Transition Networks E-TBT-HB-0804, 33022.B Installing Network Cable, 10BASE-T Requirements

Page 10

Installing Network Cable

10BASE-T Requirements

STRAIGHT-THROUGH/CROSSOVER CABLE/CONNECTOR

NOTE: The 10BASE-T cable and RJ-45 jacks for hub to terminal device connections must be configured as straight through. The 10BASE-T cable and RJ-45 jacks for hub to hub connections must be configured as crossover.

The “X” port provided on the LANMaster T8 changes a physical straight through cable configuration to a logical crossover cable configuration for hub to hub connections.

Therefore, ensure that all 10BASE-T cable to be installed is straight- through:

1 2 3 4 5 6 7 8

Installing Thinnet 10BASE-2 Cable

The LANMaster T8 has a female BNC MDI connector installed at the back for connection to 10BASE-2 cable and comes with a mating T- connector and a 50-ohm segment terminator for making the cable connection.

To connect to 10BASE-2 network cable:

1.Locate or build IEEE 802.3 compliant 10BASE-2 cable with male BNC connectors installed at both ends.

2.Install the mating T-connector to the female BNC connector on the LANMaster T8.

3.Install 10BASE-2 cable to one side of the T-connector.

4.Install 10BASE-2 cable to other side of the T-connector

OR, if the LANMaster T8 is the last network device in the daisy chain, install a 50-ohm terminator.

5.Verify that the 10BASE-2 segment coax cable segment is terminated properly at both ends.

RJ-45 JACK

Straight Through Cable

at RJ-45 Plug

8

RJ-45 PLUG

1

50 ohm terminator

earth ground

In a coax thinnet installation, the first and last device in the daisy- chain must be terminated with a 50 ohm terminator. Additionally, the 10BASE-2 segment must be grounded to “earth

Hub . . . . . . . . . . . . . . . .PC, transceiver, NIC, printer

ground” at one end.

RJ-45 Male . . . . . . . . . . . . . . .RJ-45 Male

1 . . . . . . . . . . . . . . . . . . .1 2 . . . . . . . . . . . . . . . . . .2 3 . . . . . . . . . . . . . . . . . .3 6 . . . . . . . . . . . . . . . . . . .6

The two active pairs in a 10BASE-T network are pins 1 & 2 and pins 3 & 6. Use only dedicated wire pairs (such as blue/white & white/blue, orange/white & white/orange) for the active pins.

50 ohm terminator

7

LANMaster™ T8

8-Port Ethernet™ Repeater Hub

12

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Lanmaster T8 8-PORT HUB Specifications TBT-HB-080410BASE-T Cable and Connector Specifications 10BASE-2 Cable SpecificationsLANMaster T8 Port Ethernet Repeater Hub Ethernet Cable Specifications Table of ContentsIntroduction FeaturesLANMaster T8 Warranty Statement Networking the LANMaster T8Connectors MaintenanceConnectors and Indicators Technical Support ContactSite Considerations OperationMonitoring Status LEDs Unpacking the LANMaster T8 InstallationPowering the LANMaster T8 Part NumberConnecting to Network Using Transceiver Installing Thicknet 10BASE-5 CableConnecting to 10BASE-5 Using AUI Drop Cable To install the LANMaster T8 on table or other flat surfaceSTRAIGHT-THROUGH/CROSSOVER CABLE/CONNECTOR Installing Network CableInstalling Thinnet 10BASE-2 Cable 10BASE-T Requirements10BASE-2 Requirements Installing Twisted-Pair 10BASE-T Cable10BASE-5 Requirements 10-Mb/s Baseband Network Configuration Guidelines

33022.B, E-TBT-HB-0804 specifications

Transition Networks E-TBT-HB-0804,33022.B is a highly specialized network device designed to support the demanding needs of enterprise-grade communications. This high-performance media converter offers a seamless transition between copper-based Ethernet networks and fiber optic networks, making it an ideal solution for businesses looking to enhance their network infrastructure.

One of the main features of the E-TBT-HB-0804,33022.B is its 10/100/1000 Mbps auto-sensing Ethernet ports, which enable users to connect various devices without worrying about compatibility issues. This flexibility ensures that both legacy and modern devices can be integrated into the network, providing a cost-effective solution for organizations seeking to upgrade their systems without a complete overhaul.

The device is built with robust technologies that ensure reliable performance. It supports full-duplex and half-duplex operation modes, allowing for efficient data transmission across the network. Additionally, the E-TBT-HB-0804,33022.B is equipped with advanced Auto-MDI/MDIX capabilities, which eliminate the need for crossover cables and further simplify connections, making setup quicker and more convenient for IT personnel.

In terms of characteristics, the E-TBT-HB-0804,33022.B boasts a compact design that fits easily into any network environment. Its durable construction ensures longevity, while the fanless design contributes to silent operation, making it suitable for noise-sensitive locations. Furthermore, it features LED indicators that provide real-time monitoring of network status and activity, allowing for quick troubleshooting and maintenance.

Another noteworthy aspect of this device is its compatibility with various types of fiber optic cables, including single-mode and multimode fibers. This versatility enables organizations to choose the best cabling solution to meet their specific distance and bandwidth requirements. The E-TBT-HB-0804,33022.B is also designed to support PoE (Power over Ethernet), allowing users to power network devices directly through the Ethernet cable, reducing the number of power adapters needed.

In conclusion, Transition Networks E-TBT-HB-0804,33022.B is an essential tool for businesses seeking to bridge the gap between copper and fiber networks. With its blend of advanced features, reliable technologies, and durable design, it provides a seamless networking experience that can adapt to evolving organizational needs. Whether upgrading an existing network or building a new one, the E-TBT-HB-0804,33022.B is an excellent choice for enhancing connectivity and performance.
Top Page Image Contents