Transition Networks SMHB-TR-16 manual Introduction, Connectors at Back

Page 9

1. INTRODUCTION

Connectors at Back

Cascade (Bus) Connectors

Cascade Connectors

A

SerialAUX

B

T R A N S I T I O N

n e t w o r k s

Mpls, MN 55344

Model#: SMHB-TR-16

Caution : For continued protection against risk of fire, replace only with same type and rating of fuse : 250V 2A.

Caution : Disconnect power before replacing fuse.

Achtung!: Zum anhaltenden Schutz vor Feurgefahr, Sicherung nur mit einer gleichnamiger Stromstarke und Spannung ersetzen: 250V, 2A

Achtung!: Stromleitung ausschalten bevor Sicherung ersetzen!

ATTENTION: Couper le courant avant de replacer le fusible.

Input Power: 100-240 V

 

50/60 Hz

2A, 250V

0.5 A

Serial

Power Connector

 

A serial port connector for SNMP management and maintenance, two (2) Cascade (bus) connectors, and a power connector are provided at the back of the StackMaster™TR 16-Port.

NOTE: The AUX connector is intended for future development.

USER’S GUIDE

1-3

Image 9
Contents StackMaster TR FCC Regulations Canadian Regulations Compliance InformationEuropean Regulations Copyright RestrictionsNetwork Parameters Data Sheets Table of Contents Preface IntroductionResetting StackMasterTR Stack Recovery ProceduresReplacement Procedures StackMasterTR Field UpgradesStackMasterTR Preface Page Introduction Connectors Ring In/Ring Out ConnectorLobe Connectors Introduction Connectors at BackIndicators Power LEDInsert/Normal LEDs Management Board LEDs Port Status LEDsActive/Passive Switches SwitchesZDL Switch Reset Switch4Mbps/16Mbps Switch Page Site Considerations Site PlanningTCP/IP Network Parameters Data Sheet Network Parameters Data SheetsSite Planning Snmp Network Parameters Data SheetSerial Port Parameters Data Sheet Unpacking StackMasterTR 16-Port Equipment InstallationStacking Units in Rack or on Table Standard 19-Inch Rack InstallationTable-Top Installation InstallationCascading StackMasterTR Units When adding passive hub to RO port Connecting StackMasterTR to Token Ring NetworkConnecting Units to Power Resetting StackMasterTR 16-Port Stack Managed StackUnmanaged Stack Connecting to Ascii Terminal Main Bringing up Configuration SoftwareNetwork Parameters Setting Network and Snmp ParametersMain snmp Snmp ParametersANY Menu restart ANY Menu quit Resetting the StackMasterTR 16-PortOperation Power On/Power OffPage Fault Isolation MaintenanceInsert RI LED Normal RO LEDLobe Port LED Maintenance Recovery Procedures Replacing StackMasterTR 16-Port Unit Fuses Replacement ProceduresInstalling Snmp Management Board StackMasterTR 16-Port Field UpgradesMaintenance Installing Snmp Management Board Software Upgrade at Attached Ascii Terminal Software UpgradesObtaining Updated StackMasterTR 16-Port Software Connecting to Ascii TerminalStackMasterTR Resetting the StackMasterTR 16-Port Transferring the FileQuit Page Interface Connector Appendix A. Technical SpecificationsDimensions Network StandardsPage Twisted Pair Cable Specifications Appendix B. Cable SpecificationsRJ-45 Pin Specifications Null Modem Cable SpecificationsPage Cable Distance Page Approval Organization Marking Blk Red Appendix D. Approved European Power Cord SetPage Warranty Statement Five Year Warranty If not, and the product is covered by warranty, then Return Procedure

SMHB-TR-16 specifications

Transition Networks SMHB-TR-16 is an advanced media converter designed for the effective management and conversion of data between different network media types. This device offers a robust solution for organizations looking to bridge the gap between fiber optic and copper Ethernet networks seamlessly.

One of the key features of the SMHB-TR-16 is its capability to support multiple data rates, including 10/100/1000 Mbps. This versatility ensures compatibility with a wide range of networking environments, allowing users to integrate legacy systems with modern high-speed networks. The device features auto-sensing capabilities that adapt to the speed of the network, simplifying installation and reducing configuration time.

The SMHB-TR-16 is designed with multiple ports, enabling simultaneous connections for varied network configurations. This multi-port design supports 16 individual Ethernet interfaces, allowing organizations to connect numerous devices without the need for additional hardware. Furthermore, the device is equipped with both SFP (Small Form-factor Pluggable) and RJ-45 ports, offering flexibility in selecting the appropriate connection type based on specific networking scenarios.

Another significant characteristic of the SMHB-TR-16 is its comprehensive support for various network protocols, ensuring compatibility and seamless data flow in diverse environments. The device can handle protocols such as Ethernet, Fast Ethernet, and Gigabit Ethernet, making it a versatile addition to any network infrastructure.

Reliability is a hallmark of Transition Networks' products, and the SMHB-TR-16 is no exception. It is built to withstand harsh environmental conditions, featuring a ruggedized design that aids in maintaining performance in extreme temperatures and electromagnetic interference.

In terms of management features, the device includes LED indicators for power, link status, and activity monitoring, allowing administrators to effectively manage and troubleshoot network issues. The simplicity of the design makes it easy to integrate into any existing network, ensuring minimal disruptions during deployment.

Overall, the Transition Networks SMHB-TR-16 is an essential networking solution that combines flexibility, reliability, and advanced technology. It is ideal for organizations seeking to enhance their network infrastructure while ensuring compatibility across different media types and speeds. With its rich feature set and robust construction, the SMHB-TR-16 stands out as a reliable choice for modern data communication needs.