Black Box 10BASE-T/100BASE-TX G.SHDSL Two-Wire Extender/NTU manual Installation, Connecting Power

Page 25

Installation

The RJ-45 DSL connector on the LB510A-R2’s twisted pair interface is polarity insen- sitive and is wired for a two-wire interface.

3.2 CONNECTING THE ETHERNET INTERFACE

This section describes how to connect the Ethernet ports to your network equipment.

The interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to volt-

age, current, anticipated temperature, flammability, and mechani- CAUTION cal serviceability.

The RJ-45 ports labeled Ethernet are the Auto-MDIX10/100Base-T interface. These ports are designed to connect directly to a 10/100Base-T device or network. You may connect these ports to a hub or PC using a straight through or crossover cable that is up to 328 ft long.

3.3 CONNECTING POWER

3.3.1 External AC universal power supply

1.Connect the power cord from the AC socket to the IEC-320 power entry connector on the universal input power supply.

CAUTION

The external AC adaptor shall be a listed limited power source that incorporates a disconnect device and shall be positioned within easy reach of the operator. Ensure that the AC power cable meets all applicable standards for the country in which it is to be installed, and that it is connected to a wall outlet which has earth ground.

2. Connect the barrel plug to the Power connector on the LB510A-R2.

NOTE: The LB510A-R2 powers up as soon as it is plugged into an AC outlet—there is no power switch.

724-746-5500 blackbox.com

Page 25

Image 25
Contents 10BASE-T/100BASE-TX G.SHDSL Two-Wire Extender/NTU Black Box G.SHDSL.bis EFM CPE Table of ContentsBlackbox.com Table of Contents Ethernet Port Radio Frequency Interference Statements Radio Frequency Interference StatementsInstrucciones DE Seguridad Normas Oficiales Mexicanas Electrical Safety StatementInstrucciones DE Seguridad Safety When Working with Electricity Blackbox.com General Information FeaturesDescription External AC universal power supply Power Input ConnectorSoftware CLI Configuration ConfigurationHardware DIP-SWITCH Configuration Configuration LB510A-R2 Configuring the DIP SwitchesDIP Switch Settings OFF System Reset ModeOn CO 704 2816 Ethernet Management Port DSL Line Condition Good or Poor Help CommandsSystem Status Commands System Configuration CommandsDSL Configuration Commands DSL Clear Errcntrs Command DSL Status CommandExample Command Line Interface Session Remote ConsoleSafety When Working With Electricity Connecting the DSL Interface InstallationConnecting the Ethernet Interface InstallationConnecting Power DC Power POWER-UPOperation LED Status MonitorsOperation Power GreenDSL Green Link GreenLoopbacks Test ModesRemote Console Operation Remote console operationPatterns Establishing a Remote Console Session How to ConnectIs a screenshot of opening a typical remote console session Differences in local and remote control session behavior How to DisconnectSoftware Upgrade Software UpgradeReset Configuration to Factory Defaults Reset configuration to factory defaults Power and Power Supply Specifications ConfigurationLine Coding Transmission LineLine Rates DSL Line Line InterfaceDimensions Temperature RangeHumidity AltitudeEthernet Port Interface Pinouts Line PortReset configuration to factory defaults Blackbox.com

LB510A-R2, 10BASE-T/100BASE-TX G.SHDSL Two-Wire Extender/NTU specifications

The Black Box LB510A-R2 is a highly efficient two-wire extender and Network Termination Unit (NTU) designed to facilitate high-speed data transmission over existing copper wiring. Ideal for extending Ethernet signals, this device supports both 10BASE-T and 100BASE-TX Ethernet standards, making it versatile for various networking applications. With the growing demand for reliable and high-speed internet connections, the LB510A-R2 provides a cost-effective solution for businesses seeking to extend their networks without the need for extensive rewiring.

One of the standout features of the LB510A-R2 is its ability to operate using G.SHDSL technology, which allows for symmetric data transfer rates over twisted pair copper lines. This technology offers a significant advantage compared to traditional DSL methods, as it supports higher bandwidths and provides a more stable connection suitable for various applications, including VoIP, video conferencing, and online collaboration tools. The LB510A-R2 can achieve data rates up to 5.7 Mbps, depending on the line conditions, making it an excellent choice for businesses that require reliable and efficient communication.

The device supports a range of distances for transmission, effectively functioning over maximum distances of up to 12,000 feet (3,600 meters) with appropriate line conditions. This long-distance capability allows organizations to spread their network over extensive areas without sacrificing data integrity or speed. The LB510A-R2 includes built-in functionality to automatically adjust the line rate based on the actual conditions of the copper wires, ensuring optimal performance.

In terms of installation and management, the Black Box LB510A-R2 features an intuitive interface with LED indicators that provide real-time status updates for system monitoring. The compact design and rack-mountable option make it easy to integrate into existing network infrastructures, minimizing space requirements while maximizing performance.

In summary, the Black Box LB510A-R2 10BASE-T/100BASE-TX G.SHDSL Two-Wire Extender/NTU represents a robust solution for extending network capabilities with its advanced features, including G.SHDSL technology, extensive transmission distance, and user-friendly management. Whether for a small office or a large enterprise, this device is instrumental in ensuring seamless connectivity in an increasingly digital world.