Kyocera FS-1020D manual Thickness Caliper, Moisture Content, Paper Grain

Page 51

Selecting the Right Paper

Thickness (Caliper)

Thick paper is referred to as high-caliper paper and thin paper as low- caliper paper. The paper used with the printer should be neither extremely thick nor extremely thin. If you are having problems with paper jams, multiple feeds, and faint printing, the paper you are using may be too thin. If you are having problems with paper jams and blurred printing the paper may be too thick. The proper thickness is 0.086 to 0.110 mm (3.4 to 4.3 mils).

Moisture Content

Moisture content is defined as the percent ratio of moisture to the dry mass of the paper. Moisture can affect the paper’s appearance, feedability, curl, electrostatic properties, and toner fusing characteristics.

The moisture content of the paper varies with the relative humidity in the room. When the relative humidity is high and the paper absorbs moisture, the paper edges expand, becoming wavy in appearance. When the relative humidity is low and the paper loses moisture, the edges shrink and tighten, and print contrast may suffer.

Wavy or tight edges can cause misfeeding and alignment anomalies. The moisture content of the paper should be 4 to 6%.

To ensure the proper moisture content it is important to store the paper in a controlled environment. Some tips on moisture control are:

Store paper in a cool, dry location.

Keep the paper in its wrapping as long as possible. Rewrap paper that is not in use.

Store paper in its original carton. Place a pallet etc. under the carton to separate it from the floor.

After removing paper from storage, let it stand in the same room as the printer for 48 hours before use.

Avoid leaving paper where it is exposed to heat, sunlight, or damp.

Paper Grain

When paper is manufactured, it is cut into sheets with the grain running parallel to the length (long grain) or parallel to the width (short grain). Short grain paper can cause feeding problems in the printer. All paper used in the printer should be long grain.

4-5

Image 51
Contents FS-1020D Regarding Tradenames General Limited WarrantyLicense Limitation of RemediesAgfa Japan License Agreement Guidelines Typeface Trademark AcknowledgementContents Fonts Appendix C Printer Specifications Introduction Description Guide to the ManualsGuide to the Operation Guide Basic Operations Column of the table on the following Operator PanelReference Name Function IndicatorsKeys Reference Name Status MeaningFirmware version Understanding the StatusHardware Information Installation OptionsError Log Software VersionKIR Test Pattern Interface InformationMaintenance Toner Container Replacement Toner Container Replacement IntervalReplacement Bag and dispose of it Replenishing TonerTake the new toner container from the bag. Hold it with Container at the positions marked Push Here until you hear Lift the process unit together with the toner container out Cleaning the PrinterPrinter Interior Front CoverRoller Never stand the process unit on endNext time you use the printer Cleaner Home PositionCorners of the top cover Troubleshooting Symptom Check Items Corrective Action General Guide for TroubleshootingPrint Quality Problems Adjust the corresponding custom paper type Check the EcoPrint settingToner indicator Try setting the thin paper modeCheck the file or program Check the paper size settingIndicators Maintenance Messages Cassette is not inserted properly Indicator KM-NET for Clients display Corrective ActionResolution because there is not enough There is no cassette in the feeder, orErrors Requiring Service Personnel Attention Scanner pin-photo error 4200 errorEraser error 5300 error Waste toner reservoir is full 7990 error Controller check sum error F010 errorController RAM read/write error F020 error Engine ROM check sum error F050 error Error Messages This message appears when the printer is in the ready Indicator KM-NET for Corrective ActionPrinter power is on Make sure to turn the printer power off before insertingFollowing displays appear during normal printer operation Normal Indicator DisplayJam at the Face-down Tray and the Rear Cover Paper Jam RemovalJam at the Duplexer Jam at the Paper CassettePull the paper cassette all the way out of the printer Jam Inside the Printer Jam at the MP Tray Normal paper running directionTo the MP tray. Instead, proceed to the next step Open the printer’s top and front covers RegistrationRegistration RollerMetalRollerMetal Paper Selection Paper Availability Paper SpecificationsSpecification General GuidelinesSelecting the Right Paper Condition of the PaperComposition Size Basis WeightPaper Size SmoothnessMoisture Content Thickness CaliperPaper Grain Other Paper Properties Special Paper Transparency overhead projection filmCheck that printing quality is satisfactory Top sheet white bond paper Adhesive Carrier sheet Adhesive-Backed LabelsEnvelopes PostcardsRecycled Paper Thick PaperColored Paper Preprinted PaperPaper Type MP Tray Paper Paper Weight CassetteFonts Internal Fonts Internal Scalable and Bitmap Fonts and Kpdl Fonts List of FontsList of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Available Options Expansion memory Expansion Memory InstallationExpansion memory should be installed only by a Kyocera Mita Shall not be liable for damage due to improper installationDimm to be used Installing the DimmDimm align with the corresponding protrusions in the slot Insert the Dimm into the Dimm socket so that the notches onFasten it with the screw Testing the Expansion MemoryProperties Setting the Printer DriverAgain to restart the printer Memory CompactFlash CardFigure A-13 Push it in all the wayNetwork Interface Card Interface cardRemoved in step Appendix B Host Computer Interface Normal Auto defaultParallel Interface Nibble high0V DC Pin In/out DescriptionError* nFault Pin Data 0 1 to Data 7 8 Pins 2 toPaper Empty PError Pin Reset nInit PinSelect In nSelectIn Pin USB Interface Serial Interface Option SG Signal Ground Pin DTR Data Terminal Ready PinRS-232C Interface Voltage Levels H3 Stop bits RS-232C ProtocolH1 Baud rate H2 Data bitsH8 Received-data buffer size H5 Protocol logicH6 Buffer nearly-full threshold H7 Buffer nearly-empty thresholdObtain a Suitable RS-232C Cable RS-232C Cable ConnectionDouble click on Communications Port \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Weight Power requirementsPower consumption DimensionsGlossary Dpi dots per inch Cassette modeFirst mode IEEE1284Offline Prescribe commandsMP tray Parallel interfaceSleep mode StatusUSB Universal Serial Bus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3 2003 Is a trademark of Kyocera Corporation

FS-1020D specifications

The Kyocera FS-1020D is a compact and efficient monochrome laser printer that is perfect for small office environments or personal use. Renowned for its reliability and the quality of its printing, this device combines advanced technologies with user-friendly features to enhance productivity.

One of the standout features of the FS-1020D is its compact design, which allows it to fit comfortably in limited spaces without sacrificing performance. With dimensions that make it easy to position on a desk or shelf, this printer caters well to those who require a powerful yet unobtrusive printing solution.

Printing at a speed of up to 20 pages per minute, the FS-1020D ensures that documents are produced quickly and efficiently, minimizing downtime and waiting periods. Its ability to handle a monthly duty cycle of up to 30,000 pages makes it suitable for multiple users, providing robust support for busy work environments.

The FS-1020D employs Kyocera's exceptional Laser Print Technology, which guarantees sharp text and detailed graphics, ideal for both professional documents and personal use. The resolution of 1200 x 1200 dpi ensures that prints are crisp and clear, which is vital for high-quality output. Additionally, the printer is equipped with an automatic duplexing feature, allowing users to print on both sides of the paper, thus reducing paper usage and contributing to sustainability efforts.

Another important characteristic of the FS-1020D is its compatibility with various operating systems, including Windows and Mac, allowing users flexibility when it comes to integration into existing workflows. The printer connects via USB, providing a straightforward setup for users without the complications often associated with network printers.

In terms of maintenance, the FS-1020D is designed for ease of use. Its long-lasting toner cartridges serve approximately 2,500 pages, significantly lowering the cost per print and eliminating the need for frequent replacements. This makes the printer an economical choice in the long run, particularly for small businesses looking to keep overhead costs manageable.

Overall, the Kyocera FS-1020D represents a blend of efficiency, quality, and practicality, making it a reliable choice for users in need of a dependable monochrome laser printer. Its compact design, impressive performance, and low operating costs position it as an attractive solution for a variety of printing needs.