FARGO electronic Pro-L manual Safety Precautions

Page 8

Safety Precautions

2

Before operating the unit, please read the following safety precautions carefully.

WARNINGS

CAUTION!

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE FRONT, TOP OR BACK PANELS. NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

νOperate the unit only on 100-240 VAC, 50/60 Hz. If you have any doubt as to whether you have a unit with the correct voltage rating for your country’s power supply, DO NOT attempt to use the unit. Contact your dealer or the factory.

νStop operation immediately if any liquid or solid object should fall into the cabinet. Unplug the unit and have it checked by qualified service personnel.

νUnplug the unit’s power transformer from the wall outlet if you do not use the unit for a long time. Disconnect the cord by grasping the plug. Never pull the cord itself.

νThe unit is not disconnected from the main power source as long as the power transformer is plugged into the wall outlet, even if the unit itself has been turned off.

νDo not disassemble the cabinet. Refer servicing only to qualified personnel.

νService personnel: parts of this device may be damaged if exposed to static electrical discharges generated by various means, such as walking on a carpeted floor. To avoid potential damage, always wear an appropriate personal grounding device, such as a wrist strap (with integral resistor) connected to an ESD ground. Or, at a minimum, make positive contact with the bare metal chassis of the printer with your hand prior to touching any internal electrical components.

Section 2: Safety Precautions

3

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Page Trademark Acknowledgements Printing HistoryFor Users in Taiwan For Users in the United StatesFor Users in Canada Table of Contents Appendix a Magnetic Stripe Encoding Module Introduction Thank YouHOW Your Card Printer Works Dye-SublimationSpecial Features Resin Thermal TransferSafety Precautions Sicherheitsmaßnahmen Consignes de sécurité Precauciones de seguridad Precauzioni per la Sicurezza Precauções de Segurança Pro-L Card Printer User’s Manual Pro-L Card Printer User’s Manual Pro-L Card Printer User’s Manual Pro-L Card Printer User’s Manual About Moisture Condensation Getting StartedChoosing a Good Location Applying Power Unpacking and InspectionPower Input Port On LED Light Identifying the Printer FeaturesLCD Display On/Cancel Button Ready LED LightPause/Resume Button Security Card SlotPro-L Card Printer User’s Manual Ribbons and Cards About RibbonsResin-Only Ribbons Standard Resin Black KMetallic Resin Scratch-Off ResinDye-Sublimation/Resin Ribbons Full-Color YmckoFull-Color Ymckok Full-Color YmckkLoading Ribbon Into the Printer Take-up Ribbon Drive Hubs Supply Ribbon Sensor About Cards Loading Cards Into the PrinterCard Input Tray Card Input Guides Card Hopper Door Running the Self Test Self Test Example Actual sizeCard Laminating About the LaminatorAbout Overlaminates Loading Overlaminate Into the PrinterSupply Supply Roll Take-up Roll Using Your Card Printer Connecting the Printer to Your ComputerInstalling the Windows Printer Driver Installing Printer Driver Updates Downloading InstallingInstalling the 32-BIT Print Spooler for Windows 95/98 Pro-L Card Printer User’s Manual Setting UP the Printer Driver Windows 95/98 Windows NTCalibrate AlgebraicBuffer Single Card Card Size Color Matching Disable Printing Dither ModeImage Placement ControlsPanel Only 95% 99% Lamination OptionsMagnetic Track Options Monitor OrientationOverlay Pause for Low RibbonPicture Controls Print Back Side OnlyPrint Both Sides Print Edge-to-EdgeResin Heat Ribbon SensorSmartShield Split Ribbon PrintUse 32-bit Spooler Write Direct to PortPrinting a Card Maintenance Supplies Required Cleaning the PRINTER’S Case Standard Printhead CleaningExpanded Printhead Cleaning Cleaning the Inside of the Printer Clearing a Card JAMCleaning the Card Feed Rollers Clearing a Ribbon or Overlaminate JAMCleaning the Drive Rollers Sticky Side UpMaintaining the Cleaning Rollers Pro-L Card Printer User’s Manual Mechanical Adjustments Adjusting the Card Input GuidesAdjusting the Internal Card Guides Adjusting the Card Separator Flap Card Flap Adjustment Feed Screws Top Card Adjusting the Laminator Pro-L Card Printer User’s Manual Pro-L Card Printer User’s Manual Troubleshooting Interpreting LCD Display MessagesTOP Line of LCD Message Cause Solution TOP Line of LCD Message Cause Solution TOP Line of LCD Message Cause Solution TOP Line of LCD Message Cause Solution Only if you are using SmartGuard Security Feature TOP Line of LCD Message Cause Solution If the ribbon seems to be cut Bottom Line of LCD Message Cause Solution Bottom Line of LCD Message Cause Solution Both Lines of LCD Message Cause Solution Both Lines of LCD Message Cause Solution General Troubleshooting Suggestions ’m having problems printing from Windows 95/98Printer beeps just before each ribbon panel is printed Printer doesn’t seem to work at allPolyGuard overlaminate is not centered on my card My prints have spots small voids in themPhotos on my ID cards look very pixelated or grainy Printing gets cut off or is not centered on the cardTwo or more cards feed at the same time Can’t get the cards in between the Card Input GuidesPro-L Card Printer User’s Manual Technical Specifications Print SpeedCard Capacity Appendix a Magnetic Stripe Encoding Module Magnetic Track OptionsEncoding Mode / Coercivity / Track Selection Character Ascii Offset Encoded Bit DensityCharacter Data Size LRC Generation Mode Character Data ParityISO Track Locations Sending Track Information~30123456789? ~1%JULIE ANDERSON623-85-1253?~20123456789? Centronics Type Parallel Interface Appendix B Interfacing InformationIntroduction Wire Diagram Table B-1 Parallel Interface Pin AssignmentsIndex Bar CodesMagnetic Track Options On/cancel button

Pro-L specifications

FARGO Electronic Pro-L is a state-of-the-art card printer designed to meet the rigorous demands of various organizations requiring high-quality plastic card production. Renowned for its reliability and efficiency, the Pro-L series is particularly favored for applications in government, education, healthcare, and corporate environments.

One of the main features of the FARGO Pro-L is its advanced printing technology, which utilizes dye-sublimation and resin thermal transfer methods. This allows users to produce vibrant, high-resolution color images that are both durable and resistant to fading. The printer can deliver edge-to-edge printing, ensuring that every card is visually appealing and professional-looking.

Another notable characteristic of the Pro-L series is its modular design. Users can customize the printer with optional features such as dual-sided printing, which significantly enhances productivity by allowing for the printing of essential information on both sides of the card. Additionally, the printer supports various encoding options like magnetic stripe, smart card, and contactless encoding, making it a versatile solution for diverse applications.

The Pro-L model is equipped with a high-capacity input hopper, which can hold a large number of cards, minimizing the need for frequent refills. Coupled with its impressive printing speed, this feature makes it ideal for high-volume card issuance. The device can print up to 225 full-color cards per hour, streamlining the production process and ensuring timely delivery.

Security is another priority in the design of the FARGO Pro-L. The printer includes features such as user authentication and built-in encryption for data protection. These measures are essential for organizations requiring secure handling of sensitive information, such as IDs, access cards, and payment cards.

Furthermore, the FARGO Pro-L is compatible with various card design software, allowing users to create customized card designs easily. The user-friendly interface simplifies operation, making it accessible for personnel with varying levels of technical expertise.

In conclusion, the FARGO Electronic Pro-L is a comprehensive solution for organizations seeking an efficient, secure, and flexible card printing system. With its advanced features, high-quality output, and customizable options, it stands out as a top choice for professionals looking to enhance their card production capabilities.
Top Page Image Contents