Philips PT-F100NTE TEMP, LAMP and FILTER Indicators, Managing the indicated problems, Maintenance

Page 41
TEMP, LAMP and FILTER Indicators

TEMP, LAMP and FILTER Indicators

Managing the indicated problems

If a problem should occur with the projector, the TEMP, LAMP and/or

 

FILTER indicators will inform you. Manage the indicated problems as

 

follow.

 

1.

Confirm the status of all indicators and projector, and switch off the

 

 

projector in proper way.

 

2.

Find out the cause of the problem by status of the TEMP, LAMP

POWER LAMP TEMP FILTER

 

and/or FILTER indicators.

3.

Follow the instruction for each indication below and solve the

 

 

problem.

 

4.Turn on the projector in the correct way and confirm the indicator is not indicating a problem any longer.

NOTE:

• If no problem is found or the problem remains, do not turn on the projector. Instead contact an Authorised Service Centre.

LAMP indicator

Indicator

Illuminating RED

Flashing RED

 

 

 

 

 

 

 

Problem

LAMP RUNTIME has

LAMP circuit failure, abnormal function or Lamp unit is damaged.

reached 2 800 hours.

 

 

 

 

 

Lamp unit will run out

The MAIN POWER is

 

 

 

switched on again

LAMP circuit failure,

Lamp unit is

Cause

soon and needs to be

before the Lamp unit

abnormal function.

damaged.

 

replaced.

 

is cooled enough.

 

 

 

 

 

 

 

See “Replacing the

Let the Lamp unit cool

Contact an Authorised

See “Replacing the

Remedy

Lamp unit” on page 43.

down and turn on the

Service Centre.

Lamp unit” on page 43.

 

 

MAIN POWER.

 

 

TEMP indicator

Indicator

Illuminating RED and still projecting

 

 

Flashing RED and POWER is turned off

 

 

 

 

 

Problem

The temperature inside and/or outside the projector is abnormally high.

 

 

 

 

 

 

Cause

The ventilation

The room temperature

The ARF is excessively

The projector is located

openings are covered.

is too high.

dirty and the ventilation

at high elevations

 

is poor.

(above 1 400 m).

 

 

 

 

Remove the object(s)

Reinstall the projector

Replace the ARF in the

Turn on the projector*1

Remedy

from the ventilation

in temperature

proper method. See

and set the

openings or clear

controlled place. See

HIGHLAND to ON.

 

page 42.

 

around the projector.

page 50.

See page 38.

 

 

 

 

 

 

 

*1. The projector will perform only 2 minutes with OFF setting at high elevation.

FILTER indicator

When the FILTER indicator is flashing GREEN, the ARF is normally rolling up.

Indicator

Illuminating RED

Flashing RED

Illuminating ORANGE

Flashing ORANGE

 

 

 

 

 

 

FILTER REMAINING

The projector cannot

The ARF cannot

FILTER REMAINING

Problem

has turned red. See

has turned yellow. See

detect the ARF.

operate properly.

 

page 36.

page 36.

 

 

 

 

 

 

Foreign object is

 

Cause

ARF has been run out.

ARF is not attached.

blocking the ARF

ARF is running out.

 

 

 

operation.

 

 

See “Replacing the

 

Remove the foreign

 

 

 

object or contact an

Prepare the ARF for

Remedy

ARF (Auto Rolling

Attach the ARF.

Authorised Service

replacement.

 

Filter)” on page 42.

 

 

 

Centre.

 

 

 

 

 

 

 

 

 

 

Maintenance

ENGLISH - 41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents PT-F100E LCD Projector Commercial UseOperating Instructions Model No. PT-F100NTEDear Panasonic Customer Important Safety NoticeENGLISH Important InformationInformation on Disposal in other Countries outside the European Union Important Safety NoticeFor business users in the European Union Declaration of Conformity Important Safety InformationDeclaration of Conformity DoC Konformitätserklärung KEImportant Infomation 1. Set up your projector Contents5. Adjust the image Important InformationMaintenance SettingsContents Settings Basic Operation Getting StartedImportant Information Precautions with regard to safetyWARNINGS CAUTIONS Precautions with regard to safetyCautions when installing Cautions when transportingImportant Information AccessoriesCautions on use INSTALLATION Minimum required setting screenRead this first LANGUAGEAbout Your Projector Remote controlAbout Your Projector Projector bodyTop and front view Control paneland output by menu operation About Your Projector Back and bottom viewa computer. Selectable for input Calculation methods for screen dimensions Setting upScreen size and throw distance Getting StartedSetting up Front leg adjusters and throwing angleSetting on a desk/floor and projecting from front Setting on a desk/floor and projecting from rearLens shift and positioning Adjusting the Lens shift leverHorizontal shift Vertical shiftWhen the projector position is fixed Setting up Projector location rangeWhen the screen position is fixed Connections Connecting with computersBefore connection to the projector LAN terminalConnecting with VIDEO IN/S-VIDEO IN Connecting with AV equipmentConnecting with COMPONENT IN ConnectionsPOWER indicator Switching the projector on/offConnecting DisconnectingSwitching the projector on/off Switching on the projectorSwitching off the projector Positioning the image Selecting the input signalProjecting an image Setting up the image position automatically Remote control operationOperating range OperationUsing the laser pointer Switching the input signalRemote control operation Pressing the COMPUTER buttonRemote control operation Resetting to the factory default settingsSwitching the position Capturing an imageEnlarging the centred area Controlling the volume of the speakerEnlarging the image Shifting the centre pointOperating procedure Adjusting with the bar scale itemsSettings Menu NavigationMenu Navigation Main menu and Sub-menuMenu Navigation PICTURE MODE PICTURE menuCONTRAST BRIGHTNESSFor S-VIDEO/VIDEO signals DETAILED SETUPFor RGB signals PICTURE menuPOSITION menu CLOCK PHASEDOT CLOCK KEYSTONEPOSITION menu RESIZINGFRAME LOCK OPTION menu FILTER SETUPINPUT GUIDE COMPUTER2 SELECTAUTO SETUP POWER OFF TIMERDIRECT POWER ON SIGNAL SEARCHHIGHLAND VOLUMETEST PATTERN BLACKBOARDPASSWORD CHANGE INPUT PASSWORDAfter you change the password SECURITY menuItems in NETWORK menu NETWORK menuManaging the indicated problems TEMP, LAMP and FILTER IndicatorsLAMP indicator TEMP indicatorCleaning the projector Care and ReplacementBefore cleaning the projector Cleaning the outer surface of the projectorResetting the FILTER Care and ReplacementWhen to replace the Lamp unit Replacing the Lamp unitCare and Replacement Replacement procedure Ceiling mount bracket safeguardsInstalling the safety cable Removing and replacing the lamp unitShould any problem persist, contact your dealer TroubleshootingAppendix List of compatible signalsTechnical Information Communication settings Pin assignments and signal namesSerial terminal Technical InformationControl commands Technical Information Cable specificationsComputer connection guidance ProjectorSwitching input LAMP switchingsignals Input signalSpecifications Appendix Screen size and throw distance for 169 aspect ratio Trademark acknowledgements DimensionsFILTER REMAINING IndexINITIALISE ALL SelectingIndex S0207-2067C Web Site http//panasonic.netPrinted in Japan
Top Page Image Contents