Xerox 701P39116 manual IPX/SPX Page 8830/8825 printers only

Page 28

network, the Web PMT will be completely unusable. For the Synergix Print Systems 8825, 8830, 8850 and 510dp, you can use the Printer Control Panel to undo this setting. For the Synergix Print Systems 8855 and 721p, you will need to upload a recovery file to the Controller through the serial or parallel port.

3.Netmask - These fields contain the value that the printer will use for its IP sub-net mask. The format is the same as the Ethernet TCP/IP Address.

4.Ethernet TCP/IP Address - These four fields contain the IP address of the Network Interface Card on the printer’s controller. The address is of the form "w.x.y.z" where the range for w, x, and y is 0-255 and z is 0-254.

5.Ethernet TCP/IP Gateway - These fields contain the IP address of the device the printer will use as the gateway or router. The format is the same as the Ethernet TCP/IP Address.

6.For the Synergix Print Systems 8855, 721p, and Synergix Color Print System X2 TECH, BEFORE pressing the Update Printer button, click on the indicated hypertext link to save a TCP/IP Recovery file. If the Web PMT becomes unusable, you can send this recovery file to the Controller through the serial or parallel port. For the 8825/8830/8850/ 510dp Printers, you MUST make a written record of these settings BEFORE clicking the Update Printer button.

NOTE: After modifying the IP Address, Subnet Mask, or Gateway, you should reboot (power off, then power on) the Controller to use the new settings.

IPX/SPX Page (8830/8825 printers only)

Navigation: PRINTER DEFAULTS > NETWORK > IPX/SPX

If you entered the printer password in the Session Setup, you can change the Novell IPX/SPX parameters in the printer if you have the network interface card. These parameters are described below:

1.Enabled - Click on this check box to enable/disable IPX/NDS on the printer.

2.IPX Frame Type - Click on this list box to select the IPX frame (link level) protocol. The possible values are AUTO, 802.3, 802.2, SNAP and ETHERNET2.

3.IPX Queue Scan Rate - Enter the query interval in integer seconds (0- 255). This controls the frequency with which NetWare file servers are queried for print jobs.

4.Bindery Mode (Novell 3.XX) - Click on this radio button to enable the Bindery Mode; the NDS Mode will be disabled.

Page 28

Web Print Manager Tool User Guide

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Web Printer Manager Tool User Guide for firmware version 701P39116 JanuaryTrademark Acknowledgments Table of Contents TCP/IP Web Print Manager Tool User Guide Web Printer Manager Tool Requirements Security Web PMT OverviewMain Menu Side Menu AccountingPrinter Defaults Pages Group Subgroups if anyQuick Start Starting the Web PMTDeselecting a Proxy In Netscape Proxies dialog, select Direct connection to the InternetViewing the Printer Configuration and Printing a Test Print Job Queue and Media StatusSelect Back to Main Media statusInstall Help Files Entering the Printer PasswordPrinter Language Canceling a Print Job Click on Printer Defaults Utilities Upload FileSend a test print Printer Defaults Test Print Normal Test Uploading a FileSetting the Accounting Mode Set Display UnitsMedia Mismatch Mode Adding a LabelUploading a Stamp to the Printer Mismatch QueueSelecting Color Parameters MediaSelect Printer Defaults Printer Setup Fonts Printer Resident GL/2 FontsPaper and Roll Sizes Controller Supported File FormatsMain Page and Printer Job Queue Navigation Back to MainSelected Print Job Navigation Back to Main Active Job Name linkNavigation Printer Defaults Test Print Test PrintSession Setup Password Configuration Feature ConfigurationUtilities Menu Upload FileChange Password Reset Printer DefaultsReset Error Log Page X2 Printer only Ports Menu Serial PortEtherTalk Page 8830/8825 printers only Network MenuNetBEUI Page 8830/8825 printers only TCP/IP IPX/SPX Page 8830/8825 printers only Web Print Manager Tool User Guide Printer Setup Menus Navigation Printer Defaults Printer Setup MiscellaneousMiscellaneous Plot NestingPen Palettes Web Print Manager Tool User Guide Pen Patterns Plot Labels Fonts StampsDate/Time Power Saver Page 8855 only Emulations Menu HpglCalcomp 906/907 Versatec Raster Navigation Printer Defaults Emulations VDSVDS Navigation Printer Defaults Emulations CGM CGMVcgl Navigation Printer Defaults Emulations VcglTiff PostScript Processing Defaults Menus FinishingJustification Intelligent title blockMargins MediaMedia Mismatch Mode Media Color Settings only for color inkjet printers Transform Web Print Manager Tool User Guide Rendering Introduction AccountingNavigation Accounting Job Accounting Error Displays Web Print Manager Tool User Guide Index CGMEmulations EOM DhcpHpgl IPX/SPX ISOPrinter Setup No FoldProcessing Defaults RARP/BOOTSession Setup ScsiUtilities Vcgl VDS Test Print TiffVPI Page USA
Top Page Image Contents