TRENDnet TEW455APBO manual Network Utility

Page 50

User Manual

TEW-455APBO High Power Wireless Outdoor PoE Access Point

3.4.7 Network Utility

The administrator can diagnose network connectivity via the PING utility.

Please click on Utilities -> Network Utility and follow the below setting.

Ping : This utility will help ping other devices on the network to verify connectivity. Ping utility, using ICMP packets, detects connectivity and latency between two network nodes. As result of that, packet loss and latency time are available in the Result field while running the PING test.

Destination IP/Domain : Enter desired domain name, i.e. www.google.com, or IP address of the destination, and click ping button to proceed. The ping result will be shown in the Result field.

Count : By default, it’s 5 and the range is from 1 to 50. It indicates number of connectivity test.

If the device is unable to receive replies for IP addresses or domain names from the outside of the local network such as the Internet, please verify your network settings, like default Gateway and DNS settings under System > LAN.

47

Image 50

Contents Page Table of Contents Page System Overview Introduction of TEW-455APBOSystem Concept Applications in Wireless Network  Configuration in AP Mode including Access Point + WDS Configuration in WDS Mode Pure WDS TEW-455APBO High Power Wireless Outdoor PoE Access Point  Configuration in CPE Mode Product Benefit Specification  Wireless Feature  Authentication/ Encryption Wireless Security Quality of Service  System AdministrationWireless Performance Considerations Package Contents Basic InstallationHardware Installation Panel Function DescriptionsWeb Management Interface Instructions  System Login  Launch Web Browser Login Success External Network Connection AP Mode ConfigurationOption System Wireless Administrator Status Network RequirementConfigure LAN IP  802.1d Spanning Tree VAP Setting, Security Settings, and Access Control Settings Wireless LAN Network CreationWireless General Setup Output Power Chart FCC Domain Etsi Domain Level Wireless Advanced Setup RTS/CTS TEW-455APBO High Power Wireless Outdoor PoE Access Point TEW-455APBO High Power Wireless Outdoor PoE Access Point Create Virtual AP VAP Virtual AP OverviewTEW-455APBO High Power Wireless Outdoor PoE Access Point Virtual AP Setup TOS Key Length Hex Ascii WPA General Settings  Main and secondary Authentication Radius Server Settings  Main or Secondary Accounting Radius Server Settings Dynamic WEP Settings  Main and secondary Accounting Radius Server Settings  Only Deny List MAC MAC Filter Setup Only Allow List MAC Wireless Network Expansion 3shows Point to Multiple Points with different Vlan settingsTOS  WDS MAC List  System Information Configure ManagementSystem Management Privileges TEW-455APBO High Power Wireless Outdoor PoE Access Point Configure System Time Configure UPnP Configure Snmp Setup TEW-455APBO High Power Wireless Outdoor PoE Access Point Backup / Restore and Reset to Factory Firmware Upgrade UpgradeNetwork Utility Reboot System Status System OverviewTEW-455APBO High Power Wireless Outdoor PoE Access Point Associated Clients Status  Status On/OffWDS Link Status  Status On/OffExtra Information TEW-455APBO High Power Wireless Outdoor PoE Access Point Event Log WDS Mode Configuration 1Point to Point ConfigurationWDS Setup 2shows Point to Multiple Points with different Vlan settings WDS MAC List System Status TEW-455APBO High Power Wireless Outdoor PoE Access Point WDS Link Status CPE Mode Configuration System Wireless Advance Utilities StatusConfigure WAN Setup  Reconnect Mode DNS Configure Ddns Setup Site Survey Access Control List IP Filter SetupIP/Mask Port Rule Source DestinationSide Two ways to set the Access Control List Resource Sharing 1 DMZVirtual Server Port Forwarding TCP System Status TEW-455APBO High Power Wireless Outdoor PoE Access Point TEW-455APBO High Power Wireless Outdoor PoE Access Point TEW-455APBO High Power Wireless Outdoor PoE Access Point Dhcp Clients Command Line InterfaceCLI Accessing the CLI with TelnetAccessing the CLI with SSH Utility Using the CLI  Wireless Type W to open Choose Device window  Specify Packet Size Enter packet size  Using password command Change root password Appendix A. WEB GUI Valid Characters Table a WEB GUI Valid CharactersSnmp Block Field Valid Characters General Setup DMZ Main Menu Sub Menu Group Admin Privilege Appendix B. Network manager PrivilegesAppendix C. Enabling UPnP in Windows XP TEW-455APBO High Power Wireless Outdoor PoE Access Point Limited Warranty PWP05202009v2 TEW-455APBO High Power Wireless Outdoor PoE Access Point