3M manual Setting up Your M2256PW Multi-touch Display, System Requirements

Page 10

10	3M™ Multi-touch Display M2256PW User Guide

CHAPTER 2

Setting up Your M2256PW Multi-touch Display

This chapter describes how to set up your 3M Touch Systems M2256PW Multi-touch Display. You need to complete the following tasks:

•Unpack the components

•Connect the video, touch display cables, and power cables

•Power on the display and test your setup

•If you are not running Windows 7 (or Tablet PC), install MT7 software from the enclosed CD. Note that this will not make multitouch happen -- it is up to your application to enable multitouch.

System Requirements

The M2256PW Multi-touch Display requires a personal computer (PC). The requirements for your PC are as follows:

•Your PC must have an available USB or RS-232 serial communication (COM) port. You connect the touch sensor cable to this port.

•Your PC must have a video card and video driver already installed for the display. If you need to install a video card or a video driver, refer to your computer documentation for instructions.

When choosing your workspace, select a sturdy, level surface. Also, make sure you can easily access the back of the touch display and the computer. Easy access helps ensure a smooth setup of the touch display.

Note: Before setting up your M2256PW Multi-touch Display, refer to the “Important Safety Information” section at the beginning of this document.

3M Touch Systems, Inc. Proprietary Information – 37531 Rev D

Image 10

Contents 3M Touch Systems, Inc. Proprietary Information 37531 Rev D 3M Multi-touch Display M2256PW User Guide Contents Appendix B 3M PX Serial Controller Communications Appendix a 3M PX USB Controller CommunicationsAppendix C Regulatory Information Overview Important Safety InformationIntroduction Intended UseExplanation of Signal Word Consequences Important Notes Maintaining Your Touch DisplayTouch Sensor Care and Cleaning 3M Touch Systems Support ServicesContact 3M Touch Systems Setting up Your M2256PW Multi-touch Display System RequirementsUnpacking Your Touch Display Cables Included with Your M2256PW Multi-touch DisplayTesting the M2256PW Multi-touch Display Connecting the Touch DisplayArm Mounting Option Video Card Requirements Using the Standard Controls for the Video CardApplicable Display Mode and Refresh Rate Refresh Rate Hz Supported Video Display Modes and Refresh RatesAccess to the Video Controls Configuring the Display SettingsMultimedia Features Menu/Select Down Up Auto/Exit Power LEDAdjusting the M2256PW Video Display Choices DescriptionAudio Tools All Other Platforms Enabling Your M2256PW Multi-touch DisplayWindows 7 USB Compatibility Multitouch Application SupportInstalling 3M MicroTouch Software Video Alignment3M Multi-touch Display M2256PW User Guide Overview of USB Firmware Communications 3M PX USB Controller CommunicationsCommunication Basics Receiving Reports from the Controller Command SetSet Feature Calibration HID Class RequestsDetermining Target Areas Calibration Setup Stage Offset Field Size Value DescriptionCalibration Response Command Status Byte Description Data Stage Offset Field Size Value DescriptionGet Feature GetStatus Valid Command Status Field Entries Response Description Get Feature GetMaxCountPower On Check Bit Fields Bit Number Description Setup Stage Offset Field Size Value DescriptionReset Setup Stage Offset Field Size Value Description Set Feature ResetReset Data Stage Offset Field Size Value Description Asynchronous Reports Set Feature -Restore DefaultsCoordinate Data MultiTouch Digitizer mode Async Report Offset Field Size Value DescriptionTouch Report Structure Offset Field Value DescriptionOverview of Firmware Commands 3M PX Serial Controller CommunicationsCommunicating with the Controller Controller Default SettingsOperating Mode Communication ParametersSending Commands to the Controller Receiving Responses from the ControllerFirmware Commands Controller InitializationMDU Command Code DescriptionCalibrate SOH CxcrGuidelines for Calibrate Command Calibrate ProcedureMode Stream Mode Down UpMode Inactive Get CopyrightSoft Reset Name CommandNull Command Output IdentityUnit Type Restore DefaultsOperating Parameter Default SOH RdcrBit Description Touch Data FormatData Sequence Bits Data Sequence Bits Regulatory Agency Approvals Regulatory InformationFCC-B FCC Warning CE Conformity for Europe