Black Box LB510A-R2 manual Establishing a Remote Console Session, How to Connect

Page 30

Black Box G.SHDSL.bis EFM CPE

Figure 10. Remote control session diagram

5.1 ESTABLISHING A REMOTE CONSOLE SESSION

5.1.1 How to Connect

The following steps are to establish a connection to the remote LB510A-R2 (far-end) via Remote Console Session (RCS):

1.Connect to the console port of the LB510A-R2 (near-end) via Telnet session.

2.At the password prompt, log in to the near-end LB510A-R2.

3.Ensure that a DSL link is established. You can verify an established DSL link by using the system show status command or by checking that the DSL LED is solid green. Upon executing the show status command, the dsl link state is shown as success if the DSL link is established.

4.At the command prompt, enter the command remote console.

5.Wait for the message Console: Remote console connection established.

-If a DSL link is not established, or for some other reason the LB510A-R2 (far- end) does not respond in a reasonable amount of time, the following message appears: Console: Remote console timed out trying to connect. Enter the com- mand remote console again.

-If LB510A-R2 (Far End) already has an active remote console session open, you will see the message Console: Remote console connection request rejected. This can also happen if the remote LB510A-R2 (far-end) has an established remote console session with the local LB510A-R2 (near-end) which has timed out.

6.Enter the password at the password prompt for the remote console session.

Page 30

724-746-5500 blackbox.com

Page 29 Page 31
Image 30
Page 29 Page 31
Contents 10BASE-T/100BASE-TX G.SHDSL Two-Wire Extender/NTU Table of Contents Black Box G.SHDSL.bis EFM CPEBlackbox.com Table of Contents Ethernet Port Radio Frequency Interference Statements Radio Frequency Interference StatementsNormas Oficiales Mexicanas Electrical Safety Statement Instrucciones DE SeguridadInstrucciones DE Seguridad Safety When Working with Electricity Blackbox.com Features General InformationDescription Power Input Connector External AC universal power supplyConfiguration Software CLI ConfigurationHardware DIP-SWITCH Configuration Configuration Configuring the DIP Switches LB510A-R2System Reset Mode DIP Switch Settings OFFOn CO 704 2816 Ethernet Management Port Help Commands DSL Line Condition Good or PoorSystem Configuration Commands System Status CommandsDSL Configuration Commands Example Command Line Interface Session DSL Status CommandDSL Clear Errcntrs Command Remote ConsoleSafety When Working With Electricity Installation Connecting the DSL InterfaceInstallation Connecting the Ethernet InterfaceConnecting Power Operation POWER-UPDC Power LED Status MonitorsDSL Green Power GreenOperation Link GreenTest Modes LoopbacksRemote console operation Remote Console OperationPatterns How to Connect Establishing a Remote Console SessionIs a screenshot of opening a typical remote console session How to Disconnect Differences in local and remote control session behaviorSoftware Upgrade Software UpgradeReset Configuration to Factory Defaults Reset configuration to factory defaults Configuration Power and Power Supply SpecificationsLine Rates DSL Line Transmission LineLine Coding Line InterfaceHumidity Temperature RangeDimensions AltitudeInterface Pinouts Line Port Ethernet PortReset configuration to factory defaults Blackbox.com

LB510A-R2, 10BASE-T/100BASE-TX G.SHDSL Two-Wire Extender/NTU specifications

The Black Box LB510A-R2 is a highly efficient two-wire extender and Network Termination Unit (NTU) designed to facilitate high-speed data transmission over existing copper wiring. Ideal for extending Ethernet signals, this device supports both 10BASE-T and 100BASE-TX Ethernet standards, making it versatile for various networking applications. With the growing demand for reliable and high-speed internet connections, the LB510A-R2 provides a cost-effective solution for businesses seeking to extend their networks without the need for extensive rewiring.

One of the standout features of the LB510A-R2 is its ability to operate using G.SHDSL technology, which allows for symmetric data transfer rates over twisted pair copper lines. This technology offers a significant advantage compared to traditional DSL methods, as it supports higher bandwidths and provides a more stable connection suitable for various applications, including VoIP, video conferencing, and online collaboration tools. The LB510A-R2 can achieve data rates up to 5.7 Mbps, depending on the line conditions, making it an excellent choice for businesses that require reliable and efficient communication.

The device supports a range of distances for transmission, effectively functioning over maximum distances of up to 12,000 feet (3,600 meters) with appropriate line conditions. This long-distance capability allows organizations to spread their network over extensive areas without sacrificing data integrity or speed. The LB510A-R2 includes built-in functionality to automatically adjust the line rate based on the actual conditions of the copper wires, ensuring optimal performance.

In terms of installation and management, the Black Box LB510A-R2 features an intuitive interface with LED indicators that provide real-time status updates for system monitoring. The compact design and rack-mountable option make it easy to integrate into existing network infrastructures, minimizing space requirements while maximizing performance.

In summary, the Black Box LB510A-R2 10BASE-T/100BASE-TX G.SHDSL Two-Wire Extender/NTU represents a robust solution for extending network capabilities with its advanced features, including G.SHDSL technology, extensive transmission distance, and user-friendly management. Whether for a small office or a large enterprise, this device is instrumental in ensuring seamless connectivity in an increasingly digital world.
Top Page Image Contents