Star Micronics LC-100+, LC-1011C user manual Adjusting the dot alignment

Page 57
Repeat the above steps for each printing mode, if necessary.
Press PAPER FEED to change to another printing mode.
❏
❏
❏ After making changes to adjustments in all the printing modes you want, press ON LINE to exit the Dot Adjustment Mode and register your adjustments.
The above step performs alignment for the Draft 10/12 cpi printing mode only. You must make separate adjustments for the Draft 17/20 cpi, NLQ 10/ 12 cpi, NLQ 17/20 cpi, and Emphasize printing modes as well.

Adjusting the dot alignment 49

Adjusting the dot alignment

You may never have to use the procedure described in this section, but after you have been using your printer for some time you may find that the dots of some graphics do not align correctly. For example, what should look like:

may come out looking like one of the following:

or like this:

This is caused when mechanical parts of the printer get out of alignment. This happens only rarely and you may never experience it at all throughout the life of the printer. If you do have problems, use the following procedure to correct it.

❏Make sure that paper is loaded in the printer.

❏Turn off the printer.

❏While holding down the control panel’s PITCH and ON LINE buttons, turn the printer back on to enter the Dot Adjustment Mode.

The printer will print something like the following.

Draft-10/12 cpi CURRENT + 4

Note that the printer will feed the paper forward and back each time during this operation so you can view the printout.

❏If the three lines do not align properly, use FONT to move the middle line to the left or PITCH to move it to the right.

Page 56 Page 58
Image 57
Page 56 Page 58
Contents LC-1011C LC-100 + Colour EC Council Directive 73/23/EEC and 93/68/EEC of 22 July Trademark acknowledgments Chapter About this manualContents Using the EDS Mode Using the Printer with MS-DOSPaper Handling Page Page Choosing a place for the printer Printer SetupUnpacking the printer General guide Opening the front cover Installing the platen knobInstalling the ribbon cassette Installing the ribbon cassettePrint head shield Ribbon cassette Removing the ribbon cassette Removing the ribbon cassetteConnecting to a power outlet and turning power on and off Installing the paper guideLoading fanfold paper Loading fanfold paperSwing the rear cover back and down until it stops Loading fanfold paper Printing on fanfold paper Unparking fanfold paper Parking fanfold paperConnecting to your computer Using the tear-off functionConnecting to your computer Control Panel Operations Switching between on-line and off-lineEntering the Font Lock Mode Lit Indicator Font NameSelecting a font Setting the character pitch Entering the Pitch Lock ModeLit Indicators Meaning Line feed Paper eject cut-sheet paperForm feed fanfold paper Setting the top of form position Micro feedTear-off function fanfold paper Changing the auto load position Selecting the Quiet Print ModeSaving a macro Initializing the printer Clearing the printer’s bufferUsing the EDS Mode About EDS Mode settingsEntering the EDS Mode Changing a switch setting Selecting a switchLit Indicator Selected Bank Lit Indicator Selected SwitchExiting the EDS Mode Printing the current switch settingsEDS Mode Settings Switch 1 EmulationSwitch 4 Automatic Sheet Feeder Switch 3 RAM UsageSwitch 5 Paper Out Detector Switch 6 CR CenteringSwitch 2 Auto Tear-off Long Switch 1 NLQ DirectionSwitch 3 Line Spacing Switch 4 Auto LF with CRSwitch 2 Printable Area Switch 1 Print ModeSwitches 3, 4, 5 Print Pitch Switch 6 QuietSwitches 5, 6 Ribbon Select Switches 1, 2, 3, 4 Page LengthLength Ribbon TypeCode Switches 1, 2, 3, 4, 5 Code Page/International Character SetSwitch 1 NLQ Font Selection InternationalCharacter Set Setting up for printing with MS-DOS Using the Printer with MS-DOSUsing the Printer with MS-DOS Selecting paper types Paper HandlingCut-Sheet Paper Manual Feed Cut-Sheet Paper with Optional Automatic Sheet FeederAdjusting for paper thickness Paper TypeThickness Manual sheet feeding Automatic fanfold feedingClearing paper jams Automatic Sheet Feeder SF-10DT Optional AccessoriesInstalling the Automatic Sheet Feeder Automatic Sheet Feeder SF-10DT Loading Paper Automatic Sheet Feeder SF-10DT Serial-to-Parallel Interface Converter Connecting the Interface ConverterFunction Setting the converter’s DIP switchesDOS/Windows Setting Data Length SwitchParity ProtocolAppendix a Troubleshooting Testing the printerShort test Long test Hexadecimal dumpAdjusting the dot alignment Problem Possible Cause Troubleshooting guideTroubleshooting guide Printed on Printer case is hot Printer’s air vents are Left margin moves to Paper is not loaded Enter the EDS Mode To check the default printer selection Checking system software settings in WindowsTo check the driver Setup To check the application printer selectionTo check the port Checking system software settings in MS-DOSAppendix B Specifications Power Supply Dimensions and WeightPower Consumption Fanfold with push tractor feederParallel Interface Appendix C Interface Pin OutsOptional Serial Interface Pin Name FunctionStandard Italic Character Set #2 International Character Set Appendix D Character SetsCode Page #852 Latin-2 Code Page #860 Code Page #861 Portuguese Icelandic Code Page #863 Canadian FrenchCode Page #865 Nordic Code Page #3841 Gost-Russian Code Page #866 RussianCode Page #3840 IBM-Russian Code Page #3843 PolishCode Page #3845 Hungarian Code Page #3844Code Page #3846 Turkish Code Page #3847 Brazil-ABNTCode Page #3848 Brazil-ABICOMP IBM Special Character SetCharacter Set #1 Font and Character Set Control Commands Description Mode Ascii CodeAppendix E Printer Control Codes Top/Bottom Margin and Vertical Tab Commands Print Pitch Control CommandsSpecial Print Mode Commands Bit Image Graphic CommandsForm Feed and Related Commands Line Spacing Commands Download Character CommandsHorizontal Print Position Control Commands ESC U1 Other CommandsAppendix F Glossary Sanserif Font Prop Pitch Paper Feed Quiet Cond On Line Appendix G Control Panel Operation GuideAUTOEXEC.BAT 45 MS-DOS Page Page Page Page Worldwide Headquarters

LC-100+, LC-1011C specifications

Star Micronics has long been a trusted name in the world of printing technology, renowned for its innovative solutions that cater to various business needs. Among their popular offerings are the LC-1011C and LC-100+ models, which are designed to provide reliable and efficient printing, particularly in the retail, hospitality, and gaming industries.

One of the standout features of the LC-1011C is its compact design, which allows it to fit seamlessly into any workspace. Despite its small footprint, this model is packed with advanced capabilities that make it a powerful tool for businesses. Its high-speed printing technology ensures that receipts, tickets, and labels are produced rapidly without compromising quality, helping to enhance overall productivity.

The LC-1011C is equipped with advanced thermal print technology, which not only reduces energy consumption but also provides smudge-proof, water-resistant prints. This is particularly beneficial in environments where durability is a concern. Additionally, the printer boasts a user-friendly interface and easy-to-load paper design, making it suitable for operators of all experience levels.

In comparison, the LC-100+ model enhances the features of its predecessor with additional capabilities designed for modern businesses. It supports a wider range of media types, including multi-layer receipts and custom-sized tickets. This flexibility allows businesses to tailor their printing needs based on specific operational requirements.

Both models utilize Star Micronics’ versatile communication interfaces, including USB, Bluetooth, and Ethernet options, ensuring compatibility with various devices and systems. This connectivity enables easy integration into existing point-of-sale systems and enhances workflow efficiency.

Another key characteristic of the LC-1011C and LC-100+ is their robust build quality. Constructed to withstand the rigors of everyday use, these printers are designed for longevity, reducing the need for frequent replacements and thus lowering total cost of ownership.

In conclusion, the Star Micronics LC-1011C and LC-100+ printers stand out in the market due to their combination of compact design, advanced printing technology, versatile media support, and robust connectivity options. These features make them ideal choices for businesses seeking reliable, efficient, and user-friendly printing solutions. Whether in a bustling retail environment or a busy kitchen, these printers deliver exceptional performance that can keep pace with the demands of modern operations.
Top Page Image Contents