Xerox Phaser 2135 manual Physical and Chemical Properties

Page 83

CEILING LIMIT: None established

XEROX EXPOSURE LIMIT (XEL): 2.5 mg/m3 (total dust); 0.4 mg/m3 (respirable dust)

SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES

APPEARANCE/ODOR: Black, blue, red, or yellow powders/faint odor

BOILING POINT: Not applicable

SOLUBILITY IN WATER: Insoluble

EVAPORATION RATE: Not applicable

VAPOR DENSITY (Air = 1): Not applicable

VOLATILE: Not applicable

SOFTENING RANGE: 110-140 degrees F (43-60 degrees C)

MELTING POINT: Not available

SPECIFIC GRAVITY (Water = 1): Approximately 1

VAPOR PRESSURE (mm Hg): Not applicable

pH: Not applicable

SECTION 10 - STABILITY AND REACTIVITY

STABILITY: Stable.

INCOMPATIBILITY WITH OTHER MATERIALS: Strong oxidizers

HAZARDOUS POLYMERIZATION: Will not occur

HAZARDOUS DECOMPOSITION PRODUCTS: During a fire, toxic gases may be generated by thermal decomposition or combustion.

SECTION 11 - TOXICOLOGICAL INFORMATION

This material has been evaluated by Xerox Corporation. The toxicity data noted below is based on test results of similar toners.

Oral LD50: > 5 g/kg (rats), practically non-toxic

Dermal LD50: > 5 g/kg (rabbits), practically non-toxic

Inhalation LC50: > 5 mg/l (rats; 4 hour exposure), practically non-toxic

Inhalation LD50: > 20 mg/l (rats; calculated for 1 hour exposure), non-toxic per

DOT

Eye Irritation: Non-irritating (rabbits)

Skin sensitization: Non-irritating (rabbits; human patch)

Human Patch: Non-irritating, non-sensitizing

Mutagenicity: No mutagenicity detected in Ames assay

Carcinogens: None present

Additional Information: The results obtained from a Xerox-sponsored Chronic Toner Inhalation Study demonstrated no lung changes in rats for the lowest (1 mg/m3) exposure level (i.e., the level most relevant to potential human exposure). A very slight degree of fibrosis was noted in 25 percent of the animals at the middle (4 mg/m3) exposure level, while a slight degree of fibrosis was noted in all the animals at the highest (16 mg/m3) exposure level.

Specifications

User Guide

67

Image 83

Contents L O R P R I N T E R Page Phaser 2135 Color Printer User Guide Page Page Printer Warranty WarrantyConsumables Warranty Page Electrical Safety User safety summaryMaintenance Safety 68 kg 149 lbs Do not switch off the printer power while printing Symbols as marked on product Page Contents Xiv Xerox Supplies and Accessories Part Number Customer-Replaceable Consumables CRCsHigh-Capacity Toner Cartridges Standard Toner CartridgesImaging Drum Rainbow Pack Imaging DrumsTransfer Belt 016-1927-00 FuserTransfer Belt Universal Tray Paper Cassette Only Xerox Phaser Professional Printing PaperCustomer Replaceable Units CRUs SuppliesXerox Phaser Color Laser Labels Xerox Phaser Professional Printing Paper contdXerox Phaser 35 Series Transparency Film Xerox Phaser Transparency Sleeves and PocketsCleaning Kit Xerox Phaser Premium Business CardsAutomatic Duplex Unit AccessoriesFeature Part Number Internal Hard DriveLower Tray Deck Lower Tray AssemblyAdditional Memory Front Panel Layout Front Panel UsageMenu Name Basic Menu NavigationPrinting the Menu Map Enhanced Print ModesStandard Color Modes Color ModeUnspecified RGB Phosphor settingsBlack Overprint Process GrayscalePaper Tips User Guide Supported page sizes and print area Supported page sizes and print areaSupported page sizes and print area cont’d Paper Specifics Universal TraySupported Media Capacity Supported MediaTransparency Specifics Universal Tray Loading Tray 1, 2, 3, 4, or 0748-25 Long-Edge Feed LEF Media Type Weight Media Specifics Multi-Sheet Bypass Feeder MBFSupported Media contd Loading the Multi-Sheet Bypass Feeder MBF Insert the media and adjust the guide for the media width Media Type Options Weight Xerox Phaser 35 Series Transparencies Guidelines for envelope printing Envelopes0748-33 0748-34 Automatic 2-Sided Printing From the Paper Tray Re-insert the Universal Tray Short-Edge binding or Flip on short edge Manual 2-Sided Printing Printing Side Top of the page should be toward the right of the tray From the MBF Multi-Sheet Bypass Feeder Media Type Options for Weight Sided Printing 0748-45 Top of the page should be toward the left of the tray Adjust the width and length guides to match the paper size Media Type Options for Weight Sided Printing Troubleshooting Print Quality Problems Only one color, an imaging drum may Print Quality Problem Common Causes Potential RemediesPrint Defects and Potential Remedies Only one color, an Print Defects and Potential Remedies contdBack-Side Contamination Color Misregistration What causes a media jam? Clearing Media JamsPreventing media jams Clearing Media Jams Open the top cover. Avoid touching or handling the LED bars Top Cover Jam0748-58 Remove the jammed media from the transfer belt area Replace the toner cartridges/imaging drum assemblies Duplex Unit Jam Right Door JamTray Misfeed Printer CD-ROM Getting HelpFront Panel Color Connection Xerox web siteInfoSMART Knowledge Base Canada Outside U.S. Other on-line servicesTo find a local reseller Asean Customer Support CenterIngredients percent by weight CAS number SpecificationsMaterial Safety Data Sheets Color Toner Cartridges Product Use Xerox Phaser 2135 Color PrintersChronic Effects None known Immediate EffectsPhysical and Chemical Properties Ecological Information Product Identification Material Safety Data Sheets CleanTex AlcopadEvaporation Rate Butyl ACETATE-1 Vapor Density AIR = 1 Sara Title III Reporting Other Information Chronic Effects Material Safety Data Sheets LED Lens CleanerIngredients CAS number Ethyl alcohol 64-17-5 First AID Measures Not available Other Information Index Phaser 2135 Color Printer User Guide Phaser 2135 Color Printer Page Printed on recycled paper