FARGO electronic Pro-L manual Standard Printhead Cleaning, Expanded Printhead Cleaning

Page 56

Pro-L Card Printer User’s Manual

B. STANDARD PRINTHEAD CLEANING

This procedure should be performed if you notice a streak on the card where color was not transferred. This procedure should also be performed during every ribbon change or after every 250 prints in order to maintain consistent print quality. The printhead is located near the center of the opened Top Cover assembly.

1.Open the printer’s top-right cover by pressing its Cover Release Button.

2.If you observe dust and/or other particles laying on the top surface of the ribbon, manually roll it up into the take-up roll. Occasionally, dust may settle on the top surface of the ribbon and cause print quality problems.

3.Use a Printhead Cleaning Pen from the Printer Cleaning Kit or a soft, lint-free cloth slightly moistened with isopropyl alcohol to wipe dust and other accumulated particles off the surface of the printhead. If using a cloth, be extremely careful not to use too much alcohol. It must not be allowed to drip into the printer!

4.Once the printhead is completely dry, shut the cover. If a streak persists, perform the steps in Part C.

C.EXPANDED PRINTHEAD CLEANING

Perform if you have a streak on the printed output that can’t be solved by the Standard Printhead Cleaning procedure. To maintain your printer’s high quality of printing, this procedure should also be performed approximately every 2,500 prints as part of the printer’s general maintenance program.

1.Open the printer’s top-right cover by pressing its Cover Release Button.

2.Use a soft, lint-free cloth slightly moistened with acetone to wipe off the surface of the printhead. Be extremely careful not to use too much acetone. It must not be allowed to drip into the printer!

CAUTION! ACETONE IS A VERY POWERFUL SOLVENT. DO NOT APPLY ACETONE TO ANY OTHER AREA OF THE PRINTER, SINCE IT WILL DESTROY THE FINISH OF PAINT, RUBBER, AND PLASTIC.

3.Allow the printhead to thoroughly dry before closing the cover.

4.Shut the cover. If a streak persists, contact your dealer for further assistance.

D. CLEANING THE PRINTER’S CASE

The printer has a durable casing that should retain its luster and appearance for many years. Clean it only with a soft cloth slightly dampened with water or a mild soap. Do not use excess water or cleaning solvents of any kind. Never spray the cabinet with a cleaner. Rather, spray the cloth first, then wipe down the printer.

Section 7: Maintenance

51

Image 56
Contents Page Trademark Acknowledgements Printing HistoryFor Users in Taiwan For Users in the United StatesFor Users in Canada Table of Contents Appendix a Magnetic Stripe Encoding Module Introduction Thank YouHOW Your Card Printer Works Dye-SublimationSpecial Features Resin Thermal TransferSafety Precautions Sicherheitsmaßnahmen Consignes de sécurité Precauciones de seguridad Precauzioni per la Sicurezza Precauções de Segurança Pro-L Card Printer User’s Manual Pro-L Card Printer User’s Manual Pro-L Card Printer User’s Manual Pro-L Card Printer User’s Manual About Moisture Condensation Getting StartedChoosing a Good Location Applying Power Unpacking and InspectionPower Input Port On LED Light Identifying the Printer FeaturesLCD Display On/Cancel Button Ready LED LightPause/Resume Button Security Card SlotPro-L Card Printer User’s Manual Ribbons and Cards About RibbonsResin-Only Ribbons Standard Resin Black KMetallic Resin Scratch-Off ResinDye-Sublimation/Resin Ribbons Full-Color YmckoFull-Color Ymckok Full-Color YmckkLoading Ribbon Into the Printer Take-up Ribbon Drive Hubs Supply Ribbon Sensor About Cards Loading Cards Into the PrinterCard Input Tray Card Input Guides Card Hopper Door Running the Self Test Self Test Example Actual sizeCard Laminating About the LaminatorAbout Overlaminates Loading Overlaminate Into the PrinterSupply Supply Roll Take-up Roll Using Your Card Printer Connecting the Printer to Your ComputerInstalling the Windows Printer Driver Installing Printer Driver Updates Downloading InstallingInstalling the 32-BIT Print Spooler for Windows 95/98 Pro-L Card Printer User’s Manual Setting UP the Printer Driver Windows 95/98 Windows NTCalibrate AlgebraicBuffer Single Card Card Size Color Matching Disable Printing Dither ModeImage Placement ControlsPanel Only 95% 99% Lamination OptionsMagnetic Track Options Monitor OrientationOverlay Pause for Low RibbonPicture Controls Print Back Side OnlyPrint Both Sides Print Edge-to-EdgeResin Heat Ribbon SensorSmartShield Split Ribbon PrintUse 32-bit Spooler Write Direct to PortPrinting a Card Maintenance Supplies Required Cleaning the PRINTER’S Case Standard Printhead CleaningExpanded Printhead Cleaning Cleaning the Inside of the Printer Clearing a Card JAMCleaning the Card Feed Rollers Clearing a Ribbon or Overlaminate JAMCleaning the Drive Rollers Sticky Side UpMaintaining the Cleaning Rollers Pro-L Card Printer User’s Manual Mechanical Adjustments Adjusting the Card Input GuidesAdjusting the Internal Card Guides Adjusting the Card Separator Flap Card Flap Adjustment Feed Screws Top Card Adjusting the Laminator Pro-L Card Printer User’s Manual Pro-L Card Printer User’s Manual Troubleshooting Interpreting LCD Display MessagesTOP Line of LCD Message Cause Solution TOP Line of LCD Message Cause Solution TOP Line of LCD Message Cause Solution TOP Line of LCD Message Cause Solution Only if you are using SmartGuard Security Feature TOP Line of LCD Message Cause Solution If the ribbon seems to be cut Bottom Line of LCD Message Cause Solution Bottom Line of LCD Message Cause Solution Both Lines of LCD Message Cause Solution Both Lines of LCD Message Cause Solution General Troubleshooting Suggestions ’m having problems printing from Windows 95/98Printer beeps just before each ribbon panel is printed Printer doesn’t seem to work at allPolyGuard overlaminate is not centered on my card My prints have spots small voids in themPhotos on my ID cards look very pixelated or grainy Printing gets cut off or is not centered on the cardTwo or more cards feed at the same time Can’t get the cards in between the Card Input GuidesPro-L Card Printer User’s Manual Technical Specifications Print SpeedCard Capacity Appendix a Magnetic Stripe Encoding Module Magnetic Track OptionsEncoding Mode / Coercivity / Track Selection Character Ascii Offset Encoded Bit DensityCharacter Data Size LRC Generation Mode Character Data ParityISO Track Locations Sending Track Information~30123456789? ~1%JULIE ANDERSON623-85-1253?~20123456789? Centronics Type Parallel Interface Appendix B Interfacing InformationIntroduction Wire Diagram Table B-1 Parallel Interface Pin AssignmentsIndex Bar CodesMagnetic Track Options On/cancel button

Pro-L specifications

FARGO Electronic Pro-L is a state-of-the-art card printer designed to meet the rigorous demands of various organizations requiring high-quality plastic card production. Renowned for its reliability and efficiency, the Pro-L series is particularly favored for applications in government, education, healthcare, and corporate environments.

One of the main features of the FARGO Pro-L is its advanced printing technology, which utilizes dye-sublimation and resin thermal transfer methods. This allows users to produce vibrant, high-resolution color images that are both durable and resistant to fading. The printer can deliver edge-to-edge printing, ensuring that every card is visually appealing and professional-looking.

Another notable characteristic of the Pro-L series is its modular design. Users can customize the printer with optional features such as dual-sided printing, which significantly enhances productivity by allowing for the printing of essential information on both sides of the card. Additionally, the printer supports various encoding options like magnetic stripe, smart card, and contactless encoding, making it a versatile solution for diverse applications.

The Pro-L model is equipped with a high-capacity input hopper, which can hold a large number of cards, minimizing the need for frequent refills. Coupled with its impressive printing speed, this feature makes it ideal for high-volume card issuance. The device can print up to 225 full-color cards per hour, streamlining the production process and ensuring timely delivery.

Security is another priority in the design of the FARGO Pro-L. The printer includes features such as user authentication and built-in encryption for data protection. These measures are essential for organizations requiring secure handling of sensitive information, such as IDs, access cards, and payment cards.

Furthermore, the FARGO Pro-L is compatible with various card design software, allowing users to create customized card designs easily. The user-friendly interface simplifies operation, making it accessible for personnel with varying levels of technical expertise.

In conclusion, the FARGO Electronic Pro-L is a comprehensive solution for organizations seeking an efficient, secure, and flexible card printing system. With its advanced features, high-quality output, and customizable options, it stands out as a top choice for professionals looking to enhance their card production capabilities.