FARGO electronic Pro-L manual Cleaning the Inside of the Printer, Clearing a Card JAM

Page 57

Pro-L Card Printer User’s Manual

E. CLEANING THE INSIDE OF THE PRINTER

As you use your printer, dust and other foreign particles may accumulate inside the printer’s case. These particles are attracted to the underside of the ribbon by static produced during printing and can cause voids on the printed image.

Periodically, use the following procedure to remove dust and other foreign particles:

1.Open the printer’s Top Covers.

2.Remove the ribbon and overlaminate from the printer.

3.Use a Cleaning Pad from the Printer Cleaning Kit or a soft, lint-free cloth slightly moistened with isopropyl alcohol to wipe out all visible areas inside the printer. Remove any debris that may be inside. Be extremely careful not to let any alcohol drip inside the printer!

4.Once the cleaned areas are completely dry and free of foreign debris, re-install the ribbon and overlaminate, and close the covers.

F.CLEARING A CARD JAM

If a card becomes jammed inside the printer, the LCD Display will indicate approximately where it is jammed. At this point you can either try to correct the problem and continue printing with the same card, or remove the card completely and continue printing with a new card. Refer to the following steps for instructions on doing either:

1.Leave the power ON, and open of the printer’s Top Covers.

2.Remove the ribbon and overlaminate as needed.

3.If you would like to try to correct the problem and continue printing with the same card, do so by pressing the On/Cancel button to advance the card or the Pause/Resume button to reverse the card. Use these buttons to help free the card from its jam. Try not to move the card too far from where it was just before the jam occurred. Once the jam is cleared, replace media, close the Top Cover(s), and press the Pause/Resume button to resume printing.

4.If you would like to remove the jammed card completely, do so by using the On/Cancel and Pause/Resume buttons to manually eject the card. Then, replace media, close the Top Covers, and press the On/Cancel button. At this point, the LCD Display will prompt you to either press the Pause/Resume button or the On/Cancel button. Pressing the Pause/Resume button will cause the printer to feed in a new card and reprint the job which originally jammed along with all subsequent jobs still being sent. Pressing the On/Cancel button will reboot the printer and cancel all jobs within the printer’s memory. In this case, you must also cancel and resend the print jobs from your computer.

52

Section 7: Maintenance

Page 56 Page 58
Image 57
Page 56 Page 58
Contents Page Printing History Trademark AcknowledgementsFor Users in the United States For Users in CanadaFor Users in Taiwan Table of Contents Appendix a Magnetic Stripe Encoding Module Thank You IntroductionHOW Your Card Printer Works Dye-SublimationResin Thermal Transfer Special FeaturesSafety Precautions Sicherheitsmaßnahmen Consignes de sécurité Precauciones de seguridad Precauzioni per la Sicurezza Precauções de Segurança Pro-L Card Printer User’s Manual Pro-L Card Printer User’s Manual Pro-L Card Printer User’s Manual Pro-L Card Printer User’s Manual Getting Started Choosing a Good LocationAbout Moisture Condensation Unpacking and Inspection Applying PowerPower Input Port Identifying the Printer Features LCD DisplayOn LED Light Ready LED Light On/Cancel ButtonPause/Resume Button Security Card SlotPro-L Card Printer User’s Manual About Ribbons Ribbons and CardsStandard Resin Black K Resin-Only RibbonsMetallic Resin Scratch-Off ResinFull-Color Ymcko Dye-Sublimation/Resin RibbonsFull-Color Ymckok Full-Color YmckkLoading Ribbon Into the Printer Take-up Ribbon Drive Hubs Supply Ribbon Sensor Loading Cards Into the Printer About CardsCard Input Tray Card Input Guides Card Hopper Door Self Test Example Actual size Running the Self TestAbout the Laminator Card LaminatingLoading Overlaminate Into the Printer About OverlaminatesSupply Supply Roll Take-up Roll Connecting the Printer to Your Computer Using Your Card PrinterInstalling the Windows Printer Driver Installing Printer Driver Updates Installing Installing the 32-BIT Print Spooler for Windows 95/98Downloading Pro-L Card Printer User’s Manual Setting UP the Printer Driver Windows NT Windows 95/98Algebraic Buffer Single CardCalibrate Card Size Color Matching Dither Mode Disable PrintingImage Placement ControlsLamination Options Panel Only 95% 99%Magnetic Track Options Orientation MonitorOverlay Pause for Low RibbonPrint Back Side Only Picture ControlsPrint Edge-to-Edge Print Both SidesResin Heat Ribbon SensorSplit Ribbon Print SmartShieldUse 32-bit Spooler Write Direct to PortPrinting a Card Maintenance Supplies Required Standard Printhead Cleaning Expanded Printhead CleaningCleaning the PRINTER’S Case Clearing a Card JAM Cleaning the Inside of the PrinterClearing a Ribbon or Overlaminate JAM Cleaning the Card Feed RollersSticky Side Up Cleaning the Drive RollersMaintaining the Cleaning Rollers Pro-L Card Printer User’s Manual Adjusting the Card Input Guides Mechanical AdjustmentsAdjusting the Internal Card Guides Adjusting the Card Separator Flap Card Flap Adjustment Feed Screws Top Card Adjusting the Laminator Pro-L Card Printer User’s Manual Pro-L Card Printer User’s Manual Interpreting LCD Display Messages TroubleshootingTOP Line of LCD Message Cause Solution TOP Line of LCD Message Cause Solution TOP Line of LCD Message Cause Solution TOP Line of LCD Message Cause Solution Only if you are using SmartGuard Security Feature TOP Line of LCD Message Cause Solution If the ribbon seems to be cut Bottom Line of LCD Message Cause Solution Bottom Line of LCD Message Cause Solution Both Lines of LCD Message Cause Solution Both Lines of LCD Message Cause Solution ’m having problems printing from Windows 95/98 General Troubleshooting SuggestionsPrinter beeps just before each ribbon panel is printed Printer doesn’t seem to work at allMy prints have spots small voids in them PolyGuard overlaminate is not centered on my cardPhotos on my ID cards look very pixelated or grainy Printing gets cut off or is not centered on the cardCan’t get the cards in between the Card Input Guides Two or more cards feed at the same timePro-L Card Printer User’s Manual Print Speed Technical SpecificationsCard Capacity Magnetic Track Options Appendix a Magnetic Stripe Encoding ModuleEncoding Mode / Coercivity / Track Selection Encoded Bit Density Character Data SizeCharacter Ascii Offset Character Data Parity LRC Generation ModeSending Track Information ISO Track Locations~1%JULIE ANDERSON623-85-1253? ~20123456789?~30123456789? Appendix B Interfacing Information IntroductionCentronics Type Parallel Interface Table B-1 Parallel Interface Pin Assignments Wire DiagramBar Codes IndexMagnetic Track Options On/cancel button

Pro-L specifications

FARGO Electronic Pro-L is a state-of-the-art card printer designed to meet the rigorous demands of various organizations requiring high-quality plastic card production. Renowned for its reliability and efficiency, the Pro-L series is particularly favored for applications in government, education, healthcare, and corporate environments.

One of the main features of the FARGO Pro-L is its advanced printing technology, which utilizes dye-sublimation and resin thermal transfer methods. This allows users to produce vibrant, high-resolution color images that are both durable and resistant to fading. The printer can deliver edge-to-edge printing, ensuring that every card is visually appealing and professional-looking.

Another notable characteristic of the Pro-L series is its modular design. Users can customize the printer with optional features such as dual-sided printing, which significantly enhances productivity by allowing for the printing of essential information on both sides of the card. Additionally, the printer supports various encoding options like magnetic stripe, smart card, and contactless encoding, making it a versatile solution for diverse applications.

The Pro-L model is equipped with a high-capacity input hopper, which can hold a large number of cards, minimizing the need for frequent refills. Coupled with its impressive printing speed, this feature makes it ideal for high-volume card issuance. The device can print up to 225 full-color cards per hour, streamlining the production process and ensuring timely delivery.

Security is another priority in the design of the FARGO Pro-L. The printer includes features such as user authentication and built-in encryption for data protection. These measures are essential for organizations requiring secure handling of sensitive information, such as IDs, access cards, and payment cards.

Furthermore, the FARGO Pro-L is compatible with various card design software, allowing users to create customized card designs easily. The user-friendly interface simplifies operation, making it accessible for personnel with varying levels of technical expertise.

In conclusion, the FARGO Electronic Pro-L is a comprehensive solution for organizations seeking an efficient, secure, and flexible card printing system. With its advanced features, high-quality output, and customizable options, it stands out as a top choice for professionals looking to enhance their card production capabilities.
Top Page Image Contents