Xerox instruction manual Connecting to System Xerox FS 3270, Users Guide

Page 14

Connecting to System

Xerox FS 3270, User's Guide

If possible, the serial output device you are connecting has to be set to Baud rate = 9600, Number of data bits = 8, Parity = None and Stop Bits = 1 to match the default settings of the box. If this is not possible, you must change functions 15, 16, 17 and 18 on the box to match the settings of the serial output device.

NOTE:

Programming of Functions 15, 16, 17, 18 and 24 is not possible via the serial port. These functions have to be programmed either via the coax port or via the parallel input port.

For full details on Y functions, please see the Laser 3270 Programmer's Guide; Document No.: D62078, subpart D62071.

4.Power on the printer and the Xerox FS 3270 box.

5.Make a settings printout by turning the rotary switch to the “T” position and back to the original position. This will generate a settings printout. The CU indicator will start flashing for approximately 30 seconds.

Compare the test printout (FSL or PCL printout) with the rele vant printout in Chapter 10, Test Printout.

When the printout has the same format as shown in Chapter 9, the connection between the Xerox FS 3270 converter and the printer is working correctly.

Keep the settings printout together with this manual for future reference.

6.If the connection between the printer and the protocol con verter does not work properly, the reason is probably that the Y function 24 is not set to serial out or that the functions 15, 16, 17 and 18 do not match the values of the printer.

If the printout format does not match the test printout in Chapter 9, or if nothing was printed, this means that the printer setup does not match the protocol converter setup. Contact your systems support personnel or your i-datadealer.

- 14 -

Image 14
Contents EMC directive TrademarksSeptember PrefaceRelated Manuals Table of Contents Table of Contents Xerox FS 3270, Users Guide Introduction to Xerox FS Installation RequirementsPCL Driver Default Driver PCL or FSL output driverXerox FS 3270 Features Non-IPCXerox FS Supported Control UnitsItems Supplied Operating Environment Changing Paper Size Default US/EuropeIPC Upgrade Kit Xerox FS 3270 IPCInstallation Requirements Xerox FS 3270, Users Guide Installation and Connections of the Xerox FS Rear PanelChanging the Printer Driver Serial inputConnecting the Xerox FS 3270 to the Printer Upgrading to IPCConnecting via Centronics output Connecting via RS-232 outputConnecting to System Xerox FS 3270, Users Guide Connecting the Xerox FS 3270 to the System What if the CU Indicator fails to turn on?Testing PCL driverTimeout Settings Printout at Power-on PCL mode onlyCU Contact with Control Unit Indicators of the Xerox FSOperation of Xerox FS PAR Parallel inputSER Serial input Ready Printer ReadySpecifying Timeout ??character??%%Y100,30,1B,45%%X1 IdaSetup IPC Programming IRQ Handling PrinterPCL Driver Default Programming Xerox FS 3270 non-IPCSetup Functions Supported in PCL mode Where % is the defined ESC character Send Logo ESC FeaturesWhere % is the defined ESC character Engineering Functions User Settings Functions X-FunctionsTest functions T-Functions FunctionsSetup Functions Supported in FSL mode ESC Features User Settings Functions X-Functions ??%%Y100,10,’SHARESTRING’%%X1 FSL Setup via Xerox FS 3270 Serial or Parallel Port??%%Y249,PASSWORD%%Y100,10,’SHARESTRING’%%X1 Character conversionDeactivating the Y249 Engineering Function Limitations when Y249 is activeActivating the Y249 Engineering Function Updating Firmware Error Messages Recoverable ErrorsNot in engineering mode Non-Recoverable Hardware Errors PCL Test Printout Busy TimeoutTest Printouts Active Gfid = Gfid CPI=Proportionally Spaced = FSL Test Printout LPI Appendix a Quick Reference Guide to FSL FunctionsFSL N/S LPI FSL N/SEbcdic =PCL Y10=FSL Are wrapped Y12Y13 Y19 Y22FF after Y26,n1% = No FF Y35 Y41 EABY39 IRQ Y47Eeprom ESCEEPROM/RAM Y52Y55 Y53Y54 Y56HEX Y71Y74 Ascii HEX PCL modeFSL mode N2dataY79 APLName Syntax Parameters Deviations Y93 Y91Y92 Y94APO Y96Y98 Y112 Y110Y111 Y115 Y113Y114 Y118Re. T2 RAMData Example Cable connections to HP LaserJet Appendix B Using Serial OUTUse of Xerox FS 3270 serial port Appendix C Selected Xerox Products