Star Micronics LC-1011C Switch 1 NLQ Direction, Switch 2 Auto Tear-off Long, Switch 5 Zero Style

Page 36

28Using the EDS Mode

BANK B

Switch 1: NLQ Direction

Selects uni-directional (ON) or bi-directional (OFF) printing for NLQ (Near Letter Quality) printing. Bi-directional printing (OFF) is faster, while uni- directional (ON) printing generally provides better print quality.

Switch 2: Auto Tear-off (Long)

Specifies whether the printer’s auto tear-off (long) feature (page 20) is enabled (OFF) or disabled (ON). Note that this setting controls the application software’s tear-off function only. It does not affect the manual tear-off function that is performed using the control panel buttons as described on page 14. The manual tear-off function is always enabled.

Switch 3: Line Spacing

Selects 1/6-inch (ON) or 1/8-inch (OFF) spacing between lines.

Switch 4: Auto LF with CR

Specifies whether auto LF with CR is enabled (OFF) or disabled (ON). When auto LF with CR is enabled (OFF), the printer automatically performs a line feed whenever it receives a carriage return from the computer. When it is disabled (ON), the computer must send both a line feed code and a carriage return code at the end of each line. Most applications do this automatically. Note the following checkpoints when trying to figure out which setting to use here:

✓If you find that your output is double-spaced when it should not be, turn this switch ON (Disabled).

✓If you find that lines are printing over each other, turn this switch OFF (Enabled).

Switch 5: Zero Style

Specifies whether a normal zero (ON) or a slashed zero (OFF) will be used. Selecting Normal (ON) prints zeros without lines running through them, while Slashed (OFF) prints zeros with a diagonal slash running through them.

Switch 6: Reserved

Page 35 Page 37
Image 36
Page 35 Page 37
Contents LC-1011C LC-100 + Colour EC Council Directive 73/23/EEC and 93/68/EEC of 22 July Trademark acknowledgments About this manual ChapterContents Using the EDS Mode Using the Printer with MS-DOSPaper Handling Page Page Printer Setup Choosing a place for the printerUnpacking the printer General guide Installing the platen knob Opening the front coverInstalling the ribbon cassette Installing the ribbon cassettePrint head shield Ribbon cassette Removing the ribbon cassette Removing the ribbon cassetteInstalling the paper guide Connecting to a power outlet and turning power on and offLoading fanfold paper Loading fanfold paperSwing the rear cover back and down until it stops Loading fanfold paper Printing on fanfold paper Parking fanfold paper Unparking fanfold paperUsing the tear-off function Connecting to your computerConnecting to your computer Switching between on-line and off-line Control Panel OperationsEntering the Font Lock Mode Lit Indicator Font NameSelecting a font Setting the character pitch Entering the Pitch Lock ModeLit Indicators Meaning Line feed Paper eject cut-sheet paperForm feed fanfold paper Setting the top of form position Micro feedTear-off function fanfold paper Selecting the Quiet Print Mode Changing the auto load positionSaving a macro Clearing the printer’s buffer Initializing the printerUsing the EDS Mode About EDS Mode settingsEntering the EDS Mode Selecting a switch Changing a switch settingLit Indicator Selected Bank Lit Indicator Selected SwitchPrinting the current switch settings Exiting the EDS ModeEDS Mode Settings Switch 1 EmulationSwitch 3 RAM Usage Switch 4 Automatic Sheet FeederSwitch 5 Paper Out Detector Switch 6 CR CenteringSwitch 1 NLQ Direction Switch 2 Auto Tear-off LongSwitch 3 Line Spacing Switch 4 Auto LF with CRSwitch 1 Print Mode Switch 2 Printable AreaSwitches 3, 4, 5 Print Pitch Switch 6 QuietSwitches 1, 2, 3, 4 Page Length Switches 5, 6 Ribbon SelectLength Ribbon TypeSwitches 1, 2, 3, 4, 5 Code Page/International Character Set CodeSwitch 1 NLQ Font Selection InternationalCharacter Set Using the Printer with MS-DOS Setting up for printing with MS-DOSUsing the Printer with MS-DOS Paper Handling Selecting paper typesCut-Sheet Paper Manual Feed Cut-Sheet Paper with Optional Automatic Sheet FeederAdjusting for paper thickness Paper TypeThickness Automatic fanfold feeding Manual sheet feedingClearing paper jams Optional Accessories Automatic Sheet Feeder SF-10DTInstalling the Automatic Sheet Feeder Automatic Sheet Feeder SF-10DT Loading Paper Automatic Sheet Feeder SF-10DT Connecting the Interface Converter Serial-to-Parallel Interface ConverterSetting the converter’s DIP switches FunctionData Length Switch DOS/Windows SettingParity ProtocolAppendix a Troubleshooting Testing the printerShort test Hexadecimal dump Long testAdjusting the dot alignment Troubleshooting guide Problem Possible CauseTroubleshooting guide Printed on Printer case is hot Printer’s air vents are Left margin moves to Paper is not loaded Enter the EDS Mode Checking system software settings in Windows To check the default printer selectionTo check the driver Setup To check the application printer selectionChecking system software settings in MS-DOS To check the portAppendix B Specifications Dimensions and Weight Power SupplyPower Consumption Fanfold with push tractor feederAppendix C Interface Pin Outs Parallel InterfaceOptional Serial Interface Pin Name FunctionAppendix D Character Sets Standard Italic Character Set #2 International Character SetCode Page #852 Latin-2 Code Page #860 Code Page #861 Portuguese Icelandic Code Page #863 Canadian FrenchCode Page #865 Nordic Code Page #866 Russian Code Page #3841 Gost-RussianCode Page #3840 IBM-Russian Code Page #3843 PolishCode Page #3844 Code Page #3845 HungarianCode Page #3846 Turkish Code Page #3847 Brazil-ABNTCode Page #3848 Brazil-ABICOMP IBM Special Character SetCharacter Set #1 Font and Character Set Control Commands Description Mode Ascii CodeAppendix E Printer Control Codes Print Pitch Control Commands Top/Bottom Margin and Vertical Tab CommandsSpecial Print Mode Commands Bit Image Graphic CommandsForm Feed and Related Commands Line Spacing Commands Download Character CommandsHorizontal Print Position Control Commands Other Commands ESC U1Appendix F Glossary Appendix G Control Panel Operation Guide Sanserif Font Prop Pitch Paper Feed Quiet Cond On LineAUTOEXEC.BAT 45 MS-DOS Page Page Page Page Worldwide Headquarters

LC-100+, LC-1011C specifications

Star Micronics has long been a trusted name in the world of printing technology, renowned for its innovative solutions that cater to various business needs. Among their popular offerings are the LC-1011C and LC-100+ models, which are designed to provide reliable and efficient printing, particularly in the retail, hospitality, and gaming industries.

One of the standout features of the LC-1011C is its compact design, which allows it to fit seamlessly into any workspace. Despite its small footprint, this model is packed with advanced capabilities that make it a powerful tool for businesses. Its high-speed printing technology ensures that receipts, tickets, and labels are produced rapidly without compromising quality, helping to enhance overall productivity.

The LC-1011C is equipped with advanced thermal print technology, which not only reduces energy consumption but also provides smudge-proof, water-resistant prints. This is particularly beneficial in environments where durability is a concern. Additionally, the printer boasts a user-friendly interface and easy-to-load paper design, making it suitable for operators of all experience levels.

In comparison, the LC-100+ model enhances the features of its predecessor with additional capabilities designed for modern businesses. It supports a wider range of media types, including multi-layer receipts and custom-sized tickets. This flexibility allows businesses to tailor their printing needs based on specific operational requirements.

Both models utilize Star Micronics’ versatile communication interfaces, including USB, Bluetooth, and Ethernet options, ensuring compatibility with various devices and systems. This connectivity enables easy integration into existing point-of-sale systems and enhances workflow efficiency.

Another key characteristic of the LC-1011C and LC-100+ is their robust build quality. Constructed to withstand the rigors of everyday use, these printers are designed for longevity, reducing the need for frequent replacements and thus lowering total cost of ownership.

In conclusion, the Star Micronics LC-1011C and LC-100+ printers stand out in the market due to their combination of compact design, advanced printing technology, versatile media support, and robust connectivity options. These features make them ideal choices for businesses seeking reliable, efficient, and user-friendly printing solutions. Whether in a bustling retail environment or a busy kitchen, these printers deliver exceptional performance that can keep pace with the demands of modern operations.
Top Page Image Contents