Kyocera FS-1010 F010 Controller checksum error, F020 Controller RAM read/write error

Page 130

(7) 7990 - Waste toner full [Total page count more than 100,000 pages of printing]

Call service 7990:nnnnnn

Shake the process unit horizontally.

Turn power switch off, then on.

"7990" error

shown?

No

End.

Printer indicators

	Replace the process
	unit.
	Turn power switch off,
	then on.
	"7990" error	No
Yes	shown?
	Yes	End.
	Yes

Replace the waste toner sensor or engine board (KP-882). See page 5-11.

(8) F010 - Controller checksum error

Turn power switch off, then on. If not solved, replace main board (See page 5-12).

Printer indicators

Remote Operation Panel

Call service

F010:nnnnnn

(9) F020 - Controller RAM read/write error

Remove the expansion memory (DIMM). Turn power switch off, then on. If not solved, replace main board. If solved, replace the expanding memory (See pages 2-8 and 5-12).

Printer indicators

Remote Operation Panel

Call service

F020:nnnnnn

FS-1010

6-18

Image 130

Contents Service Manual Revision history Safety precautions Safety warnings and precautions Installation Precautions Precautions for Maintenance Miscellaneous Appendix a O d u c t I n f o r m a t i o n ChapterContents Printer specifications Specifications EngineWeight and dimensions ControllerPower requirements Environmental requirementsNames of parts Name of partsLaser notice Safety informationSafety information Laser safety Laser caution label on the scanner unit1 Caution labels Ozone concentration Important note on the interface connectorsCdrh regulations U.S.A Optional equipmentEnvironmental requirements Environmental conditionsClearance 2 ClearancesPlaces to avoid Removing the printer Toner container About the toner containerToner container handling Toner container storage Installation / O p e r a t i o n Unpacking Unpacking Unpacking and inspectionInstalling the printer Installing the toner container2 Shaking the toner container 4 Installing the toner container 5 Locking the toner container Expanding memory Dimm specificationsMinimum memory requirements 6 Handling Dimm Installing the Dimm 7 Removing side cover8 Inserting the Dimm Testing the expansion memory Installing the memory card CompactFlash 9 Removing the option interface slot cover10 installing the memory card Installing the network interface card 11 installing the memory cardOperator panel Using the operator panel1 Operator panel function Remote operation panel 2 Remote operation panel 2 Remote operation panel functionMaintenance/Adjustments Downloading the firmware from the parallel interface Life expectancy of modules Maintenance/Adjustments1 Life expectancy of modules When to replace the toner container 2 Toner containerToner container replacement 1 Releasing Lock levers #1 and #2Toner saver mode EcoPrint 3 Disposal of the old toner containerCleaning the printer 4 Removing the process unitCleaning the registration roller 6 Cleaning the main charger wireUpdating the firmware Firmware program data formatDownloading the firmware from the parallel interface Downloading the firmware from the memory card Downloading errors Download errorsE r a t i o n O v e r v i e w Chapter Contents Electrophotographic system Electrophotographic cycleProcess unit mechanism 2 Process unit mechanismMain charging Photo conductive drum 3 Photo conductive drumCharging the drum 4 Charging the drumExposure 5 ExposureLaser scanner unit 6 Laser scanner unitDrum surface potential 7 Drum surface potentialDevelopment 8 DevelopmentTransfer 9 TransferFusing 10 FusingFuser unit mechanism 11 Fuser unit mechanismCleaning 12 Drum cleaning and erasing static chargePaper feeding system 1 Paper feeding pathPaper feed control 2 Paper feed controlPaper feeding mechanism 3 Paper feeding mechanismElectrical control system Electrical parts layout2 Main board circuit block diagram Operation of circuit Boards Main board3 Engine board circuit block diagram Engine boardEraser lamp control circuit 4 Eraser lamp control circuitHeater lamp control circuit 5 heater lamp control circuitFS-1010 6 heater lamp turn-on variations Polygon motor control circuit 7 Polygon motor control circuitPower supply board 8 Power supply board circuit block diagram9 Bias board circuit block diagram Bias board10 High voltage board circuit block diagram High voltage boardInterlock switch 11 Interlock switchS a s s e m b l y Removing the power supply board and high voltage board General instructions Before starting disassemblyScrew/hardware Disassembly Removing the process unit2 Removing the top cover/face-down output tray Removing the right cover 3 Removing the right cover Removing the left coverRemoving the feed roller 5 Removing the feed rollerRemoving the MP tray feed roller 6 Removing the MP feed clutch7 Removing the MP feed unit Removing the transfer roller 9 Removing the transfer roller10 Removing the engine board Removing the main board 11 Removing the controller box with main board12 Removing the main board Removing the power supply board and high voltage board 13 Removing the power supply board and high voltage boardRemoving the bias board 14 Removing the bias boardRemoving the main motor and drive unit 15 Removing the main motorRemoving the cord cover 17 Removing the clutches 18 Removing the drive unit Removing and splitting the fuser unit 19 Removing the fuser unit20 Splitting the fuser unit Removing the separators 21 Removing the separatorsRemoving the heater lamp 22 Removing the heater lampRemoving the heat roller 23 Removing the heat R bush and heat L bush24 Removing the heat roller Removing the thermistor 25 Removing the thermistorRemoving the thermal cutout 26 Removing the thermal cutoutRemoving the press roller 27 Removing the press rollerRemoving the laser scanner unit and the eraser lamp 28 Removing the LSU plate27 Removing the laser scanner unit Removing the eraser lamp Removing the main charger unit Troubleshooting Contents Error messages 1 Indicators and control keysMessages Normal messages Remote Operation Panel displayMaintenance messages Open the printer and clear the paper Printer’s memory is running low Continue due to complex data Service error indications Main motor errorLaser scanner unit Polygon motor error Call service 4000nnnnnnYes Replace main board KP-888. See End Turn power switch on Laser scanner unit Pin photo diode error Call service 4200nnnnnnYes End Replace engine board KP-882. See Eraser lamp error Call service 5300nnnnnnFuser unit error Call service 6000nnnnnnCall service 7980nnnnnn F010 Controller checksum error F020 Controller RAM read/write error11 F040 Communication error 10 F030 Controller system error12 F050 Engine ROM checksum error Background Print quality problemsBlack horizontal 6 Black vertical Unsharpness Gray Streaks Dirt on the top edge or back of the paperCompletely blank printout All-black printout ABC ABC Black horizontal streaksBlack vertical streaks Unsharpness Gray background Dirt on the top edge or back of the paper Repetitive defects gauge 2 Repetitive defects gaugeCorrecting a paper jam Jam at the face-down and face-up traysJam at the paper cassette 4 Jam at the paper cassette Jam inside the printerAppendix a D i a g r a m s Appendix a Contents Timing charts Option paper cassette feeding, two A4 size papersOption paper cassette feeding, two legal size papers OutpenOption paper cassette feeding, two letter size papers MP tray feeding, two A4 size papers MpfsolMP tray feeding, two legal size papers MP tray feeding, two letter size papers Wiring diagram Boardfeed 794KPG e Appendix B S t a t u sAppendix B Contents Status Printing the service statusGo key Service information on the status Details of service informationService information Top margin Inches+1/100 inches Frpo L1/L2 Engine parameter setting Hexadecimal, 32 bytes 64 digits Appendix C I n t e r f a c e Appendix C Contents Selecting the parallel interface mode Parallel interfaceTerminal Signal Parallel interface pin assignmentParallel interface signals Signal MeaningUSB interface USB interface pin assignmentChanging the serial interface configuration Serial interface OptionalFS-1010 RS-232C interface voltage levels Serial interface signalsRS-422A interface voltage levels RS-232C For computers with a DB-9 connector Connector configurationsRS-232C For computers with a DB-25 connector RS-422A ProtocolKyocera Mita Corporation Kyocera Mita AMERICA, INC

Related manuals

Manual 93 pages 8.47 Kb