect the Power Unit from the TM Printer (as well as turning the power switch off).

Even when the power switch is off, voltage is still present at some points on the circuit board. Changing components while the Power Unit is connected can cause damage to the UB-E02 and the printer.

❏A grounded wrist strap should be worn during installation, to avoid damage from static electricity.

❏To avoid damage from static electricity when the unit is removed, place it on an static-safe surface such as conductive foam.

❏Protect the unit from vibration and shock that could damage to the unit.

❏Be careful to avoid dropping conductive objects such as paper clips on the circuit board, as they could short circuit connections and cause damage from excessive current.

❏This product should only be connected to the devices specified in this guide. Connecting other devices could cause damage, fire or explosion.

❏Do not attempt to wire this product other than as described in this document. Improper wiring could cause damage, fire or explosion.

❏Never disassemble or modify this product. Tampering with this product may result in injury, fire, or electric shock.

❏Do not use in locations subject to high temperature, humidity or dust levels. Excessive temperature, humidity or dust may cause equipment damage, fire, or shock.

❏Never connect a public telephone line to the modular connector on this product.

❏Parts on the circuit board may become hot during operation. Therefore, wait approximately 10 minutes after turning the power off before touching them.

❏To prevent the possibility of electrical shock, do not perform installation or connect cables during a thunderstorm.

Rev. A

Installation 2-1

Image 17

Contents UB-E02 Technical Reference Guide Page Rev. a Revision Information Related Documents Contents of the GuideAbout This Guide CE Marking EMC and Safety Standards AppliedFCC Compliance Statement For American Users For Canadian UsersGereäuschpegel Key to SymbolsLabel Safety PrecautionsProduct Servicing Introduction Environments for Setup UtilityOperating Environments Supported Operating SystemsSupported TM Printers Installation Overview How to Use this GuideProgramming AppendixContents Rev. a Contents Xii Contents Rev. a Supported Network Protocols Supported Operating SystemsOther Limitations Installation Precautions InstallationUnpacking SwitchPart Names FunctionsUB-E02 Installation 4Installation Rev. a Page 6Installation Rev. a UB-E02 Status Sheet Printing Initializing UB-E023 Q3. Starting up the printer takes a long time FAQ2 Q2. The self test does not operate correctly UB-E02 Technical Reference Guide 10Installation Rev. a Setting the TCP/IP protocol in Your Operating System Setting the IP AddressSetting the IP Address using Epson TMNet WinConfig Windows UB-E02 Technical Reference Guide Windows NT Windows Installation Environments Installing Epson TMNet WinConfigInstallation with Windows Setting with the Epson TMNet WinConfig UB-E02 Technical Reference Guide Page Setting the IP Address Using the arp/ping Command Example ping Epson TMNet WinConfig Functions Menu Bar Tool Menu Time-out settingSearch Options Settings Printer Print server TCP/IP Password Opening Screen Epson TMNet WebConfig FunctionsTCP/IP General Information Protocol Information and SettingsApipa 2.2 TCP/IP InformationSnmp Information 2.4 TCP/IP Setting Snmp Communication Setting Snmp IP Trap 1 Setting Snmp IP Trap 2 Setting Administrator Setting Password Setting Reset Advanced Programming Samples Buffer of the UB-E02 Method of Printing to the UB-E02For Windows Console Direct Printing by PORT91004Programming Samples For Linux Monitoring of the ASB status Commands Sent to a TM Printer When the Power is OnPriorities of Printing Time-out for ConnectionCommands Packets Printer Operation by the UDP CommandsReply data 2 03-0000 Retrieving Basic Information3 03-0010 Retrieving Status Set-up data 5 03-0012 Reset4 03-0011 Forced Transmission 6 03-0013 Buffer Flash 7 03-0016 Clearing Connection Time-Out TimerFor Windows Console Programming Sample12Programming Samples Rev. a 13Programming Samples For Linux14Programming Samples Printer Connection FeaturesLine Display Connection OverviewHardware Specifications External appearance and connector locations Software SpecificationsBasic Communications Protocols Printing Communications ProtocolsSnmp MIB Status Inquiry and Setting ProtocolsHttp IP Address Acquisition by Dhcp Automatic IP Address Assignment ProtocolsEnpc IP Address Assignment by Apipa Manual SettingItem List Internal SettingsSetting with Exclusive utility Internal Parameter Setting MethodsSetting with Browser Setting the IP Address with arp + pingInitializing Upgrade MethodsVersion Upgrading Supported protocolStorage Conditions Environmental SpecificationsDefinitions 2Definitions Rev. a Page Epson