3M M2256PW manual FCC Warning, CE Conformity for Europe

Page 41

3M™ Multi-touch Display M2256PW User Guide

41

CAUTION

You are cautioned that any change or modification to the equipment not expressly approved by the party responsible for compliance could void your authority to operate such equipment.

This Class B digital apparatus meets all requirements of the Canadian Interference- Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

This device complies with Part 15 of the FCC rules: Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Warning

To assure continued FCC compliance, the user must use grounded power supply cord and the provided shielded video interface cable with bonded ferrite cores. If a BNC cable is going to be used, use only a shielded BNC(5) cable. Also, any unauthorized changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device.

3M Touch Systems is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment.

CE Conformity for Europe

The device complies with the requirements of the ECC directive 2004/108/EC with regard to “Electromagnetic compatibility” and 2006/95/EC with regard to "Safety".

3M Touch Systems, Inc. Proprietary Information – 37531 Rev D

Image 41

Contents 3M Touch Systems, Inc. Proprietary Information 37531 Rev D 3M Multi-touch Display M2256PW User Guide Contents Appendix C Regulatory Information Appendix a 3M PX USB Controller CommunicationsAppendix B 3M PX Serial Controller Communications Introduction Important Safety InformationOverview Intended UseExplanation of Signal Word Consequences Maintaining Your Touch Display Important Notes3M Touch Systems Support Services Touch Sensor Care and CleaningContact 3M Touch Systems System Requirements Setting up Your M2256PW Multi-touch DisplayCables Included with Your M2256PW Multi-touch Display Unpacking Your Touch DisplayArm Mounting Option Connecting the Touch DisplayTesting the M2256PW Multi-touch Display Applicable Display Mode and Refresh Rate Refresh Rate Hz Using the Standard Controls for the Video CardVideo Card Requirements Supported Video Display Modes and Refresh RatesMultimedia Features Configuring the Display SettingsAccess to the Video Controls Menu/Select Down Up Auto/Exit Power LEDChoices Description Adjusting the M2256PW Video DisplayAudio Tools Windows 7 USB Compatibility Enabling Your M2256PW Multi-touch DisplayAll Other Platforms Multitouch Application SupportVideo Alignment Installing 3M MicroTouch Software3M Multi-touch Display M2256PW User Guide Communication Basics 3M PX USB Controller CommunicationsOverview of USB Firmware Communications Set Feature Calibration Command SetReceiving Reports from the Controller HID Class RequestsCalibration Response Command Status Byte Description Calibration Setup Stage Offset Field Size Value DescriptionDetermining Target Areas Data Stage Offset Field Size Value DescriptionGet Feature GetStatus Power On Check Bit Fields Bit Number Description Get Feature GetMaxCountValid Command Status Field Entries Response Description Setup Stage Offset Field Size Value DescriptionReset Data Stage Offset Field Size Value Description Set Feature ResetReset Setup Stage Offset Field Size Value Description Coordinate Data MultiTouch Digitizer mode Async Report Set Feature -Restore DefaultsAsynchronous Reports Offset Field Size Value DescriptionValue Description Touch Report Structure Offset Field3M PX Serial Controller Communications Overview of Firmware CommandsOperating Mode Controller Default SettingsCommunicating with the Controller Communication ParametersReceiving Responses from the Controller Sending Commands to the ControllerController Initialization Firmware CommandsCalibrate Command Code DescriptionMDU SOH CxcrCalibrate Procedure Guidelines for Calibrate CommandMode Inactive Mode Down UpMode Stream Get CopyrightNull Command Name CommandSoft Reset Output IdentityOperating Parameter Default Restore DefaultsUnit Type SOH RdcrData Sequence Bits Touch Data FormatBit Description Data Sequence Bits FCC-B Regulatory InformationRegulatory Agency Approvals CE Conformity for Europe FCC Warning