Xerox FS 3270 instruction manual PCL mode, Ascii HEX, FSL mode, N2data, Y76

Page 52

Appendices

Xerox FS 3270, User's Guide

No.	Name	Syntax		Parameters	Deviations
75	Overwrite	PCL:		n1	PCL mode
	Translate	%Y75,<n1>[,n2],		00-BF = LU3 position
	Table	<data>[:n1,n2,		in HEX of
		<data>]%		character to
				be trans-
				lated
				n2
				1-8 = Symbol set
				defined in FSL
				74
				n3
				00-FF = Data in
				ASCII HEX
				required to
				print the
		-----------------		character
		-----------------		---------------------	--------
		FSL:		n1	FSL mode
		%Y75,n1,n2[;n2]		LU3 char.
		[:n1,n2]%		00-BF =
				Specifies which LU3
				characters to be
				translated to
				parameter n2
				n2(data)
				00-FF =
				ASCII code as the LU3
				value shall be
				translated to. Can be
				defined as paired HEX
				up to 12 bytes,
				separated with
				commas.
76	Create APL	%Y76,<n1>%		1-8 = Create an APL	Y76:
	Translate			Translate Table	FSL only
	Table
77	Reset APL	%Y77,<n1>%		1-8 = Reset the
	Translate			indicated APL
	Table			table
78	Select APL	%Y78,<n1>%		1-8 = Select the
	Translate			indicated APL
	Table			table

- 52 -

Image 52

Contents EMC directive TrademarksRelated Manuals PrefaceSeptember Table of Contents Table of Contents Xerox FS 3270, Users Guide Installation Requirements PCL Driver Default DriverIntroduction to Xerox FS PCL or FSL output driverXerox FS 3270 Features Non-IPCItems Supplied Supported Control UnitsXerox FS Changing Paper Size Default US/Europe IPC Upgrade KitOperating Environment Xerox FS 3270 IPCInstallation Requirements Xerox FS 3270, Users Guide Installation and Connections of the Xerox FS Rear PanelChanging the Printer Driver Serial inputConnecting the Xerox FS 3270 to the Printer Upgrading to IPCConnecting via Centronics output Connecting via RS-232 outputConnecting to System Xerox FS 3270, Users Guide Connecting the Xerox FS 3270 to the System What if the CU Indicator fails to turn on?Testing PCL driverTimeout Settings Printout at Power-on PCL mode onlyIndicators of the Xerox FS Operation of Xerox FSCU Contact with Control Unit PAR Parallel inputSER Serial input Ready Printer ReadySpecifying Timeout ??character??%%Y100,30,1B,45%%X1 IdaSetup IPC Programming IRQ Handling PrinterPCL Driver Default Programming Xerox FS 3270 non-IPCSetup Functions Supported in PCL mode Where % is the defined ESC character ESC FeaturesWhere % is the defined ESC character Send Logo User Settings Functions X-Functions Test functions T-FunctionsEngineering Functions FunctionsSetup Functions Supported in FSL mode ESC Features User Settings Functions X-Functions FSL Setup via Xerox FS 3270 Serial or Parallel Port ??%%Y249,PASSWORD%%Y100,10,’SHARESTRING’%%X1??%%Y100,10,’SHARESTRING’%%X1 Character conversionActivating the Y249 Engineering Function Limitations when Y249 is activeDeactivating the Y249 Engineering Function Updating Firmware Error Messages Recoverable ErrorsNot in engineering mode Non-Recoverable Hardware Errors Test Printouts Busy TimeoutPCL Test Printout Proportionally Spaced = Gfid CPI=Active Gfid = FSL Test Printout Appendix a Quick Reference Guide to FSL Functions FSL N/SLPI LPI FSL N/SEbcdic =FSL Y10=PCL Y13 Y12Are wrapped Y19 Y22FF after Y26,n1% = No FF Y35 Y39 EABY41 IRQ Y47ESC EEPROM/RAMEeprom Y52Y53 Y54Y55 Y56Y74 Y71HEX PCL mode FSL modeAscii HEX N2dataY79 APLName Syntax Parameters Deviations Y91 Y92Y93 Y94Y98 Y96APO Y111 Y110Y112 Y113 Y114Y115 Y118Re. T2 RAMData Use of Xerox FS 3270 serial port Appendix B Using Serial OUTExample Cable connections to HP LaserJet Appendix C Selected Xerox Products