Philips PT-F100NTE PICTURE menu, Picture Mode, Contrast, Brightness, Colour, Tint, Sharpness

Page 32

PICTURE menu

PICTURE menu

Settings

Remote control

Control panel

See “Navigating through the MENU” on page 29. See “Main menu and Sub-menu” on page 30.

PICTURE MODE

Depending on the projection environment, you can use these preset parameter settings to optimise image projection. Press I H to cycle through the options.

	NATURAL	Reproduces the original colour
	NATURAL	of the image
		of the image
	STANDARD	Setting for a general image
	DYNAMIC	Bright and sharp setting
		Setting for when projecting on
	BLACKBOARD	a blackboard
	BLACKBOARD	See “BLACKBOARD” on
		See “BLACKBOARD” on
		page 38.

NOTE:

•It may take for a while until the selected mode is stabilised.

CONTRAST

You can adjust the contrast of the projected image. Adjust the BRIGHTNESS in advance if necessary.

LowerHigher

BRIGHTNESS

You can adjust the brightness of the projected image.

DarkerBrighter

COLOUR

You can adjust the colour saturation of the projected image. (Available with signals from VIDEO/S-VIDEO/ COMPONENT only)

LighterDarker

TINT

You can adjust the skin tone in the projected image. (Available with signals from VIDEO/S-VIDEO/ COMPONENT only)

More More

reddish greenish

SHARPNESS

You can adjust the sharpness of the projected image.

Less	More
sharp	sharp

COLOUR TEMPERATURE

You can adjust the white balance of the projected image.

LOW	More bluish
STANDARD	Balanced white
HIGH	More reddish

DAYLIGHT VIEW

You can keep the projected image bright and vivid even in well-lit rooms where the ambient light sources cannot be controlled, such as when a door opens or when window coverings fail to block out sunlight.

AUTO: Automatic adjustment

ON: Active

OFF: Deactive

NOTE:

•Do not cover the ALS (Ambient Luminance Sensor) of the projector. See “ALS (Ambient Luminance Sensor)” on page 14.

•AUTO is not available when INSTALLATION setting in OPTION menu is set to REAR/DESK or REAR/

CEILING.

ENGLISH - 32

Image 32

Contents LCD Projector Commercial Use PT-F100EOperating Instructions Model No. PT-F100NTEImportant Safety Notice Dear Panasonic CustomerENGLISH Important InformationInformation on Disposal in other Countries outside the European Union Important Safety NoticeFor business users in the European Union Important Safety Information Declaration of ConformityDeclaration of Conformity DoC Konformitätserklärung KEImportant Infomation Contents 1. Set up your projector5. Adjust the image Important InformationSettings MaintenanceContents Settings Basic Operation Getting StartedImportant Information Precautions with regard to safetyWARNINGS Precautions with regard to safety CAUTIONSCautions when transporting Cautions when installingImportant Information AccessoriesCautions on use Minimum required setting screen INSTALLATIONRead this first LANGUAGERemote control About Your ProjectorProjector body About Your ProjectorTop and front view Control paneland output by menu operation About Your Projector Back and bottom viewa computer. Selectable for input Setting up Calculation methods for screen dimensionsScreen size and throw distance Getting StartedFront leg adjusters and throwing angle Setting upSetting on a desk/floor and projecting from front Setting on a desk/floor and projecting from rearAdjusting the Lens shift lever Lens shift and positioningHorizontal shift Vertical shiftWhen the projector position is fixed Setting up Projector location rangeWhen the screen position is fixed Connecting with computers ConnectionsBefore connection to the projector LAN terminalConnecting with AV equipment Connecting with VIDEO IN/S-VIDEO INConnecting with COMPONENT IN ConnectionsSwitching the projector on/off POWER indicatorConnecting DisconnectingSwitching the projector on/off Switching on the projectorSwitching off the projector Positioning the image Selecting the input signalProjecting an image Remote control operation Setting up the image position automaticallyOperating range OperationSwitching the input signal Using the laser pointerRemote control operation Pressing the COMPUTER buttonResetting to the factory default settings Remote control operationSwitching the position Capturing an imageControlling the volume of the speaker Enlarging the centred areaEnlarging the image Shifting the centre pointAdjusting with the bar scale items Operating procedureSettings Menu NavigationMain menu and Sub-menu Menu NavigationMenu Navigation PICTURE menu PICTURE MODECONTRAST BRIGHTNESSDETAILED SETUP For S-VIDEO/VIDEO signalsFor RGB signals PICTURE menuCLOCK PHASE POSITION menuDOT CLOCK KEYSTONEPOSITION menu RESIZINGFRAME LOCK FILTER SETUP OPTION menuINPUT GUIDE COMPUTER2 SELECTPOWER OFF TIMER AUTO SETUPDIRECT POWER ON SIGNAL SEARCHVOLUME HIGHLANDTEST PATTERN BLACKBOARDINPUT PASSWORD PASSWORD CHANGEAfter you change the password SECURITY menuNETWORK menu Items in NETWORK menuTEMP, LAMP and FILTER Indicators Managing the indicated problemsLAMP indicator TEMP indicatorCare and Replacement Cleaning the projectorBefore cleaning the projector Cleaning the outer surface of the projectorCare and Replacement Resetting the FILTERWhen to replace the Lamp unit Replacing the Lamp unitCeiling mount bracket safeguards Care and Replacement Replacement procedureInstalling the safety cable Removing and replacing the lamp unitTroubleshooting Should any problem persist, contact your dealerAppendix List of compatible signalsTechnical Information Pin assignments and signal names Communication settingsSerial terminal Technical InformationTechnical Information Cable specifications Control commandsComputer connection guidance ProjectorLAMP switching Switching inputsignals Input signalSpecifications Appendix Screen size and throw distance for 169 aspect ratio Dimensions Trademark acknowledgementsIndex FILTER REMAININGINITIALISE ALL SelectingIndex S0207-2067C Web Site http//panasonic.netPrinted in Japan