Kodak KKE PLUS, J-E PLUS Adjusting the Zero Position Switch, Zero Position Switch NUT

Page 30

SERVICE MANUAL

Adjusting the ZERO POSITION SWITCH

SPECIAL APPLICATIONS PLUG

1 4

2

7

5

6

3

8

A100_0022ACA

A100_0022AA

ZERO POSITION

SWITCH

NUT

Important

It is necessary to make a 5/16 in. WRENCH to do this adjustment. See the Tools section.

[1]Energize the projector.

[2]Connect the DIGITAL VOLT METER (DVM) between PINS 1 and 3 (ZERO POSITION SWITCH) of the SPECIAL APPLICATIONS PLUG.

[3]Without a TRAY installed, the DVM should measure •.

[4]Install a TRAY.

[5]To move the TRAY out of the zero position, press the “FORWARD” or “REVERSE” BUTTONS; the DVM should measure 0 W.

[6]If the measurements are not within speciﬁcation, adjust the ZERO POSITION SWITCH ECCENTRIC to speciﬁcation.

A091_0017GCA

A091_0017GA

Adjustment Speciﬁcation

Seat AUTO-FOCUS TARGET SLIDE TL-3002 on the GATE MECHANISM. Use TL-3005 or TL-1165 to bend the AUTO-FOCUS BRACKET ASSEMBLY MIRROR until the image is within the target of the TARGET SLIDE.

30	30APR96 – SM4530-1

Image 30

Contents Kodak Ektagraphic Table of Contents Adjusting the Focus Light Path Auto Focus Models PIN Special Application PlugReplacing the Lower Housing Assembly Installing the Lower Housing AssemblyReplacing the FAN Shaft Assembly Remove the Torx Screw from the Blower Cover AssemblyPainted Projector Installing the FAN Shaft Assembly Replacing the MotorWorm Pulley Screw Mechanism Belt Installing the MotorReplacing the Worm Pulley and Mechanism Belt MotorInstalling the Worm Pulley and Mechanism Belt Replacing the Thermal Fuse AssemblyInstalling the Thermal Fuse Assembly Installing the Lamp Module Receptacle Replacing the Lamp Module ReceptaclePlunger Assembly Replacing the Cycle Solenoid AssemblyInstalling the Cycle Solenoid Assembly Pulley ShaftReplacing the Mechanism Assembly Mechanism AssemblyDark Installing the AUTO-FOCUS Bracket Assembly Installing the Mechanism AssemblyReplacing the AUTO-FOCUS Bracket Assembly Worm Pulley Auto Focusscrew Cyclebracket Solenoid AssemblyReplacing the CAM Stack Assembly and Cycle Lever Assembly Remove the Light Baffle Installing the CAM Stack Assembly and Cycle Lever Assembly Replacing the Lamp Socket Terminal ASSEMBLY, N.P Installing the Lamp Socket Terminal AssemblyReplacing the Lamp Socket Terminal ASSEMBLY, Painted Models Lamp ModuleRetaining Ring Spring Washer Socket PIN Replacing the Lens Mount Assembly Auto Focus Model Installing the Lens Mount Assembly Auto Focus ModelsAUTO-FOCUS Defeat Switch Replacing the Lens Mount Assembly Non Auto Focus Model Installing the Lens Mount Assembly Non Auto Focus ModelReplacing the AUTO-FOCUS Switch Assembly Installing the AUTO-FOCUS Switch AssemblyClamp Lever Screw Replacing the Focus Shaft Assembly Auto Focus ModelsLens Mount Assembly SpringInstalling the Focus Shaft Assembly Replacing the Focus Shaft Assembly Non Auto-Focus ModelsFocus Shaft Spring Assembly Focus Motor Bracket Spacer Installing the Focus Shaft Assembly Adjustment Speciﬁcation Adjusting the Cycle SolenoidMechanism Assembly BAR Cycle Adjusting the Indexer Lever Assembly Adjusting the Slide Lift Lever Manual Slide Lift Lever Guage TL-3001 SelectAdjusting the Slide Lift Lever Power Adjusting the Zero Position Switch Zero Position Switch NUTSpring Hook TL-1165 Auto Focus Bracket Assembly Adjusting the Focus Light Path Auto Focus ModelsAdjustment Tool AUTO-FOCUS Target Slide TL-3002Adjusting the Null Projection TAB Lens AUTO-FOCUSTarget Slide Adjusting the Photocell AUTO-FOCUS Assembly Target Slide PADClamp PAD Adjusting the Clamp PAD Assembly Screw NUT Clamp PAD AssemblyAdjusting the Dark Shutter Dark Shutter Pressure PADWorm Pulley Assembly CAM Stack Assembly Cycle Levers FANA0910023HA A0910022DA AUTO-FOCUS Target Slide Adjustment T-BARAUTO-FOCUS Gauge Super LubeSpecifications PIN Remote Control PIN Special ApplicationsGround Diagnostics Main Motor VoltagesPhotocell Voltages Zero Position SwitchShutter Switch Forward Tray CycleKodak EC-3 Remote Control PIN Remote Cord Plug VoltagesSmall Component Board Assembly 256809 Voltages Power, Illumination, and Cooling Malfunctions Voltage Speciﬁcations General PartsSuper Lube TL-4276 Slide Transport MalfunctionsControl Cycle LeverEccentrics Lever AssemblyPower Slide Lift Lever Direction LeverSwitch Focus Malfunctions Gate Mechanism BoardCheck that the alignment of the Target Eastman Kodak Company

Related manuals

Manual 54 pages 34.68 Kb