Epson EMP-30 manual Loosen the two lamp fixing screws, Take out the lamp, Install the new lamp

Page 49

Procedure

1

2

3

4

5

6

Cleaning

Replacing Consumables

Turn off the projector power, wait for the cool-down period to end, and then disconnect the power cable.

The cool-down period lasts for about 20 seconds. The actual time will vary depending on the external air temperature.

Wait until the lamp has cooled down, and then remove the lamp cover from the base of the projector.

It takes approximately one hour for the lamp to cool down by itself after the cool-down period has finished.

Put your finger into the recess, and pull straight out to remove the lamp cover.

Loosen the two lamp fixing screws.

Use the screwdriver that is supplied with the spare lamp or a Phillips screwdriver to loosen the two lamp fixing screws that are securing the lamp to the projector.

Take out the lamp.

Hold the lamp by the two tabs to lift it up and out from the projector.

If the lamp is broken replace by a new lamp, or contact your local dealer for further advise.

If replacing the lamp yourself, be careful to avoid pieces of broken glass.

(Projection cannot be carried out until the lamp is replaced.)

Install the new lamp.

Hold the lamp so that it faces the correct way to fit into the projector, and then insert the lamp and tighten the two lamp fixing screws.

Install the lamp cover.

Appendices

Slide the cover in from the outside, and then push

 

it in until it clicks into place.

 

47

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Page General information About the Manuals and Notations UsedMeaning of unit and projector Contents Epson cinema filter function Features of the ProjectorPage Page Adjusting the Image Quality Turning Off the Projector Adjusting the Screen ImageTurning On the Projector Turning On the Projector Connecting the Power CableBasic Operations Turning On the Power and Projecting ImagesIBM Turning On the ProjectorTurning Off the Projector Attach the lens cover Retract the front adjustable feet if they are extendedTurning Off the Projector Adjusting the Image Size Adjusting the Screen ImageFocusing the Screen Image Turn the focus ring to adjust the image focusAdjusting the Screen Image Adjusting the Image AngleSeen from the side Seen from above Approx º above Approx º below Correcting Keystone DistortionUsing the Epson Cinema Filter Adjusting the Image QualityAttach the accessory Epson cinema Quality of the screen images can be adjusted as followsOperations Selecting the Colour ModeBasic Automatic Setup Adjusting Computer ImagesAdjusting the Image Quality Press the and buttons to set the tracking value Adjusting the TrackingPress the and buttons to set the sync value Adjusting the SyncUseful Functions When a Computer is Connected Using the Configuration Menu FunctionsVideo Menu Sub-menu Function Default Using the Configuration Menu FunctionsVideo Menu Video S-Video, Composite video, ComponentSub-menu Function Default Settings and Useful FunctionsComputer Analogue-RGB/RGB video Using the Configuration Menu FunctionsSignal is being input Setting MenuAudio Menu BlueAdvanced Menu Using the Configuration Menu Functions Sub-menu DefaultImages are horizontally and vertically reversed Reset Settings and UsefulLanguage setting to their default settings About MenuReset All Menu Select a menu item Using the Configuration MenusConfirm the selection Select a sub-menu itemSelect other menu items in the same way Select a setting valueClose the menu Remote control Useful Functions When a Computer is ConnectedMute FreezeUseful Functions When a Computer is Connected Press the E-Zoom button on the remote controlZoom When the Indicators Provide No Help Using the Help When Having Some TroubleUsing the Help Troubleshooting When Having Some TroubleCause Remedy or Status When Having Some Trouble Power IndicatorStatus Cause Remedy or Status See Status Cause Remedy or StatusWhen the Indicators Provide No Help Has the front adjustable feet been adjusted Is the power for the video source or computer turned on?Condition Poor image quality out of focus or distorted Is the lens cover still attached?When connected to a computer Position been adjusted correctly?Has the correct resolution been selected? Probable cause Remedy Is the Zoom button setting correct?Has the colour been adjusted correctly? Has the image contrast been adjustedHave the colour intensity and tint been adjusted correctly? Is the lamp due for replacement?Attached to the projectors lens? Is the accessory Epson cinema filter stillHas the correct audio input port been Selected?Remote control does not work Minimum setting?Is the remote control too far from the projector? Has the battery insulating tape beenProbable cause Remedy Cooling fan does not stop Page Optional Accessories List of Supported Monitor Displays MaintenanceSpecifications Appearance Part Names and Functions Glossary IndexCleaning MaintenanceCleaning the Projector Case Cleaning the Lens and Epson Cinema FilterRemove the battery holder Inserting the BatteryRemove the old battery and insert the new battery Replacing ConsumablesMaintenance Lamp Replacement PeriodReplacing the Lamp It is time to replace the lamp whenInstall the lamp cover Install the new lampLoosen the two lamp fixing screws Take out the lampConnect the power cable, and then Resetting the Lamp Operating TimeConfiguration menu will be displayed Replacing the Air Filter Optional Accessories Component Video Input/RGB Video Input List of Supported Monitor DisplaysComposite Video/S-Video Input ComputerSpecifications USA SafetyAppearance Receives signals from the remote control Adjusts the image focusPart Names and Functions Front/TopLeft Side Control PanelPart Names and Functions Base RearRemote Control Glossary Video Glossary SRGBSync SynchronisationGeneral Terms IndexUsing the Configuration Menu Functions Remote control light-receiving areaIndex Rear ProjDeclaration of Conformity FCC Compliance Statement For United States Users EPSON/SEIKO Epson Corporation Printed on 100% recycled paper

EMP-30 specifications

The Epson EMP-30 is a portable projector that has garnered attention for its performance and versatility. Designed for both business presentations and home entertainment, the EMP-30 balances features that cater to a variety of users.

One of the standout characteristics of the Epson EMP-30 is its brightness. It offers a brightness level of 2,500 ANSI lumens, making it suitable for use in both well-lit and dim environments. This feature ensures that images remain clear and vibrant, even under challenging lighting conditions. The resolution of the projector stands at XGA (1024 x 768), which is ideal for standard presentations and displays. This high resolution ensures text and images are sharp, making it easier to engage an audience.

The EMP-30 uses 3LCD technology, which is known for producing vivid colors and consistent image quality. Unlike traditional projectors that rely on a single light source, 3LCD utilizes three separate liquid crystal panels to project red, green, and blue light simultaneously. This results in enhanced color accuracy and a broader color gamut, which is particularly noticeable in presentations featuring detailed graphics or videos.

Portability is another key feature of the Epson EMP-30. Weighing around 2.8 kg, it is lightweight enough to be transported easily between home, office, or educational environments. The compact design makes it user-friendly, allowing for quick setups in various locations.

Connectivity options are plentiful, including VGA, composite, and S-video inputs, enabling compatibility with a wide array of devices such as laptops, DVD players, and gaming consoles. The EMP-30 also features an audio output to connect external speakers for improved sound quality during presentations or movie screenings.

Another notable characteristic is its lamp longevity. The ECO mode extends the lamp life up to 5,000 hours, reducing maintenance costs and the frequency of replacements.

Additionally, the EMP-30 offers convenient features such as automatic vertical keystone correction, ensuring that images are displayed correctly even if the projector is angled. The user-friendly interface simplifies operation, making it accessible for users of all experience levels.

In conclusion, the Epson EMP-30 stands out as a versatile and reliable projector suitable for various applications. With its brightness, advanced 3LCD technology, portability, and user-friendly features, it is an excellent choice for anyone in need of a dependable projection solution.
Top Page Image Contents