Belkin P75170EI manual Setting MAC Address Control

Page 57

Using the Web-Based Advanced User Interface

Setting MAC Address Control

The MAC address filter is a powerful security feature that allows you

to specify which computers are allowed on the wireless network. Note: This list applies only to wireless computers. This list can be

configured so any computer attempting to access the wireless network that is not specified in the filter list will be denied access. When you enable this feature, you must enter the MAC address of each client (computer) to which you want to allow network access. The “Block” feature lets you turn on and off access to the network easily for any computer without having to add and remove the computer’s MAC address from the list.

53

Image 57

Contents N1 Wireless Router F5D8231-4ei Page Table of Contents Introduction Advantages of a Wireless NetworkRevolutionary N1 Wireless Technology with Mimo N1 Mimo Placement of your N1 Wireless Router Important Factors for Placement and SetupRouter Placement Choose the Quietest Channel for your Wireless Network Avoid Obstacles and InterferenceCordless Phones Secure Connections, VPNs, and AOL Country Number Product Overview Built-In Dynamic Host Configuration Protocol Dhcp Integrated 10/100 4-Port SwitchSetup Assistant Universal Plug and Play UPnPMAC Address Filtering Integrated N1 Wireless Access PointSetup Assistant Software System Requirements Package ContentsKnowing your Router System RequirementsWireless Security Wireless-Computer StatusWired-Computer Status Wireless Status Router/Power StatusModem Status Internet StatusConnection to Modem Yellow Connections to Wired Computers GrayResetting the Router Reset ButtonIi. Restoring the Factory Defaults Power Jack BlackModem Requirements Connecting and Configuring your RouterUnplug your modem’s power Set Up the Router Run the Setup Assistant Soft- ware Connecting and Configuring your RouterChecking Settings Confirmation ScreenProgress Screen Connecting and Configuring your Router Requesting Internet Account Info if needed Troubleshooting Connecting and Configuring your Router Alternate Setup Method Logging into the Router Logging out of the RouterUnderstanding the Web-Based Advanced User Interface Internet-Status Indicator Quick-Navigation LinksHome Button LAN Settings Login/Logout ButtonFeatures Internet SettingsAlternate Setup Method Setting your Connection Type Change WAN MAC Address Host NameSubnet Mask IP AddressISP Gateway Address My ISP Provides More Than One Static IP AddressSetting your ISP Connection Type to PPPoE Service Name PasswordUser Name MTUService IP Address Pptp PasswordPptp Account My IP AddressConnection ID optional My Subnet MaskSelect your State Setting Custom Domain Name Server DNS Settings User Decide Login Server ManuallyConfiguring your WAN Media Access Controller MAC Address Cloning your MAC AddressEntering a Specific MAC Address Viewing the LAN Settings Using the Web-Based Advanced User InterfaceChanging LAN Settings Using the Web-Based Advanced User InterfaceIP Pool Dhcp ServerLease Time Local Domain NameViewing the Dhcp Client List Configuring the Wireless Network SettingsChanging the Wireless Network Name Ssid Using the Wireless Mode Switch Changing the Wireless Channel20MHz only Using the Bandwidth Switch40MHz only 20MHz/40MHz AutoChanging the Wireless Security Settings Using the Broadcast Ssid Feature Protected Mode SwitchWPA2 Requirements Setting WPA/WPA2-Personal PSK Setting WPA Security Setting WPA-PSK Setting WEP Encryption Using a Hexadecimal Key Using the Access Point Mode Setting MAC Address Control Setting up a Deny Access List Setting up an Allow Access ListConfiguring the Firewall Configuring Internal Forwarding Settings Manually Entering Settings into the Virtual ServerChoosing an Application Setting Client IP Filters Enabling the Demilitarized Zone DMZ Setting up the Router’s Dynamic DNS Update Client Using Dynamic DNSBlocking an Icmp Ping UtilitiesRestarting the Router Restarting the Router to Restore Normal OperationRestoring Factory Default Settings Saving a Current Configuration Restoring a Previous Configuration Using the Web-Based Advanced User Interface Checking for a New Version of Firmware Updating the FirmwareDownloading a New Version of Firmware Updating the Router’s Firmware Using the Web-Based Advanced User Interface Changing System Settings Setting or Changing the Administrator PasswordChanging the Login Time-Out Setting Enabling Remote Management Setting the Time and Time ZoneEnabling/Disabling NAT Network Address Translation Enabling/Disabling UPnP Enabling/Disabling Auto Firmware UpdateManually Configuring Network Settings in Mac OS up to Manually Configuring Network SettingsManually Configuring Network Adapters in Mac OS Manually Configuring Network SettingsSection Manually Configuring Network Settings Manually Configuring Network Adapters in Windows 98SE or Me Microsoft Internet Explorer 4.0 or Higher Recommended Web Browser SettingsNetscape Navigator 4.0 or Higher Troubleshooting Setup Assistant CD does not automatically startSetup Assistant cannot find my Router Setup Assistant cannot connect my Router to the Internet Troubleshooting Section Troubleshooting Can’t connect to the Internet wirelessly Troubleshooting Troubleshooting C3030FAF4BB2C3D44BC3D4E7E4 = 128-bit key Click OK, and then Apply to save the settings Do Belkin products support WPA? Troubleshooting XP WPA Troubleshooting Wireless Comparison Chart Technical Support Federal Communications Commission Notice InformationCanada-Industry Canada IC ModificationsWhat is not covered by this warranty? What will we do to correct problems?How to get service What the period of coverage isHow state law relates to the warranty