Manuals / Panasonic / Computer Equipment / Network Card

Panasonic AW-PH360N manual $ Assembling the pan/tilt head, OAttaching the tilting arm

Models: AW-PH360N

1 52

Download 52 pages 54.4 Kb

Page 9

Image 9

Installation (The installation work must be performed by your dealer without fail.)

$ Assembling the pan/tilt head

Be absolutely sure to hold the pan/tilt head by the base when handling it.

OAttaching the tilting arm

Use the tilting arm fixing screws to attach the tilting arm. The way in which the arm is mounted differs depending on the direction in which it is installed. (See the figure below.)

Suspended installation

Stand-alone installation

Tilting Arm

<Note>

Tighten up the screws securely to ensure that they will not come loose during use.

- 9 -

Page 9

Image 9

Panasonic AW-PH360N manual $ Assembling the pan/tilt head, OAttaching the tilting arm, Suspended installation

Contents

AW-PH360N Before attempting to connect, operate or adjust this productIndoor Pan/Tilt Head Printed in JapanHAZARDOUS MOVING PARTS KEEP FINGERS AND OTHER BODY PARTS AWAY 1 indicates safety informationFCC Note 1 indicates safety informationAccessories ContentsIntroduction AccessoriesInstallation precautions Precautions for use Parts and their functions 1 Tilting arm Parts and their functionsSuspended installation $ Assembling the pan/tilt headStand-alone installation OAttaching the tilting armFor stand-alone installation For suspended installationFor AW-RP605A For a soft landingOAnalog/IEEE1394 card settings $ Transmission signal selection settingOWEB card settings OSDI settings$ Setting the cable compensation circuit of video signals 2 When using the AW-RP605A controller3 When using the AW-RP400 controller Safety wire $ Installing the pan/tilt head$ Mounting the camera Stand-alone installationSuspended installation Mounting example when the camera side is heavy Stand-alone installationMounting example when the lens side is heavy Recommended lensesOAttaching the chain With the AW-E350/AW-E650With the AW-E655/AW-E750/AW-E860 OMounting a camera OAdjusting slack in the chainWith the AW-E350/AW-E650 With the AW-E655/AW-E750/AW-E860 Camera guide pin Camera mounting Screw Camera mounting ScrewConnections $ Connecting the connector panel with the controller AW-RP501Connections $ Connecting the connector panel with the controller AW-RP505Connections $ Connecting the connector panel with the controller AW-RP605AConnections $ Connecting the connector panel with the controller AW-RP400The BNC connectors are not connected to the pan/tilt head $ Connecting the connector panel RS-232C controlConnections DC cable UL Type SPT-2 2!161ND/EXT connector $ Head connector panel4CAMERA I/F connector 2 LENS I/F connector6 CONTROL IN IP/RP connector 5 1394 connector7 Y OUT connector 8 Pr/SDI OUT connectorG/L IN connector 9 Pb OUT connectorVIDEO OUT connector CAMERA CONTROL IN connectorConnections $ Connecting the AC adapter for use with the pan/tilt headDC 12V IN terminal board ? LAMP CONTROL terminal boardConnections $ Connection examplesColor monitor DC cableCamera cable supplied Color monitor Coaxial cable Connectionsmax. 1640 ft. 500 m 10BASE-TConnections Connections Connections Connections Connections Coaxial cable Camera cable supplied ConnectionsCoaxial cable BELDEN 8281, max.Color monitor 666 ft. 200 m Coaxial cable BELDEN 8281, max. 3333 ft. 1000 mpanel is used to control the camera ConnectionsCable supplied with AW-CB400 DC cable UL Type SPT-2 2!16 AWG orConnections Connections Connections Camera cable supplied Color monitor Coaxial cable ConnectionsRS-232C cable AW-CA28T9 AC adapterConnections For further details, refer to the web card instructions ConnectionsFor further details, refer to the IEEE1394 card instructions ConnectionsLimiters To release the setting $ Setting/releasing the limitersTo release the setting To release the settingTo release the setting To release the settingTo release the setting To release the settingTo release the setting To release the settingTo release the setting To release the setting$ Replacing the battery Replacement of consumable parts$ Replacing the motor $ Replacing the gearPower supply SpecificationsPower consumption DC +12 Maximum load capacity 8.8 lb 4 kg Allowable operating temperatureSpecifications $ Functions/performanceWeight Allowable operating humidityPage