Transition Networks E-TBT-HB-0804, 33022.B specifications Maintenance, Connectors and Indicators

Page 6

Connectors and Indicators

CONNECTORS

Straight-through RJ-45 Connectors

X

–

1

2

3

4

5

6

7

8

Crossover RJ-45 (X) Connector

Eight (8) straight-through RJ-45 connectors, labeled 1-8, and one (1) crossover RJ-45 connector, labeled X, are located on the front of the LANMaster T8.

Power Adapter Connector

LED Indicators

 

1

2

3

4

 

 

Act

5 6 7 8

AUI

BNC

 

Link Status

BNC Connector

AUI Connector

One (1) AUI connector, one (1) BNC connector, and one (1) AC power supply adapter connector are located on the back of the LANMaster T8.

LED INDICATORS

 

 

 

 

 

Steady green Act(ivity) LED

 

 

 

 

 

indicates connection of the

 

 

 

 

 

LANMaster T8 to external AC

Act

1

2

3

4

powerr. Blinking green

 

 

 

 

Act(ivity) LED indicate

 

 

 

 

 

network traffic.

 

5 6 7 8

Steady green Link Status

 

 

Link Status

LEDs indicate (for each port)

 

the integrity of the network link at the RJ-45 connector. Blinking green Link/Receive LEDs indicate (for each port) reception of valid data.

5. MAINTENANCE

WARNING: DO NOT, UNDER ANY CIRCUMSTANCES, open and attempt to repair the LANMaster T8. Failure to observe this warning could result in personal injury or death from electrical shock.

NOTE: Failure to observe the above warning will immediately void the warranty.

Fault Isolation

If two network devices fail to communicate through the LANMaster T8, consider the following:

•Are the LEDs described in the previous section functioning properly?

•Do network devices have Link Integrity enabled?

•Do network devices communicate when the LANMaster T8 is not installed between them?

•Is flat or “silver satin” wire used in site internal wiring?

•Are internal wiring patch cords, punch down blocks, and wall jacks properly pinned or configured?

•Is the thinnet cable unbroken and properly connected?

•Are network interface cards properly configured?

Technical Support Contact

For assistance in fault isolation and in maintaining the LANMaster T8, contact:

Technical Support

(800) 260-1312

or your local distributor.

3

LANMaster™ T8

8-Port Ethernet™ Repeater Hub

16

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Lanmaster T8 8-PORT HUB Specifications TBT-HB-080410BASE-2 Cable Specifications 10BASE-T Cable and Connector SpecificationsLANMaster T8 Port Ethernet Repeater Hub Ethernet Cable Specifications Table of ContentsFeatures IntroductionLANMaster T8 Warranty Statement Networking the LANMaster T8Connectors MaintenanceConnectors and Indicators Technical Support ContactOperation Site ConsiderationsMonitoring Status LEDs Unpacking the LANMaster T8 InstallationPowering the LANMaster T8 Part NumberConnecting to Network Using Transceiver Installing Thicknet 10BASE-5 CableConnecting to 10BASE-5 Using AUI Drop Cable To install the LANMaster T8 on table or other flat surfaceSTRAIGHT-THROUGH/CROSSOVER CABLE/CONNECTOR Installing Network CableInstalling Thinnet 10BASE-2 Cable 10BASE-T RequirementsInstalling Twisted-Pair 10BASE-T Cable 10BASE-2 Requirements10BASE-5 Requirements 10-Mb/s Baseband Network Configuration Guidelines

33022.B, E-TBT-HB-0804 specifications

Transition Networks E-TBT-HB-0804,33022.B is a highly specialized network device designed to support the demanding needs of enterprise-grade communications. This high-performance media converter offers a seamless transition between copper-based Ethernet networks and fiber optic networks, making it an ideal solution for businesses looking to enhance their network infrastructure.

One of the main features of the E-TBT-HB-0804,33022.B is its 10/100/1000 Mbps auto-sensing Ethernet ports, which enable users to connect various devices without worrying about compatibility issues. This flexibility ensures that both legacy and modern devices can be integrated into the network, providing a cost-effective solution for organizations seeking to upgrade their systems without a complete overhaul.

The device is built with robust technologies that ensure reliable performance. It supports full-duplex and half-duplex operation modes, allowing for efficient data transmission across the network. Additionally, the E-TBT-HB-0804,33022.B is equipped with advanced Auto-MDI/MDIX capabilities, which eliminate the need for crossover cables and further simplify connections, making setup quicker and more convenient for IT personnel.

In terms of characteristics, the E-TBT-HB-0804,33022.B boasts a compact design that fits easily into any network environment. Its durable construction ensures longevity, while the fanless design contributes to silent operation, making it suitable for noise-sensitive locations. Furthermore, it features LED indicators that provide real-time monitoring of network status and activity, allowing for quick troubleshooting and maintenance.

Another noteworthy aspect of this device is its compatibility with various types of fiber optic cables, including single-mode and multimode fibers. This versatility enables organizations to choose the best cabling solution to meet their specific distance and bandwidth requirements. The E-TBT-HB-0804,33022.B is also designed to support PoE (Power over Ethernet), allowing users to power network devices directly through the Ethernet cable, reducing the number of power adapters needed.

In conclusion, Transition Networks E-TBT-HB-0804,33022.B is an essential tool for businesses seeking to bridge the gap between copper and fiber networks. With its blend of advanced features, reliable technologies, and durable design, it provides a seamless networking experience that can adapt to evolving organizational needs. Whether upgrading an existing network or building a new one, the E-TBT-HB-0804,33022.B is an excellent choice for enhancing connectivity and performance.
Top Page Image Contents