FARGO electronic Pro-L manual Monitor, Orientation, Overlay, Pause for Low Ribbon

Page 49

Pro-L Card Printer User’s Manual

Monitor

See Color Matching.

Orientation

Select either Portrait or Landscape. Selecting Portrait causes the card to print in a vertical orientation. Selecting Landscape causes the card to print in a horizontal orientation. An icon illustrating a printed card helps represent the difference between the two.

Overlay

This option is only applicable if you have selected a Ribbon Type with a clear overlay (O) panel. If using such a ribbon, select this option to display options for controlling how the ribbon’s clear overlay panel will be applied.

The Overlay Side options enable the printer to place a clear, protective overlay over the entire printable area of the given card size. All dye-sublimation prints must have either the ribbon’s clear overlay panel or a separate overlaminate applied to them to prevent premature wear or fading. Select the No Overlay option if you do not wish to apply an overlay, or select Overlay Front Side, Overlay Back Side, or Overlay Both Sides to specify the side(s) of the card you would like to overlay.

If laminating with PolyGuard, note that you MUST NOT apply the ribbon overlay to the side of the card that will be laminated, since the overlay will interfere with the adhesion of the overlaminate. Be sure to always double-check these settings before printing. For example, if you selected the Laminate Front Side option from the Lamination controls, DO NOT select the Overlay Front Side option.

This SmartShield Side options are only applicable if you are using the printer’s optional SmartGuard Security Feature and you have enabled its SmartShield option. If so, you must select one of these SmartShield options in order to print your custom SmartShield Security Image. Select SmartShield Front Side, SmartShield Back Side, or SmartShield Both Sides to specify the side(s) of the card on which you would like your custom security image to appear. If the No SmartShield option is selected, your custom security image will not print even if it is encoded on your SmartGuard Access Card. This is a convenient way of turning the SmartShield Security Feature on or off. Note that it is not possible to apply an overlay and a SmartShield image to the same side of a card.

Pause for Low Ribbon

When this option is selected, the printer will beep, pause, and the "Low Ribbon/Clean" message will display on the printer's LCD when approximately 10 prints remain on the print ribbon. At this point, you can either (a) replace the ribbon and press the Pause/Resume button to continue printing with a new ribbon

44

Section 6: Using Your Card Printer

Image 49
Contents Page Printing History Trademark AcknowledgementsFor Users in Canada For Users in the United StatesFor Users in Taiwan Table of Contents Appendix a Magnetic Stripe Encoding Module Thank You IntroductionHOW Your Card Printer Works Dye-SublimationResin Thermal Transfer Special FeaturesSafety Precautions Sicherheitsmaßnahmen Consignes de sécurité Precauciones de seguridad Precauzioni per la Sicurezza Precauções de Segurança Pro-L Card Printer User’s Manual Pro-L Card Printer User’s Manual Pro-L Card Printer User’s Manual Pro-L Card Printer User’s Manual Choosing a Good Location Getting StartedAbout Moisture Condensation Unpacking and Inspection Applying PowerPower Input Port LCD Display Identifying the Printer FeaturesOn LED Light Ready LED Light On/Cancel ButtonPause/Resume Button Security Card SlotPro-L Card Printer User’s Manual About Ribbons Ribbons and CardsStandard Resin Black K Resin-Only RibbonsMetallic Resin Scratch-Off ResinFull-Color Ymcko Dye-Sublimation/Resin RibbonsFull-Color Ymckok Full-Color YmckkLoading Ribbon Into the Printer Take-up Ribbon Drive Hubs Supply Ribbon Sensor Loading Cards Into the Printer About CardsCard Input Tray Card Input Guides Card Hopper Door Self Test Example Actual size Running the Self TestAbout the Laminator Card LaminatingLoading Overlaminate Into the Printer About OverlaminatesSupply Supply Roll Take-up Roll Connecting the Printer to Your Computer Using Your Card PrinterInstalling the Windows Printer Driver Installing Printer Driver Updates Installing the 32-BIT Print Spooler for Windows 95/98 InstallingDownloading Pro-L Card Printer User’s Manual Setting UP the Printer Driver Windows NT Windows 95/98Buffer Single Card AlgebraicCalibrate Card Size Color Matching Dither Mode Disable PrintingImage Placement ControlsLamination Options Panel Only 95% 99%Magnetic Track Options Orientation MonitorOverlay Pause for Low RibbonPrint Back Side Only Picture ControlsPrint Edge-to-Edge Print Both SidesResin Heat Ribbon SensorSplit Ribbon Print SmartShieldUse 32-bit Spooler Write Direct to PortPrinting a Card Maintenance Supplies Required Expanded Printhead Cleaning Standard Printhead CleaningCleaning the PRINTER’S Case Clearing a Card JAM Cleaning the Inside of the PrinterClearing a Ribbon or Overlaminate JAM Cleaning the Card Feed RollersSticky Side Up Cleaning the Drive RollersMaintaining the Cleaning Rollers Pro-L Card Printer User’s Manual Adjusting the Card Input Guides Mechanical AdjustmentsAdjusting the Internal Card Guides Adjusting the Card Separator Flap Card Flap Adjustment Feed Screws Top Card Adjusting the Laminator Pro-L Card Printer User’s Manual Pro-L Card Printer User’s Manual Interpreting LCD Display Messages TroubleshootingTOP Line of LCD Message Cause Solution TOP Line of LCD Message Cause Solution TOP Line of LCD Message Cause Solution TOP Line of LCD Message Cause Solution Only if you are using SmartGuard Security Feature TOP Line of LCD Message Cause Solution If the ribbon seems to be cut Bottom Line of LCD Message Cause Solution Bottom Line of LCD Message Cause Solution Both Lines of LCD Message Cause Solution Both Lines of LCD Message Cause Solution ’m having problems printing from Windows 95/98 General Troubleshooting SuggestionsPrinter beeps just before each ribbon panel is printed Printer doesn’t seem to work at allMy prints have spots small voids in them PolyGuard overlaminate is not centered on my cardPhotos on my ID cards look very pixelated or grainy Printing gets cut off or is not centered on the cardCan’t get the cards in between the Card Input Guides Two or more cards feed at the same timePro-L Card Printer User’s Manual Print Speed Technical SpecificationsCard Capacity Magnetic Track Options Appendix a Magnetic Stripe Encoding ModuleEncoding Mode / Coercivity / Track Selection Character Data Size Encoded Bit DensityCharacter Ascii Offset Character Data Parity LRC Generation ModeSending Track Information ISO Track Locations~20123456789? ~1%JULIE ANDERSON623-85-1253?~30123456789? Introduction Appendix B Interfacing InformationCentronics Type Parallel Interface Table B-1 Parallel Interface Pin Assignments Wire DiagramBar Codes IndexMagnetic Track Options On/cancel button

Pro-L specifications

FARGO Electronic Pro-L is a state-of-the-art card printer designed to meet the rigorous demands of various organizations requiring high-quality plastic card production. Renowned for its reliability and efficiency, the Pro-L series is particularly favored for applications in government, education, healthcare, and corporate environments.

One of the main features of the FARGO Pro-L is its advanced printing technology, which utilizes dye-sublimation and resin thermal transfer methods. This allows users to produce vibrant, high-resolution color images that are both durable and resistant to fading. The printer can deliver edge-to-edge printing, ensuring that every card is visually appealing and professional-looking.

Another notable characteristic of the Pro-L series is its modular design. Users can customize the printer with optional features such as dual-sided printing, which significantly enhances productivity by allowing for the printing of essential information on both sides of the card. Additionally, the printer supports various encoding options like magnetic stripe, smart card, and contactless encoding, making it a versatile solution for diverse applications.

The Pro-L model is equipped with a high-capacity input hopper, which can hold a large number of cards, minimizing the need for frequent refills. Coupled with its impressive printing speed, this feature makes it ideal for high-volume card issuance. The device can print up to 225 full-color cards per hour, streamlining the production process and ensuring timely delivery.

Security is another priority in the design of the FARGO Pro-L. The printer includes features such as user authentication and built-in encryption for data protection. These measures are essential for organizations requiring secure handling of sensitive information, such as IDs, access cards, and payment cards.

Furthermore, the FARGO Pro-L is compatible with various card design software, allowing users to create customized card designs easily. The user-friendly interface simplifies operation, making it accessible for personnel with varying levels of technical expertise.

In conclusion, the FARGO Electronic Pro-L is a comprehensive solution for organizations seeking an efficient, secure, and flexible card printing system. With its advanced features, high-quality output, and customizable options, it stands out as a top choice for professionals looking to enhance their card production capabilities.