Philips PT-F100NTE Read this first, Minimum required setting screen, Language, Option, Highland

Page 12

Read this first

Read this first

Minimum required setting screen

When you start the projection for the first time, the minimum required setting screen for projection will be displayed.

LANGUAGE

Select the required language setting.

Preparation	LANGUAGE
Preparation
	SELECT
	ENTER

Press F G I H buttons of the Remote control or Control panel on the projector to highlight the required language, and press ENTER to proceed to the next setting.

OPTION

Select the current projection method and fan speed setting. If you need return to the previous setting, press the RETURTN button.

OPTION

INSTALLATION	FRONT/DESK
HIGHLAND	OFF
	RETURN
SELECT
	ENTER

INSTALLATION

Press I H buttons of the Remote control or Control panel on the projector to select the required installation method. Press G to proceed to the HIGHLAND setting.

	FRONT/DESK	Setting on a desk/floor and
	FRONT/DESK	projecting from front
		projecting from front
	FRONT/CEILING	Mounting in the ceiling and
	FRONT/CEILING	projecting from front
		projecting from front
	REAR/DESK	Setting on a desk/floor and
	REAR/DESK	projecting from rear
		projecting from rear
	REAR/CEILING	Mounting in the ceiling and
	REAR/CEILING	projecting from rear
		projecting from rear

HIGHLAND

If you use the projector at high elevation, the HIGHLAND setting need to be ON to set the fan speed high. Press I H to select the required option. If you need to return to the INSTALLATION, press F.

OFF	The fan speed is low.
ON	The fan speed is high.

NOTE:

•At 1 400 m (4 593 ft) above sea level, the setting must be ON.

•The loudness of fan noise depends on the HIGHLAND setting.

Press the ENTER button to start the projection.

Once you finish the minimum requirement setting, it will not be displayed again unless the projector is initialised. See “INITIALISE ALL” on page 38.

You can change the settings from the MAIN MENU. See “Menu Navigation” on page 29.

ENGLISH - 12

Image 12

Contents LCD Projector Commercial Use PT-F100EOperating Instructions Model No. PT-F100NTEImportant Safety Notice Dear Panasonic CustomerENGLISH Important InformationImportant Safety Notice For business users in the European UnionInformation on Disposal in other Countries outside the European Union Important Safety Information Declaration of ConformityDeclaration of Conformity DoC Konformitätserklärung KEImportant Infomation Contents 1. Set up your projector5. Adjust the image Important InformationSettings MaintenanceContents Settings Basic Operation Getting StartedPrecautions with regard to safety WARNINGSImportant Information Precautions with regard to safety CAUTIONSCautions when transporting Cautions when installingAccessories Cautions on useImportant Information Minimum required setting screen INSTALLATIONRead this first LANGUAGERemote control About Your ProjectorProjector body About Your ProjectorTop and front view Control panelAbout Your Projector Back and bottom view a computer. Selectable for inputand output by menu operation Setting up Calculation methods for screen dimensionsScreen size and throw distance Getting StartedFront leg adjusters and throwing angle Setting upSetting on a desk/floor and projecting from front Setting on a desk/floor and projecting from rearAdjusting the Lens shift lever Lens shift and positioningHorizontal shift Vertical shiftSetting up Projector location range When the screen position is fixedWhen the projector position is fixed Connecting with computers ConnectionsBefore connection to the projector LAN terminalConnecting with AV equipment Connecting with VIDEO IN/S-VIDEO INConnecting with COMPONENT IN ConnectionsSwitching the projector on/off POWER indicatorConnecting DisconnectingSwitching on the projector Switching off the projectorSwitching the projector on/off Selecting the input signal Projecting an imagePositioning the image Remote control operation Setting up the image position automaticallyOperating range OperationSwitching the input signal Using the laser pointerRemote control operation Pressing the COMPUTER buttonResetting to the factory default settings Remote control operationSwitching the position Capturing an imageControlling the volume of the speaker Enlarging the centred areaEnlarging the image Shifting the centre pointAdjusting with the bar scale items Operating procedureSettings Menu NavigationMain menu and Sub-menu Menu NavigationSettings PICTURE menu PICTURE MODECONTRAST BRIGHTNESSDETAILED SETUP For S-VIDEO/VIDEO signalsFor RGB signals PICTURE menuCLOCK PHASE POSITION menuDOT CLOCK KEYSTONERESIZING FRAME LOCKPOSITION menu FILTER SETUP OPTION menuINPUT GUIDE COMPUTER2 SELECTPOWER OFF TIMER AUTO SETUPDIRECT POWER ON SIGNAL SEARCHVOLUME HIGHLANDTEST PATTERN BLACKBOARDINPUT PASSWORD PASSWORD CHANGEAfter you change the password SECURITY menuNETWORK menu Items in NETWORK menuTEMP, LAMP and FILTER Indicators Managing the indicated problemsLAMP indicator TEMP indicatorCare and Replacement Cleaning the projectorBefore cleaning the projector Cleaning the outer surface of the projectorCare and Replacement Resetting the FILTERWhen to replace the Lamp unit Replacing the Lamp unitCeiling mount bracket safeguards Care and Replacement Replacement procedureInstalling the safety cable Removing and replacing the lamp unitTroubleshooting Should any problem persist, contact your dealerList of compatible signals Technical InformationAppendix Pin assignments and signal names Communication settingsSerial terminal Technical InformationTechnical Information Cable specifications Control commandsComputer connection guidance ProjectorLAMP switching Switching inputsignals Input signalSpecifications Appendix Screen size and throw distance for 169 aspect ratio Dimensions Trademark acknowledgementsIndex FILTER REMAININGINITIALISE ALL SelectingIndex Web Site http//panasonic.net Printed in JapanS0207-2067C