NEC PA242W user manual English-24

Page 26

 

 

HOT KEY*2

When this function is activated; the brightness of the monitor can be adjusted without

 

 

 

entering the OSD menu by using the front buttons.

 

 

 

The “LEFT” or “RIGHT” buttons adjust the brightness level.

 

 

 

When this function is set to OFF, some buttons are disabled. See page 11.

 

 

 

 

 

 

FACTORY PRESET*2

Selecting FACTORY PRESET allows you to reset all OSD control settings back to the

 

 

 

factory settings. Highlighting the control to be reset and pressing the RESET button can

 

 

 

reset individual settings.

 

 

 

 

 

Tag8

PIP MODE

Selects PIP MODE, OFF/PIP/PICTURE BY PICTURE - ASPECT/PICTURE BY

 

 

 

PICTURE - FULL. See page 14.

 

 

 

 

 

 

PIP INPUT

Selects the PIP input signal.

 

 

 

 

 

 

PIP LEFT/RIGHT

When you select “PIP” in PIP MODE, you can control horizontal position of PIP display area.

 

 

 

 

 

 

PIP DOWN/UP

When you select “PIP” in PIP MODE, you can control vertical position of PIP display area.

 

 

 

 

 

 

PIP SIZE

Selects the size of the sub-picture used in PIP MODE.

 

 

 

 

 

 

BLANK SIGNAL SKIP

Skip no signal inputs when you change input signal with INPUT button.

 

 

 

 

 

 

OSD ROTATION

AUTO: The OSD rotates automatically when the monitor is rotated. OSD ROTATION is

 

 

 

set to AUTO by default.

 

 

 

LANDSCAPE: Display the OSD with landscape mode.

 

 

 

PORTRAIT: Display the OSD with portrait mode.

 

 

 

 

 

 

MAIN IMAGE

AUTO: The main window image automatically rotates according to the orientation of the

 

 

ROTATION

display.

 

 

 

OFF: The main window image is not rotated. MAIN IMAGE ROTATION is set to OFF by

 

 

 

default.

 

 

 

ON: The main window image always rotated.

 

 

 

Note: For PA272W/PA302W, this function is effective only if PICTURE BY PICTURE-

 

 

 

ASPECT or PICTURE BY PICTURE-FULL.

 

 

 

 

 

 

SUB IMAGE

AUTO: The sub window image automatically rotates according to the orientation of the

 

 

ROTATION

display.

 

 

 

OFF: The sub window image is not rotated. SUB IMAGE ROTATION is set to OFF by

 

 

 

default.

 

 

 

ON: The sub window image always rotated.

 

 

 

 

 

 

DDC/CI

DDC/CI ENABLE/DISABLE: Turns on or off the two way communication and control with

 

 

 

connected PC by video cable.

 

 

 

NOTE: Set DDC/CI to ENABLE when using hardware calibration software like

 

 

 

MultiProfi ler over DisplayPort, DVI or VGA.

 

 

 

 

 

 

SCREEN SAVER

Use the SCREEN SAVER to reduce the risk of image persistence.

 

 

 

MOTION (Default OFF): Screen image moves periodically in 4 directions in order to

 

 

 

reduce the risk of image retention.

 

 

 

Timing for MOTION can be set so the screen image moves in intervals from every

 

 

 

10 to 900 seconds. Timing is set in 10-second increments.

 

 

 

OPTION (Default REDUCED): There are two optional selections.

 

 

 

REDUCED: Screen image is reduced to 95% size and is moved periodically in

 

 

 

4 directions. Screen may appear slightly less sharp than normal. The full image appears

 

 

 

on the display.

 

 

 

NOTE: Some input signals may not be supported by REDUCED.

 

 

 

FULL: Screen image is set to FULL and is moved periodically in 4 directions. Screen

 

 

 

image goes outside of the display area in the direction that it shifts so that a portion of the

 

 

 

image may appear to be cut off.

 

 

 

NOTE: SCREEN SAVER works when ENABLE is OFF in TILE MATRIX and PIP MODE

 

 

 

is OFF.

 

 

 

 

 

Tag9*

INPUT SETTING*2

Video Band Width: Reduce the visual “noise” level of the input signal. It is strong

 

(Analog

 

ineffective, so that a number becomes small. Press “LEFT” or “RIGHT” to select.

 

input only)

 

Sync Threshold: Adjusts the slice level of a synchronization signal. Press “SELECT” to

 

 

 

move the adjustment menu. Adjusts the sensitivity of the separate or composite input

 

 

 

signals.

 

 

 

Try this option if the FINE adjustment does not successfully eliminate the noise.

 

 

 

Clamp position: Operating your monitor at a non-standard timing may cause images to

 

 

 

appear darker than normal or have color distortion. Use of the Clamp position control will

 

 

 

adjust images to their normal state.

 

 

 

 

*

Only for PA242W.

 

*2

This item does not reset by FACTORY PRESET (Tag7).

English-24

Image 26
Contents MultiSync PA242W MultiSync PA272W MultiSync PA302W Index English-37English-1 Declaration of Conformity Registration InformationFCC Information English-2English-3 Safety Precautions and MaintenanceRecommended use Ergonomics Cleaning the LCD PanelCleaning the Cabinet English-4Product Features ContentsQuick Start English-6English-7 USB downstream*2 Highest Stand PositionRaise and Lower Monitor Screen English-8Swivel Screen RotationTilt English-9Mount Flexible arm Flexible Arm InstallationRemove Monitor Stand for Mounting English-10Controls English-11Image Controls Auto Adjust Analog input onlyBrightness/Contrast Controls English-12Color Control Systems English-13English-14 ToolsMain Image Rotation on / SUB Image Rotation on Menu Tools English-15OSD Warning ECO InformationInformation English-16English-17 Using the Picture Mode functionType of Preset To exit the advanced menu Method To access the advanced menuAdvanced OSD English-18English-19 English-20 English-21 English-22 English-23 English-24 English-25 English-26 Specifications PA242WMonitor Specifications MultiSync PA242W English-27 Specifications PA272WMonitor Specifications MultiSync PA272W English-28 Specifications PA302WMonitor Specifications MultiSync PA302W Features English-29Troubleshooting No Video Picture is not as brightDisplay image is not sized properly Brightness variations over timeUsing the Auto Brightness function English-32Self Calibration PA302W only English-33Figure S.3 English-34White Point Matching/Copy PA302W only English-35Figure C.6 English-36Energy Saving Manufacturer’s Recycling and Energy InformationDisposing of your old NEC product Weee Mark European Directive 2012/19/EU