FARGO electronic Pro-L manual Appendix a Magnetic Stripe Encoding Module, Magnetic Track Options

Page 88

Appendix A:

Magnetic Stripe

Encoding Module

A

A. MAGNETIC TRACK OPTIONS

The card printer can be purchased with one of two types of factory-installed Magnetic Stripe Encoding Modules. The first, most common type is an ISO Standard encoding module with a dual-coercivity (high or low) encoding head. The second is a JIS II Standard encoding module commonly used in Japan.

By default, the printer driver is set to encode according to ISO standards onto high- coercivity magnetic stripes. To change the encoding mode, coercivity setting, or to modify the ISO standards for tracks 1, 2, and 3, simply select the Magnetic Track Options tab (or Magnetics button) from within the printer driver setup window. The Magnetic Track Options will display.

Appendix A: Magnetic Stripe Encoding Module

83

Page 87 Page 89
Image 88
Page 87 Page 89
Contents Page Trademark Acknowledgements Printing HistoryFor Users in Canada For Users in the United StatesFor Users in Taiwan Table of Contents Appendix a Magnetic Stripe Encoding Module Introduction Thank YouHOW Your Card Printer Works Dye-SublimationSpecial Features Resin Thermal TransferSafety Precautions Sicherheitsmaßnahmen Consignes de sécurité Precauciones de seguridad Precauzioni per la Sicurezza Precauções de Segurança Pro-L Card Printer User’s Manual Pro-L Card Printer User’s Manual Pro-L Card Printer User’s Manual Pro-L Card Printer User’s Manual Choosing a Good Location Getting StartedAbout Moisture Condensation Applying Power Unpacking and InspectionPower Input Port LCD Display Identifying the Printer FeaturesOn LED Light On/Cancel Button Ready LED LightPause/Resume Button Security Card SlotPro-L Card Printer User’s Manual Ribbons and Cards About RibbonsResin-Only Ribbons Standard Resin Black KMetallic Resin Scratch-Off ResinDye-Sublimation/Resin Ribbons Full-Color YmckoFull-Color Ymckok Full-Color YmckkLoading Ribbon Into the Printer Take-up Ribbon Drive Hubs Supply Ribbon Sensor About Cards Loading Cards Into the PrinterCard Input Tray Card Input Guides Card Hopper Door Running the Self Test Self Test Example Actual sizeCard Laminating About the LaminatorAbout Overlaminates Loading Overlaminate Into the PrinterSupply Supply Roll Take-up Roll Using Your Card Printer Connecting the Printer to Your ComputerInstalling the Windows Printer Driver Installing Printer Driver Updates Installing the 32-BIT Print Spooler for Windows 95/98 InstallingDownloading Pro-L Card Printer User’s Manual Setting UP the Printer Driver Windows 95/98 Windows NTBuffer Single Card AlgebraicCalibrate Card Size Color Matching Disable Printing Dither ModeImage Placement ControlsPanel Only 95% 99% Lamination OptionsMagnetic Track Options Monitor OrientationOverlay Pause for Low RibbonPicture Controls Print Back Side OnlyPrint Both Sides Print Edge-to-EdgeResin Heat Ribbon SensorSmartShield Split Ribbon PrintUse 32-bit Spooler Write Direct to PortPrinting a Card Maintenance Supplies Required Expanded Printhead Cleaning Standard Printhead CleaningCleaning the PRINTER’S Case Cleaning the Inside of the Printer Clearing a Card JAMCleaning the Card Feed Rollers Clearing a Ribbon or Overlaminate JAMCleaning the Drive Rollers Sticky Side UpMaintaining the Cleaning Rollers Pro-L Card Printer User’s Manual Mechanical Adjustments Adjusting the Card Input GuidesAdjusting the Internal Card Guides Adjusting the Card Separator Flap Card Flap Adjustment Feed Screws Top Card Adjusting the Laminator Pro-L Card Printer User’s Manual Pro-L Card Printer User’s Manual Troubleshooting Interpreting LCD Display MessagesTOP Line of LCD Message Cause Solution TOP Line of LCD Message Cause Solution TOP Line of LCD Message Cause Solution TOP Line of LCD Message Cause Solution Only if you are using SmartGuard Security Feature TOP Line of LCD Message Cause Solution If the ribbon seems to be cut Bottom Line of LCD Message Cause Solution Bottom Line of LCD Message Cause Solution Both Lines of LCD Message Cause Solution Both Lines of LCD Message Cause Solution General Troubleshooting Suggestions ’m having problems printing from Windows 95/98Printer beeps just before each ribbon panel is printed Printer doesn’t seem to work at allPolyGuard overlaminate is not centered on my card My prints have spots small voids in themPhotos on my ID cards look very pixelated or grainy Printing gets cut off or is not centered on the cardTwo or more cards feed at the same time Can’t get the cards in between the Card Input GuidesPro-L Card Printer User’s Manual Technical Specifications Print SpeedCard Capacity Appendix a Magnetic Stripe Encoding Module Magnetic Track OptionsEncoding Mode / Coercivity / Track Selection Character Data Size Encoded Bit DensityCharacter Ascii Offset LRC Generation Mode Character Data ParityISO Track Locations Sending Track Information~20123456789? ~1%JULIE ANDERSON623-85-1253?~30123456789? Introduction Appendix B Interfacing InformationCentronics Type Parallel Interface Wire Diagram Table B-1 Parallel Interface Pin AssignmentsIndex Bar CodesMagnetic Track Options On/cancel button

Pro-L specifications

FARGO Electronic Pro-L is a state-of-the-art card printer designed to meet the rigorous demands of various organizations requiring high-quality plastic card production. Renowned for its reliability and efficiency, the Pro-L series is particularly favored for applications in government, education, healthcare, and corporate environments.

One of the main features of the FARGO Pro-L is its advanced printing technology, which utilizes dye-sublimation and resin thermal transfer methods. This allows users to produce vibrant, high-resolution color images that are both durable and resistant to fading. The printer can deliver edge-to-edge printing, ensuring that every card is visually appealing and professional-looking.

Another notable characteristic of the Pro-L series is its modular design. Users can customize the printer with optional features such as dual-sided printing, which significantly enhances productivity by allowing for the printing of essential information on both sides of the card. Additionally, the printer supports various encoding options like magnetic stripe, smart card, and contactless encoding, making it a versatile solution for diverse applications.

The Pro-L model is equipped with a high-capacity input hopper, which can hold a large number of cards, minimizing the need for frequent refills. Coupled with its impressive printing speed, this feature makes it ideal for high-volume card issuance. The device can print up to 225 full-color cards per hour, streamlining the production process and ensuring timely delivery.

Security is another priority in the design of the FARGO Pro-L. The printer includes features such as user authentication and built-in encryption for data protection. These measures are essential for organizations requiring secure handling of sensitive information, such as IDs, access cards, and payment cards.

Furthermore, the FARGO Pro-L is compatible with various card design software, allowing users to create customized card designs easily. The user-friendly interface simplifies operation, making it accessible for personnel with varying levels of technical expertise.

In conclusion, the FARGO Electronic Pro-L is a comprehensive solution for organizations seeking an efficient, secure, and flexible card printing system. With its advanced features, high-quality output, and customizable options, it stands out as a top choice for professionals looking to enhance their card production capabilities.
Top Page Image Contents