Star Micronics LC-100+, LC-1011C user manual Loading fanfold paper

Page 19

Loading fanfold paper 11

far apart). After making these adjustments, be sure that you re-lock the tractors by pulling the gray levers into the locked position.

❏Close the rear cover and press down gently on it until it locks into place with a click.

Note:

If you removed the rear cover, ﬁrst insert its two tabs into the holes provided in the back of the printer and then swing it closed.

❏Install the paper guide so that it lays down ﬂat as shown below. In this position, the paper guide keeps the printed paper separate from the unprinted paper.

❏Turn on the printer.

The printer will beep a number of times to indicate that paper is not loaded properly. Also, the control panel’s POWER indicator flashes whenever paper is not loaded.

Image 19

Contents LC-1011C LC-100 + Colour EC Council Directive 73/23/EEC and 93/68/EEC of 22 July Trademark acknowledgments Chapter About this manualContents Using the Printer with MS-DOS Using the EDS ModePaper Handling Page Page Choosing a place for the printer Printer SetupUnpacking the printer General guide Opening the front cover Installing the platen knobInstalling the ribbon cassette Installing the ribbon cassettePrint head shield Ribbon cassette Removing the ribbon cassette Removing the ribbon cassette Connecting to a power outlet and turning power on and off Installing the paper guideLoading fanfold paper Loading fanfold paperSwing the rear cover back and down until it stops Loading fanfold paper Printing on fanfold paper Unparking fanfold paper Parking fanfold paperConnecting to your computer Using the tear-off functionConnecting to your computer Control Panel Operations Switching between on-line and off-lineLit Indicator Font Name Entering the Font Lock ModeSelecting a font Entering the Pitch Lock Mode Setting the character pitchLit Indicators Meaning Paper eject cut-sheet paper Line feedForm feed fanfold paper Micro feed Setting the top of form positionTear-off function fanfold paper Changing the auto load position Selecting the Quiet Print ModeSaving a macro Initializing the printer Clearing the printer’s bufferAbout EDS Mode settings Using the EDS ModeEntering the EDS Mode Lit Indicator Selected Switch Selecting a switchChanging a switch setting Lit Indicator Selected BankSwitch 1 Emulation Printing the current switch settingsExiting the EDS Mode EDS Mode SettingsSwitch 6 CR Centering Switch 3 RAM UsageSwitch 4 Automatic Sheet Feeder Switch 5 Paper Out DetectorSwitch 4 Auto LF with CR Switch 1 NLQ DirectionSwitch 2 Auto Tear-off Long Switch 3 Line SpacingSwitch 6 Quiet Switch 1 Print ModeSwitch 2 Printable Area Switches 3, 4, 5 Print PitchRibbon Type Switches 1, 2, 3, 4 Page LengthSwitches 5, 6 Ribbon Select LengthCode Switches 1, 2, 3, 4, 5 Code Page/International Character SetInternational Switch 1 NLQ Font SelectionCharacter Set Setting up for printing with MS-DOS Using the Printer with MS-DOSUsing the Printer with MS-DOS Cut-Sheet Paper with Optional Automatic Sheet Feeder Paper HandlingSelecting paper types Cut-Sheet Paper Manual FeedPaper Type Adjusting for paper thicknessThickness Manual sheet feeding Automatic fanfold feedingClearing paper jams Automatic Sheet Feeder SF-10DT Optional AccessoriesInstalling the Automatic Sheet Feeder Automatic Sheet Feeder SF-10DT Loading Paper Automatic Sheet Feeder SF-10DT Serial-to-Parallel Interface Converter Connecting the Interface ConverterFunction Setting the converter’s DIP switchesProtocol Data Length SwitchDOS/Windows Setting ParityTesting the printer Appendix a TroubleshootingShort test Long test Hexadecimal dumpAdjusting the dot alignment Problem Possible Cause Troubleshooting guideTroubleshooting guide Printed on Printer case is hot Printer’s air vents are Left margin moves to Paper is not loaded Enter the EDS Mode To check the application printer selection Checking system software settings in WindowsTo check the default printer selection To check the driver SetupTo check the port Checking system software settings in MS-DOSAppendix B Speciﬁcations Fanfold with push tractor feeder Dimensions and WeightPower Supply Power ConsumptionPin Name Function Appendix C Interface Pin OutsParallel Interface Optional Serial InterfaceStandard Italic Character Set #2 International Character Set Appendix D Character SetsCode Page #852 Latin-2 Code Page #863 Canadian French Code Page #860 Code Page #861 Portuguese IcelandicCode Page #865 Nordic Code Page #3843 Polish Code Page #866 RussianCode Page #3841 Gost-Russian Code Page #3840 IBM-RussianCode Page #3847 Brazil-ABNT Code Page #3844Code Page #3845 Hungarian Code Page #3846 TurkishIBM Special Character Set Code Page #3848 Brazil-ABICOMPCharacter Set #1 Description Mode Ascii Code Font and Character Set Control CommandsAppendix E Printer Control Codes Top/Bottom Margin and Vertical Tab Commands Print Pitch Control CommandsBit Image Graphic Commands Special Print Mode CommandsForm Feed and Related Commands Download Character Commands Line Spacing CommandsHorizontal Print Position Control Commands ESC U1 Other CommandsAppendix F Glossary Sanserif Font Prop Pitch Paper Feed Quiet Cond On Line Appendix G Control Panel Operation GuideAUTOEXEC.BAT 45 MS-DOS Page Page Page Page Worldwide Headquarters