Xerox FS 3270 instruction manual Y113, Y114, Y115, Y118, Y119

Page 58

Appendices

Xerox FS 3270, User's Guide

No.	Name	Syntax		Parameters			Deviations
113	idaAFP Early	%Y113,<n1>%		n1			Y113:
	Print			0	= All is printed		PCL only
	Complete				before response
					to host.
	This
	function			*1	= Early print-
	enables the				complete
	spool system				supported
	to make a
	better
	recovery
	after
	errors.
114	idaAFP	%Y114,<n1>%		n1			Y114:
	Colour			*0	= No colour		PCL only
	Support				support
					available
				1	= Support for
					colour printing
				2	= Colour by
					simulation
				9	= As 1, but with
					Pixel Placement
					Support
				10	= As 2, but with
					Pixel Placement
					Support
115	idaAFP Misc.	%Y115,<n1>%		n1			Y115:
				0	= No features		PCL only
					covered by this
					FSL available
				*1	= Support for Unit
					selection in
					printer
118	Expanded	%Y118,<n1>%			IIPC	Non-IIPC	Y118:
	Printable			*0= Disabled		Disabled	PCL only
	Area			1= Enabled		Disabled
				2= Disabled		Enabled
				3= Enabled		Enabled
119	Auto-	%Y119,<n1>%		n1			Y119:
	Configura			*0	= Disable Auto-		PCL only
	tion select				configuration
				2	= Auto-
					configuration
					via PJL

- 58 -

Image 58

Contents EMC directive TrademarksRelated Manuals PrefaceSeptember Table of Contents Table of Contents Xerox FS 3270, Users Guide Introduction to Xerox FS Installation RequirementsPCL Driver Default Driver PCL or FSL output driverXerox FS 3270 Features Non-IPCItems Supplied Supported Control UnitsXerox FS Operating Environment Changing Paper Size Default US/EuropeIPC Upgrade Kit Xerox FS 3270 IPCInstallation Requirements Xerox FS 3270, Users Guide Installation and Connections of the Xerox FS Rear PanelChanging the Printer Driver Serial inputConnecting the Xerox FS 3270 to the Printer Upgrading to IPCConnecting via Centronics output Connecting via RS-232 outputConnecting to System Xerox FS 3270, Users Guide Connecting the Xerox FS 3270 to the System What if the CU Indicator fails to turn on?Testing PCL driverTimeout Settings Printout at Power-on PCL mode onlyCU Contact with Control Unit Indicators of the Xerox FSOperation of Xerox FS PAR Parallel inputSER Serial input Ready Printer ReadySpecifying Timeout ??character??%%Y100,30,1B,45%%X1 IdaSetup IPC Programming IRQ Handling PrinterPCL Driver Default Programming Xerox FS 3270 non-IPCSetup Functions Supported in PCL mode Where % is the defined ESC character ESC FeaturesWhere % is the defined ESC character Send Logo Engineering Functions User Settings Functions X-FunctionsTest functions T-Functions FunctionsSetup Functions Supported in FSL mode ESC Features User Settings Functions X-Functions ??%%Y100,10,’SHARESTRING’%%X1 FSL Setup via Xerox FS 3270 Serial or Parallel Port??%%Y249,PASSWORD%%Y100,10,’SHARESTRING’%%X1 Character conversionActivating the Y249 Engineering Function Limitations when Y249 is activeDeactivating the Y249 Engineering Function Updating Firmware Error Messages Recoverable ErrorsNot in engineering mode Non-Recoverable Hardware Errors Test Printouts Busy TimeoutPCL Test Printout Proportionally Spaced = Gfid CPI=Active Gfid = FSL Test Printout LPI Appendix a Quick Reference Guide to FSL FunctionsFSL N/S LPI FSL N/SEbcdic =FSL Y10=PCL Y13 Y12Are wrapped Y19 Y22FF after Y26,n1% = No FF Y35 Y39 EABY41 IRQ Y47Eeprom ESCEEPROM/RAM Y52Y55 Y53Y54 Y56Y74 Y71HEX Ascii HEX PCL modeFSL mode N2dataY79 APLName Syntax Parameters Deviations Y93 Y91Y92 Y94Y98 Y96APO Y111 Y110Y112 Y115 Y113Y114 Y118Re. T2 RAMData Use of Xerox FS 3270 serial port Appendix B Using Serial OUTExample Cable connections to HP LaserJet Appendix C Selected Xerox Products