Philips PT-F100NTE Lamp Runtime, Power Off Timer, Control Panel, Auto Setup, Direct Power On

Page 37
OPTION menu

OPTION menu

LAMP RUNTIME

You can check how long the lamp has been used.

NOTE:

•LAMP RUNTIME is a relevant matter for lamp replacement timing. See “Replacing the Lamp unit” on page 43.

•When the lamp unit is replaced with the new one (ET-LAF100), the setting will be reset to “0”.

POWER OFF TIMER

You can set the off timer to switch off the POWER of the projector after a certain period of time automatically when no signal is detected. Press I H to select the required period from 15 to 60 minutes at intervals of

5 minutes.

DISABLE

15 MIN.

 

 

 

 

60 MIN.

 

 

 

 

 

 

 

 

 

 

 

CONTROL PANEL

You can turn off the function of the control panel buttons on the projector body. Press I H to select the required option.

INVALID

Invalidate the control panel buttons

 

Confirmation screen will be

 

displayed.

VALID

Validate the control panel buttons

AUTO SETUP

You can turn off the AUTO SETUP function for when the COMPUTER signal is detected.

AUTO

When the projector detect a

 

COMPUTER signal, adjust the

 

projected image position

 

automatically for SIGNAL SEARCH,

 

DOT CLOCK and CLOCK PHASE.

BUTTON

Only when the AUTO SETUP button

 

is pressed, the projected image

 

position will be adjusted for DOT

 

CLOCK and CLOCK PHASE. See

 

“Remote control” on page 13.

20 MIN.

 

 

 

 

 

 

55 MIN.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

25 MIN.

 

 

 

 

 

 

50 MIN.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

30 MIN.

 

 

 

 

 

 

45 MIN.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

35 MIN.

 

 

 

 

 

 

40 MIN.

 

 

 

 

 

 

 

 

 

 

 

 

DIRECT POWER ON

You can switch the projector start up status for when the Mains lead is connected while the MAIN POWER is on, or for when the MAIN POWER is switched on while the Mains lead is connected. Press I H to select the required option.

OFF

The projector will start from the

 

standby mode or the projecting

 

mode.

ON

The projector will start from the

 

projecting mode.

NOTE:

• Usually the recommended setting is AUTO.

SIGNAL SEARCH

You can turn off the auto signal detecting system.

ON

Detect the input signal from the

 

terminals and project the image.

OFF

Deactive

NOTE:

•SIGNAL SEARCH is not available when any input signal is projecting.

•Usually the recommended setting is ON.

INSTALLATION

When installing the projector, select the projection method according to the projector position. Press I H to cycle through the options. See “Projection method” on page 17.

Settings

NOTE:

•When the projector is started from the projecting mode, pressing the POWER button procedure is skippable.

FRONT/DESK

Setting on a desk/floor and

projecting from front

 

FRONT/CEILING

Mounting in the ceiling and

projecting from front

 

REAR/DESK

Setting on a desk/floor and

projecting from rear

 

REAR/CEILING

Mounting in the ceiling and

projecting from rear

 

 

 

ENGLISH - 37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents PT-F100E LCD Projector Commercial UseOperating Instructions Model No. PT-F100NTEDear Panasonic Customer Important Safety NoticeENGLISH Important InformationFor business users in the European Union Important Safety NoticeInformation on Disposal in other Countries outside the European Union Declaration of Conformity Important Safety InformationDeclaration of Conformity DoC Konformitätserklärung KEImportant Infomation 1. Set up your projector Contents5. Adjust the image Important InformationMaintenance SettingsContents Settings Basic Operation Getting StartedWARNINGS Precautions with regard to safetyImportant Information CAUTIONS Precautions with regard to safetyCautions when installing Cautions when transportingCautions on use AccessoriesImportant Information INSTALLATION Minimum required setting screenRead this first LANGUAGEAbout Your Projector Remote controlAbout Your Projector Projector bodyTop and front view Control panela computer. Selectable for input About Your Projector Back and bottom viewand output by menu operation Calculation methods for screen dimensions Setting upScreen size and throw distance Getting StartedSetting up Front leg adjusters and throwing angleSetting on a desk/floor and projecting from front Setting on a desk/floor and projecting from rearLens shift and positioning Adjusting the Lens shift leverHorizontal shift Vertical shiftWhen the screen position is fixed Setting up Projector location rangeWhen the projector position is fixed Connections Connecting with computersBefore connection to the projector LAN terminalConnecting with VIDEO IN/S-VIDEO IN Connecting with AV equipmentConnecting with COMPONENT IN ConnectionsPOWER indicator Switching the projector on/offConnecting DisconnectingSwitching off the projector Switching on the projectorSwitching the projector on/off Projecting an image Selecting the input signalPositioning the image Setting up the image position automatically Remote control operationOperating range OperationUsing the laser pointer Switching the input signalRemote control operation Pressing the COMPUTER buttonRemote control operation Resetting to the factory default settingsSwitching the position Capturing an imageEnlarging the centred area Controlling the volume of the speakerEnlarging the image Shifting the centre pointOperating procedure Adjusting with the bar scale itemsSettings Menu NavigationMenu Navigation Main menu and Sub-menuENGLISH PICTURE MODE PICTURE menuCONTRAST BRIGHTNESSFor S-VIDEO/VIDEO signals DETAILED SETUPFor RGB signals PICTURE menuPOSITION menu CLOCK PHASEDOT CLOCK KEYSTONEFRAME LOCK RESIZINGPOSITION menu OPTION menu FILTER SETUPINPUT GUIDE COMPUTER2 SELECTAUTO SETUP POWER OFF TIMERDIRECT POWER ON SIGNAL SEARCHHIGHLAND VOLUMETEST PATTERN BLACKBOARDPASSWORD CHANGE INPUT PASSWORDAfter you change the password SECURITY menuItems in NETWORK menu NETWORK menuManaging the indicated problems TEMP, LAMP and FILTER IndicatorsLAMP indicator TEMP indicatorCleaning the projector Care and ReplacementBefore cleaning the projector Cleaning the outer surface of the projectorResetting the FILTER Care and ReplacementWhen to replace the Lamp unit Replacing the Lamp unitCare and Replacement Replacement procedure Ceiling mount bracket safeguardsInstalling the safety cable Removing and replacing the lamp unitShould any problem persist, contact your dealer TroubleshootingTechnical Information List of compatible signalsAppendix Communication settings Pin assignments and signal namesSerial terminal Technical InformationControl commands Technical Information Cable specificationsComputer connection guidance ProjectorSwitching input LAMP switchingsignals Input signalSpecifications Appendix Screen size and throw distance for 169 aspect ratio Trademark acknowledgements DimensionsFILTER REMAINING IndexINITIALISE ALL SelectingIndex Printed in Japan Web Site http//panasonic.netS0207-2067C
Top Page Image Contents