Kyocera FS-1020D H5 Protocol logic, H6 Buffer nearly-full threshold, H8 Received-data buffer size

Page 84

RS-232C Protocol

H5: Protocol logic

Parameter value

Meaning

0

Combination of 1 and 3 below

 

 

1

DTR/DSR, positive logic

 

 

2

DTR/DSR, negative logic

 

 

3

XON/XOFF

 

 

4

ETX/ACK

 

 

5

XON/XOFF recognized only as protocol

 

 

The factory setting is 0.

H6: Buffer nearly-full threshold

This is a percentage from 0 to 99. The factory setting is 90.

H7: Buffer nearly-empty threshold

This is a percentage from 0 to 99. The factory setting is 70.

The factory settings of the buffer nearly-full and nearly-empty thresholds (H6 and H7) are subject to change without notification.

The gap between the nearly-full and nearly-empty thresholds allows the computer to send a fairly large amount of data in a continuous stream.

H8: Received-data buffer size

This is the size of the input buffer, specified in units of 10 Kbytes. The factory-set value is 6, meaning 60 Kbytes.

B.4.1 PRESCRIBE FRPO D0 Command

The PRESCRIBE FRPO D0 command provides control over XON/XOFF operation when an error occurs on the serial interface. The following table summarizes the error status corresponding to different D0 values.

 

 

Serial interface error

 

 

Error not

Error handled

 

 

handled

 

Timing of XON

XON sent every

D0=0 (default)

D0=1

transfer to host

3-5 seconds

 

 

while Ready or

 

 

 

XON not sent

D0=10

D0=11

Waiting

 

 

 

 

 

 

 

Table B-4

 

 

 

B-10

Page 83 Page 85
Image 84
Page 83 Page 85
Contents FS-1020D Regarding Tradenames Limited Warranty LicenseLimitation of Remedies GeneralTypeface Trademark Acknowledgement Agfa Japan License Agreement GuidelinesContents Fonts Appendix C Printer Specifications Introduction Guide to the Manuals DescriptionGuide to the Operation Guide Basic Operations Operator Panel Column of the table on the followingIndicators KeysReference Name Status Meaning Reference Name FunctionUnderstanding the Status Firmware versionInstallation Options Error LogSoftware Version Hardware InformationInterface Information KIR Test PatternMaintenance Toner Container Replacement Toner Container Replacement IntervalReplacement Replenishing Toner Bag and dispose of itTake the new toner container from the bag. Hold it with Container at the positions marked Push Here until you hear Cleaning the Printer Printer InteriorFront Cover Lift the process unit together with the toner container outNever stand the process unit on end RollerCleaner Home Position Next time you use the printerCorners of the top cover Troubleshooting General Guide for Troubleshooting Symptom Check Items Corrective ActionPrint Quality Problems Check the EcoPrint setting Toner indicatorTry setting the thin paper mode Adjust the corresponding custom paper typeCheck the paper size setting Check the file or programIndicators Maintenance Messages Indicator KM-NET for Clients display Corrective Action Resolution because there is not enoughThere is no cassette in the feeder, or Cassette is not inserted properlyErrors Requiring Service Personnel Attention Scanner pin-photo error 4200 errorEraser error 5300 error Waste toner reservoir is full 7990 error Controller check sum error F010 errorController RAM read/write error F020 error Engine ROM check sum error F050 error Error Messages Indicator KM-NET for Corrective Action Printer power is onMake sure to turn the printer power off before inserting This message appears when the printer is in the readyNormal Indicator Display Following displays appear during normal printer operationPaper Jam Removal Jam at the Face-down Tray and the Rear CoverJam at the Paper Cassette Jam at the DuplexerPull the paper cassette all the way out of the printer Jam Inside the Printer Jam at the MP Tray Normal paper running directionTo the MP tray. Instead, proceed to the next step Open the printer’s top and front covers RegistrationRegistration RollerMetalRollerMetal Paper Selection Paper Specifications SpecificationGeneral Guidelines Paper AvailabilitySelecting the Right Paper Condition of the PaperComposition Basis Weight Paper SizeSmoothness SizeMoisture Content Thickness CaliperPaper Grain Other Paper Properties Special Paper Transparency overhead projection filmCheck that printing quality is satisfactory Adhesive-Backed Labels Top sheet white bond paper Adhesive Carrier sheetPostcards EnvelopesThick Paper Colored PaperPreprinted Paper Recycled PaperMP Tray Paper Paper Weight Cassette Paper TypeFonts Internal Fonts List of Fonts Internal Scalable and Bitmap Fonts and Kpdl FontsList of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Available Options Expansion Memory Installation Expansion memory should be installed only by a Kyocera MitaShall not be liable for damage due to improper installation Expansion memoryInstalling the Dimm Dimm to be usedInsert the Dimm into the Dimm socket so that the notches on Dimm align with the corresponding protrusions in the slotTesting the Expansion Memory Fasten it with the screwSetting the Printer Driver PropertiesMemory CompactFlash Card Again to restart the printerPush it in all the way Figure A-13Network Interface Card Interface cardRemoved in step Appendix B Host Computer Interface Auto default Parallel InterfaceNibble high NormalPin In/out Description 0V DCData 0 1 to Data 7 8 Pins 2 to Paper Empty PError PinReset nInit Pin Error* nFault PinSelect In nSelectIn Pin USB Interface Serial Interface Option SG Signal Ground Pin DTR Data Terminal Ready PinRS-232C Interface Voltage Levels RS-232C Protocol H1 Baud rateH2 Data bits H3 Stop bitsH5 Protocol logic H6 Buffer nearly-full thresholdH7 Buffer nearly-empty threshold H8 Received-data buffer sizeRS-232C Cable Connection Obtain a Suitable RS-232C CableDouble click on Communications Port \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Power requirements Power consumptionDimensions WeightGlossary Cassette mode First modeIEEE1284 Dpi dots per inchPrescribe commands MP trayParallel interface OfflineSleep mode StatusUSB Universal Serial Bus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3 2003 Is a trademark of Kyocera Corporation

FS-1020D specifications

The Kyocera FS-1020D is a compact and efficient monochrome laser printer that is perfect for small office environments or personal use. Renowned for its reliability and the quality of its printing, this device combines advanced technologies with user-friendly features to enhance productivity.

One of the standout features of the FS-1020D is its compact design, which allows it to fit comfortably in limited spaces without sacrificing performance. With dimensions that make it easy to position on a desk or shelf, this printer caters well to those who require a powerful yet unobtrusive printing solution.

Printing at a speed of up to 20 pages per minute, the FS-1020D ensures that documents are produced quickly and efficiently, minimizing downtime and waiting periods. Its ability to handle a monthly duty cycle of up to 30,000 pages makes it suitable for multiple users, providing robust support for busy work environments.

The FS-1020D employs Kyocera's exceptional Laser Print Technology, which guarantees sharp text and detailed graphics, ideal for both professional documents and personal use. The resolution of 1200 x 1200 dpi ensures that prints are crisp and clear, which is vital for high-quality output. Additionally, the printer is equipped with an automatic duplexing feature, allowing users to print on both sides of the paper, thus reducing paper usage and contributing to sustainability efforts.

Another important characteristic of the FS-1020D is its compatibility with various operating systems, including Windows and Mac, allowing users flexibility when it comes to integration into existing workflows. The printer connects via USB, providing a straightforward setup for users without the complications often associated with network printers.

In terms of maintenance, the FS-1020D is designed for ease of use. Its long-lasting toner cartridges serve approximately 2,500 pages, significantly lowering the cost per print and eliminating the need for frequent replacements. This makes the printer an economical choice in the long run, particularly for small businesses looking to keep overhead costs manageable.

Overall, the Kyocera FS-1020D represents a blend of efficiency, quality, and practicality, making it a reliable choice for users in need of a dependable monochrome laser printer. Its compact design, impressive performance, and low operating costs position it as an attractive solution for a variety of printing needs.
Top Page Image Contents