Kyocera FS-1020D manual Paper Jam Removal, Jam at the Face-down Tray and the Rear Cover

Page 40

Paper Jam Removal

3.4Paper Jam Removal

This section describes how to remove paper when it jams in the printer. The printer will stop whenever paper jams in the printer or paper is not fed

from a paper cassette. The printer will go offline and (paper jam) indicator will light in the operator panel. When a jam occurs, check the points indicated in the following and clear the jam as indicated.

If paper jams occur frequently, try using a different type of paper, replace with paper from another ream, turn the stack of paper over, or turn the paper the other way around. Read the information in Chapter 4. Also, look for tiny pieces of paper that may have been torn apart and overlooked when the jammed paper was removed.

￿￿￿￿If you cannot solve the problem by changing the paper, there may be a problem with the printer. Call a service person.

•When pulling the paper, pull it gently so as not to tear it. Torn pieces of paper are difficult to remove and may be easily overlooked, deterring the jam recovery.

•Depending on where the jam occurred, the printer may or may not reprint the jammed page.

3.4.1Jam at the Face-down Tray and the Rear Cover

If paper is not completely ejected and has stopped only part way out, open the rear cover and remove the jammed paper by pulling it out. Open and close the printer’s top cover to clear the error. The printer then automatically warms up and resumes printing.

Rear Cover

Figure 3-1

3-15

Page 39 Page 41
Image 40
Page 39 Page 41
Contents FS-1020D Regarding Tradenames Limited Warranty LicenseLimitation of Remedies GeneralTypeface Trademark Acknowledgement Agfa Japan License Agreement GuidelinesContents Fonts Appendix C Printer Specifications Introduction Guide to the Manuals DescriptionGuide to the Operation Guide Basic Operations Operator Panel Column of the table on the followingIndicators KeysReference Name Status Meaning Reference Name FunctionUnderstanding the Status Firmware versionInstallation Options Error LogSoftware Version Hardware InformationInterface Information KIR Test PatternMaintenance Toner Container Replacement Interval Toner Container ReplacementReplacement Replenishing Toner Bag and dispose of itTake the new toner container from the bag. Hold it with Container at the positions marked Push Here until you hear Cleaning the Printer Printer InteriorFront Cover Lift the process unit together with the toner container outNever stand the process unit on end RollerCleaner Home Position Next time you use the printerCorners of the top cover Troubleshooting General Guide for Troubleshooting Symptom Check Items Corrective ActionPrint Quality Problems Check the EcoPrint setting Toner indicatorTry setting the thin paper mode Adjust the corresponding custom paper typeCheck the paper size setting Check the file or programIndicators Maintenance Messages Indicator KM-NET for Clients display Corrective Action Resolution because there is not enoughThere is no cassette in the feeder, or Cassette is not inserted properlyScanner pin-photo error 4200 error Errors Requiring Service Personnel AttentionEraser error 5300 error Controller check sum error F010 error Waste toner reservoir is full 7990 errorController RAM read/write error F020 error Engine ROM check sum error F050 error Error Messages Indicator KM-NET for Corrective Action Printer power is onMake sure to turn the printer power off before inserting This message appears when the printer is in the readyNormal Indicator Display Following displays appear during normal printer operationPaper Jam Removal Jam at the Face-down Tray and the Rear CoverJam at the Paper Cassette Jam at the DuplexerPull the paper cassette all the way out of the printer Jam Inside the Printer Normal paper running direction Jam at the MP TrayTo the MP tray. Instead, proceed to the next step Open the printer’s top and front covers RegistrationRegistration RollerMetalRollerMetal Paper Selection Paper Specifications SpecificationGeneral Guidelines Paper AvailabilityCondition of the Paper Selecting the Right PaperComposition Basis Weight Paper SizeSmoothness SizeThickness Caliper Moisture ContentPaper Grain Other Paper Properties Transparency overhead projection film Special PaperCheck that printing quality is satisfactory Adhesive-Backed Labels Top sheet white bond paper Adhesive Carrier sheetPostcards EnvelopesThick Paper Colored PaperPreprinted Paper Recycled PaperMP Tray Paper Paper Weight Cassette Paper TypeFonts Internal Fonts List of Fonts Internal Scalable and Bitmap Fonts and Kpdl FontsList of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Available Options Expansion Memory Installation Expansion memory should be installed only by a Kyocera MitaShall not be liable for damage due to improper installation Expansion memoryInstalling the Dimm Dimm to be usedInsert the Dimm into the Dimm socket so that the notches on Dimm align with the corresponding protrusions in the slotTesting the Expansion Memory Fasten it with the screwSetting the Printer Driver PropertiesMemory CompactFlash Card Again to restart the printerPush it in all the way Figure A-13Interface card Network Interface CardRemoved in step Appendix B Host Computer Interface Auto default Parallel InterfaceNibble high NormalPin In/out Description 0V DCData 0 1 to Data 7 8 Pins 2 to Paper Empty PError PinReset nInit Pin Error* nFault PinSelect In nSelectIn Pin USB Interface Serial Interface Option DTR Data Terminal Ready Pin SG Signal Ground PinRS-232C Interface Voltage Levels RS-232C Protocol H1 Baud rateH2 Data bits H3 Stop bitsH5 Protocol logic H6 Buffer nearly-full thresholdH7 Buffer nearly-empty threshold H8 Received-data buffer sizeRS-232C Cable Connection Obtain a Suitable RS-232C CableDouble click on Communications Port \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Power requirements Power consumptionDimensions WeightGlossary Cassette mode First modeIEEE1284 Dpi dots per inchPrescribe commands MP trayParallel interface OfflineStatus Sleep modeUSB Universal Serial Bus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3 2003 Is a trademark of Kyocera Corporation

FS-1020D specifications

The Kyocera FS-1020D is a compact and efficient monochrome laser printer that is perfect for small office environments or personal use. Renowned for its reliability and the quality of its printing, this device combines advanced technologies with user-friendly features to enhance productivity.

One of the standout features of the FS-1020D is its compact design, which allows it to fit comfortably in limited spaces without sacrificing performance. With dimensions that make it easy to position on a desk or shelf, this printer caters well to those who require a powerful yet unobtrusive printing solution.

Printing at a speed of up to 20 pages per minute, the FS-1020D ensures that documents are produced quickly and efficiently, minimizing downtime and waiting periods. Its ability to handle a monthly duty cycle of up to 30,000 pages makes it suitable for multiple users, providing robust support for busy work environments.

The FS-1020D employs Kyocera's exceptional Laser Print Technology, which guarantees sharp text and detailed graphics, ideal for both professional documents and personal use. The resolution of 1200 x 1200 dpi ensures that prints are crisp and clear, which is vital for high-quality output. Additionally, the printer is equipped with an automatic duplexing feature, allowing users to print on both sides of the paper, thus reducing paper usage and contributing to sustainability efforts.

Another important characteristic of the FS-1020D is its compatibility with various operating systems, including Windows and Mac, allowing users flexibility when it comes to integration into existing workflows. The printer connects via USB, providing a straightforward setup for users without the complications often associated with network printers.

In terms of maintenance, the FS-1020D is designed for ease of use. Its long-lasting toner cartridges serve approximately 2,500 pages, significantly lowering the cost per print and eliminating the need for frequent replacements. This makes the printer an economical choice in the long run, particularly for small businesses looking to keep overhead costs manageable.

Overall, the Kyocera FS-1020D represents a blend of efficiency, quality, and practicality, making it a reliable choice for users in need of a dependable monochrome laser printer. Its compact design, impressive performance, and low operating costs position it as an attractive solution for a variety of printing needs.
Top Page Image Contents