Belkin P75170EI manual Reset Button, Resetting the Router, Ii. Restoring the Factory Defaults

Page 18

Knowing your Router

J.Reset Button

The “Reset” button is used in rare cases when the Router may function improperly. Resetting the Router will restore the Router’s normal operation while maintaining the programmed settings. You can also restore the factory default settings by using the “Reset” button. Use the restore option in instances where you may have forgotten your custom password.

i.Resetting the Router

Push and release the “Reset” button. The lights on the Router will momentarily flash. The “Power/Ready” light will begin to blink. When the “Power/Ready” light becomes solid again, the reset is complete.

ii.Restoring the Factory Defaults

Press and hold the “Reset” button for at least 10 seconds, then release it. The lights on the Router will momentarily flash. The “Power/Ready” light will begin to blink. When the “Power/Ready” light becomes solid again, the restore is complete.

K.Power Jack – Black

Connect the included 12V/1A DC power supply to this jack.

1

2

3

4

5

6

7

8

9

10

section

14

Image 18

Contents N1 Wireless Router F5D8231-4ei Page Table of Contents Advantages of a Wireless Network IntroductionRevolutionary N1 Wireless Technology with Mimo N1 Mimo Placement of your N1 Wireless Router Important Factors for Placement and SetupRouter Placement Choose the Quietest Channel for your Wireless Network Avoid Obstacles and InterferenceCordless Phones Secure Connections, VPNs, and AOL Country Number Product Overview Setup Assistant Integrated 10/100 4-Port SwitchBuilt-In Dynamic Host Configuration Protocol Dhcp Universal Plug and Play UPnPIntegrated N1 Wireless Access Point MAC Address FilteringKnowing your Router Package ContentsSetup Assistant Software System Requirements System RequirementsWireless Security Wireless-Computer StatusWired-Computer Status Modem Status Router/Power StatusWireless Status Internet StatusConnections to Wired Computers Gray Connection to Modem YellowIi. Restoring the Factory Defaults Reset ButtonResetting the Router Power Jack BlackConnecting and Configuring your Router Modem RequirementsUnplug your modem’s power Connecting and Configuring your Router Set Up the Router Run the Setup Assistant Soft- wareChecking Settings Confirmation ScreenProgress Screen Connecting and Configuring your Router Requesting Internet Account Info if needed Troubleshooting Connecting and Configuring your Router Alternate Setup Method Logging into the Router Logging out of the RouterUnderstanding the Web-Based Advanced User Interface Internet-Status Indicator Quick-Navigation LinksHome Button Features Login/Logout ButtonLAN Settings Internet SettingsAlternate Setup Method Setting your Connection Type Host Name Change WAN MAC AddressISP Gateway Address IP AddressSubnet Mask My ISP Provides More Than One Static IP AddressSetting your ISP Connection Type to PPPoE User Name PasswordService Name MTUPptp Account Pptp PasswordService IP Address My IP AddressMy Subnet Mask Connection ID optionalSelect your State User Decide Login Server Manually Setting Custom Domain Name Server DNS SettingsConfiguring your WAN Media Access Controller MAC Address Cloning your MAC AddressEntering a Specific MAC Address Using the Web-Based Advanced User Interface Viewing the LAN SettingsUsing the Web-Based Advanced User Interface Changing LAN SettingsLease Time Dhcp ServerIP Pool Local Domain NameConfiguring the Wireless Network Settings Viewing the Dhcp Client ListChanging the Wireless Network Name Ssid Changing the Wireless Channel Using the Wireless Mode Switch40MHz only Using the Bandwidth Switch20MHz only 20MHz/40MHz AutoUsing the Broadcast Ssid Feature Protected Mode Switch Changing the Wireless Security SettingsWPA2 Requirements Setting WPA/WPA2-Personal PSK Setting WPA Security Setting WPA-PSK Setting WEP Encryption Using a Hexadecimal Key Using the Access Point Mode Setting MAC Address Control Setting up an Allow Access List Setting up a Deny Access ListConfiguring the Firewall Configuring Internal Forwarding Settings Manually Entering Settings into the Virtual ServerChoosing an Application Setting Client IP Filters Enabling the Demilitarized Zone DMZ Using Dynamic DNS Setting up the Router’s Dynamic DNS Update ClientUtilities Blocking an Icmp PingRestarting the Router to Restore Normal Operation Restarting the RouterRestoring Factory Default Settings Saving a Current Configuration Restoring a Previous Configuration Using the Web-Based Advanced User Interface Updating the Firmware Checking for a New Version of FirmwareDownloading a New Version of Firmware Updating the Router’s Firmware Using the Web-Based Advanced User Interface Changing System Settings Setting or Changing the Administrator PasswordChanging the Login Time-Out Setting Setting the Time and Time Zone Enabling Remote ManagementEnabling/Disabling NAT Network Address Translation Enabling/Disabling Auto Firmware Update Enabling/Disabling UPnPManually Configuring Network Settings Manually Configuring Network Settings in Mac OS up toManually Configuring Network Settings Manually Configuring Network Adapters in Mac OSSection Manually Configuring Network Settings Manually Configuring Network Adapters in Windows 98SE or Me Recommended Web Browser Settings Microsoft Internet Explorer 4.0 or HigherNetscape Navigator 4.0 or Higher Troubleshooting Setup Assistant CD does not automatically startSetup Assistant cannot find my Router Setup Assistant cannot connect my Router to the Internet Troubleshooting Section Troubleshooting Can’t connect to the Internet wirelessly Troubleshooting Troubleshooting C3030FAF4BB2C3D44BC3D4E7E4 = 128-bit key Click OK, and then Apply to save the settings Do Belkin products support WPA? Troubleshooting XP WPA Troubleshooting Wireless Comparison Chart Technical Support Information Federal Communications Commission NoticeModifications Canada-Industry Canada ICHow to get service What will we do to correct problems?What is not covered by this warranty? What the period of coverage isHow state law relates to the warranty